SEWOO TECH CO.,LTD. 374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea TEL : +82-31-459-8200 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-P12W USER’S MANUAL Rev.
Table of Contents RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION 1. Unpacking 2 2. Product overview 3 3. Installation & Usage 4 3-1. Display 4 3-2. Installing the Battery 5 3-3. Removing the Battery 6 3-4. Charging the Battery 7 3-5. Stock Installation 8 3-6. Peel Mode 9 3-7. Diagnostic Test 11 4. Peripherals Connection 13 4-1. Wifi(802.11b/g) Connection 13 4-2. Interface Cable Connection 14 5.
2. Product overview 1.
3. Setting Up the Product 3-2. Installing the Battery 3-1. Display Button Name function Paper Feed/ Down button Advances the supply. Clears error message. Moves down through menu options. Enter button Selects the highlighted menu option. Up button Moves up through menu options. Power button Turns the printer on and off. Press to turn power on. Press for three seconds to turn power off. Wakes the printer from sleep mode. Remove the battery door. Insert the battery as shown. 1 2 NOTE 1.
3-3. Removing the Battery 3-4. Charging the Battery ② LED ① Remove the battery door. Lift out the battery. 1. Turn off the printer. 2. Be sure that the AC plug is correct. If AC plug is wrong, change the plug to the correct one. 3. Open the DC jack by pulling on the rubber cover and insert DC jack into the printer. 4. Plug the AC plug into an electrical outlet. 5. The charge indicator LED (located on the AC charger as shown) shows red or green according to the status.
3-6. Peel Mode 3-5. Stock Installation Peel Mode Open the Paper cover by pressing the Open button and set the width of paper guide by turning the knob with finger. 1 2 3 4 Close the cover. 8 Put the stock in so it unrolls from the bottom. Remove the stock core when it is empty. Pull a short length of stock out of the printer. With a roll of stock installed, slide the peeler body towards the back of the printer. Non-Peel Mode Press the Feed Key once to arrange the paper.
While Peeler mode is “On”, perhaps engraved lines of the label paper are cut too deep, peeling error might occur. 3-7. Diagnostic Test Badness Paper Laper Paper Engraved Line Turn off the printer. Press and hold the feed button and power button. Normal paper 1 2 3 Laper Paper NOTE 1. For Hex Dump mode, do steps 1-2 then press the feed button. 2. After printing ASCII pattern, the diagnostic test is complete. 3.
4. Peripherals Connection The sample of self test printout This printeThis product can communicate with other devices via Wifi(802.11b/g) communication and cable. 4-1 Wifi(802.11b/g) Connection 1. The Printer can be connected to devices equipped with wifi(802.11b/g) communication capacity (PDAs, PCs, etc.) 2. Use the wifi(802.11b/g) connection function supported by the device to connect to the printer.
5. Printer cleaning If the interior of the printer is dusty, printing quality can be lowered. In this case, follow the instructions below to clean the printer. 4-2. Interface Cable Connection 5-1. PrintHead Cleaning 1. Use an applicator swab moistened with an isopropyl alcohol to clean the print head and remove any dust. 2. Once cleaning is complete, allow the printer to dry then install the stock and close the cover. USB Serial PrintHead 1.
6. Printer Specification 5-2. Platen Roller Cleaning 1.Clean the platen roller with a clean soft cloth moistened with isopropyl alcohol or a cleaning pen. 2. Turn the platen roller with your finger to clean the entire surface. 6-1.
7. CPCL Command Compatibility Battery Charger NOTE input AC100~240V, 50/6 Hz output 7.4V, 2200mAh Battery type Li-ion output 7.4V, 18.9wh Charging time 3.7 Hrs Charging WXDXH(mm) 104 X 85 X 158 Printer Commands WXDXH” 3.9 X 3.3 X 6.
Graphics Line Print Mode Compatibility ○ SETLP ○ LINE ○ SETLF ○ INVERSE-LINE ○ Moving With X and Y Coordinates ○ PATTERN ○ LMARGIN ○ GRAPHICS ○ SETBOLD ○ PCX ○ SETSP ○ Special ASCII Characters ○ Advanced Commands Compatibility CONTRAST ○ SETFF ○ TONE ○ SET-TOF ○ JUSTIFICATION ○ SETLP-TIMEOUT ○ PAGE-WIDTH ○ PACE ○ NO-PACE ○ WAIT ○ REWIND TENSION X X SPEED ○ SETSP ○ ON-OUT-OF-PAPER X ON-FEED ○ PREFEED ○ POSTFEED ○ PRESENT-AT X COUNTRY/CODE PAGE