INSTALLATION INSTRUCTIONS CALL HELPLINE IF ANY ASSISTANCE IS REQUIRED
INSTRUCTION MANUAL CONTENTS 1 BOXED PARTS A full list of all parts supplied. Check your parts against this list to verify you have all components required before commencing with the installation. 2 FIT SCREEN BRACKETS Ascertain parts required and assemble screen brackets to TV. There are two options available. Option one includes an extension bracket and is for use with screens with vertical fixing centres between 400mm and 475mm.
9 HANG SUPPORT ARM ASSEMBLY Attach the main body of the product to the wall brackets. Slot the support arm assembly into place and fix with four screws (one on the end of each arm). 10 FIT TV SUPPORT BRACKET Attach the TV support bracket to the main body. Centralise bracket and bolt into place. 11 FIT SHELF MODULE Attach the shelf module to the main body. Slide the shelf module into place and fit the support nut and safety pin.
1 BOXED PARTS GLASS SHELF R-CLIP M8 x 25 SCREW C x1 BOTTOM GLASS SHELF D x1 A x1 B x2 E x1 F x2 G x2 H x1 I x1 J x1 K x1 L x1 CABLE CLIP M x18 N1 x1 N2 x1 O x1 LOCK PIN P x1 Q x2 R x1 T1 x4 M8 FULL NUT S1 x1 M6 x 16 SCREW T2 x8 M8 NUT S2 x5 M6 NUT S3 x8 M6 x 12 SCREW T3 M6 x 25 SCREW T4 x4 x4 4
1 M8 x 12 SCREW T5 M8 SPRING WASHER U2 x4 10mm WALL PLUG 2mm ALLEN KEY TEMPLATE x4 W x10 Y3 x1 M8 x 25 SCREW T6 x4 M4 x 16 GRUB SCREW T7 M6 WASHER U3 x12 M8 WASHER U4 x8 SPACER Y1 x1 6mm ALLEN KEY No14 x 2½" SCREW X x10 5mm ALLEN KEY LEVEL Z x1 TEMPLATE x1 TP1 x1 LARGE WASHER TEMPLATE U1 x1 V x4 Y2 x1 TP2 x1 TP3 x1 5
2 FIT SCREEN BRACKETS N2 T3-6 S2 U3-4 U4 Q T3-6 (IF REQUIRED) V U3-4 N1 V (IF REQUIRED) VERTICAL FIXING CENTRES OPTION 1 UNDERSIDE OF TV USE THIS OPTION FOR SCREENS WITH VERTICAL FIXING CENTRES OF BETWEEN 400mm-475mm USE SPACERS (V) IF THE REAR OF THE TV IS NOT FLAT OR THE FIXING HOLES ARE RECESSED IN TO THE BACK OF THE TV T3-6 U3-4 (IF REQUIRED) V T3-6 U3-4 V (IF REQUIRED) VERTICAL FIXING CENTRES OPTION 2 UNDERSIDE OF TV USE THIS OPTION FOR SCREENS WITH VERTICAL FIXING CENTRES OF 400mm AND BEL
3 SET TV SUPPORT BRACKET LENGTH N2 N1 AFTER INSTALLING SCREEN ADAPTERS (N1) AND (N2) (SEE SECTION 2), PLACE SUPPORT BRACKET (E) IN PLACE AND ADJUST ITS LENGTH AS SHOWN BELOW.
4 ASSEMBLE SHELF MODULE i ii INSERT SCREW HERE iii Y3 I I T7 T7 J J NOTE:- ALIGN HOLE EDGE TO EDGE OF PART (I) TO AID ALIGNMENT AND INSERTION OF GRUB SCREW (T7) iv ASSEMBLY OF THE SHELF MODULE IS A TWO PERSON OPERATION. LAY COMPONENTS ON THE FLOOR. ONE PERSON SHOULD HOLD SHELVES VERTICALLY WHILE ANOTHER SLIDES ON THE ADDITIONAL COMPONENTS AND FITS NUT (S2).
5 CREATE TEMPLATE MODIFICATION OF THE TEMPLATE (TP3) TO SUIT YOUR TV IS REQUIRED. THIS WILL ENABLE YOU TO USE IT IN CONJUNCTION WITH TEMPLATES (TP1) AND (TP2) TO SIMULATE THE MOUNT AND YOUR TV IN POSITION. YOU WILL THEN (USING THE TEMPLATES) EASILY BE ABLE TO DETERMINE WHERE AND AT WHAT ANGLE YOUR TV WILL BE AFTER INSTALLATION.
6 DETERMINE MOUNT AND TV POSITION USING TEMPLATES (TP1), (TP2) & (TP3) TO SIMULATE THE MOUNT AND TV IN YOUR ROOM, YOU CAN EVALUATE THE POSSIBLE POSITIONS AND LAYOUT OF THE MOUNT AND TV TP1 PLACE TEMPLATES (TP1), (TP2) & (TP3) ON FLOOR IN THE CORNER OF THE ROOM AS SHOWN READ THE WHOLE OF THIS SECTI0N (SECTION 6) AND USE THE RULES AND GUIDELINES DESCRIBED TO AID IN YOUR POSITIONING OF THE TEMPLATES TP2 TP3 FIG 2 FIG 1 TP1 EDGE “A” TP2 SLOT “B” MAX OPEN MAX CLOSED TEMPLATES (TP1) & (TP2) ARE USED TO
6 FIG 3 SHELF OUTLINE CORNER “D” HOLE “C” USE TEMPLATE (TP3) TO SIMULATE THE SCREEN AND SUPPORT SHELF ORIENTATION CORNER “D” TP3 ENSURE HOLE MARKED “C” (SEE FIG 3) IS INSIDE SLOT MARKED “B” (SEE FIG 1) FIG 4 CAUTION CLASH WHEN DETERMINING THE SCREEN ORIENTATION ENSURE CORNERS “D” (SEE FIG 3) DO NOT CLASH WITH (TP1) OR (TP2) (SEE FIG 4) X° RELEVANT TO STUDDED WALLS ONLY Y° IN THE INSTANCE WHERE STUDDED WALLS EXIST, THE STUD POSITION WILL INFLUENCE THE BRACKET POSITION.
6 THIS AREA MUST BE IN CONTACT WITH THE WALLS LINES DENOTE MIN/MAX ANGLE RANGE “E” “E” THE EDGES “E” REPRESENT THE MAXIMUM AND MINIMUM ANGLE TO THE WALL THAT THE TEMPLATES CAN BE PLACED 60° MAX 90° ARMS BEHIND TV 30° MIN 90° ENSURE VIEWING ANGLE IS SUITABLE FOR ROOM.
7 DETERMINE WALL BRACKET POSITION MAKE ALLOWANCES FOR SKIRTING/BASE BOARD. ONCE YOU HAVE DECIDED ON THE POSITIONING OF THE UNIT, TAPE THE TEMPLATES (TP1), (TP2) & (TP3) TOGETHER AND LIFT THEM ABOVE SKIRTING/BASE BOARD WHILE MARKING THE WALL (ENSURE TEMPLATES REMAIN PARALLEL WITH FLOOR). THIS WILL REMOVE INACCURACIES IN POSITIONING THE WALL BRACKETS (F) DUE TO THE THICKNESS OF THE SKIRTING/BASE BOARD.
7 DIM “H” MIN 965mm (38") ii POINT “K” FIG 8 F Z POSITION THE WALL BRACKET (F) WITH THE TOP FIXING HOLE ON CENTRE WITH THE POINT “K” ALREADY MARKED USING A LEVEL TO ENSURE THE BRACKETS ARE VERTICAL MARK THE OTHER 4 FIXING POINTS (SEE FIG 8) FIG 9 REPEAT ALL OPERATIONS FOR 2nd BRACKET DIM “H” MIN 965 (38") iii IMPORTANT ! ENSURE BOTH WALL BRACKETS (F) ARE INSTALLED AT THE SAME HEIGHT.
10mm Ø 8 FIT WALL BRACKETS DRILL Ø10mm HOLE FOR PLUG (W) 65mm (2½") MASONRY W X F W WHEN FIXING TO BRICKWORK OR SOLID MASONRY, USE SUITABLE WALL PLUGS AND SCREWS (NOT SUPPLIED WITH ALL MODELS). DO NOT MOUNT ONTO SHEETROCK, PLASTERBOARD OR PANELLED WALLS UNLESS SCREWS ARE FIXED INTO A SUITABLE WOODEN BATTEN/STUD. IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE THE WALL STRUCTURE AND FIXINGS ARE CAPABLE OF SUPPORTING THE AV EQUIPMENT AND MOUNT IN A NORMAL WORKING ENVIRONMENT.
9 HANG SUPPORT ARM ASSEMBLY ENSURE TELESCOPIC ARMS ARE INSERTED THE CORRECT WAY AROUND TO SUIT YOUR INSTALLATION. REFER TO YOUR TEMPLATE LAYOUT (SEE SECTION 6). (TP1) REPRESENTS THE EXTERNAL MEMBER, (TP2) REPRESENTS THE INTERNAL MEMBER.
10 FIT TV SUPPORT BRACKET Y1 T2 E U3 S3 E ENSURE TV SUPPORT BRACKET IS CENTRALISED ON SUPPORT ARM ASSEMBLY 11 ROOM AND WALL BRACKETS NOT SHOWN FOR CLARITY FIT SHELF MODULE PUSH THREADED BAR THROUGH HOLE INSTALLATION OF THE SHELF MODULE IS A TWO PERSON OPERATION.
11 S1 U1 R IMPORTANT ! ENSURE SAFETY R-CLIP (R) IS INSTALLED 12 ADJUSTING SHELF LEVEL Y1 TOP ADJUSTING SCREW BOTTOM ADJUSTING SCREW CHECK SHELF LEVEL.
13 ADJUSTING SHELF HEIGHT S1 105mm (4 1/8") HEIGHT ADJUSTMENT USE NUT (S1) TO ADJUST SHELF HEIGHT 14 FITTING COVERS G K L 19
15 HANG TV i ENSURE BOTH LOCKING SCREWS (ONE ON EACH BRACKET) ARE IN THE RETRACTED POSITION SHOWN (NO THREAD PROTRUDING ABOVE SURFACE) ii iii SCREW LOCKING SCREW INTO THE FULLY ENGAGED POSITION AS SHOWN TO SECURE TV (BOTH BRACKETS) 20
16 LOCK TV (OPTIONAL) P USE A PAD LOCK (NOT SUPPLIED) THROUGH THIS HOLE TO PREVENT UNAUTHORISED REMOVAL OF THE TV 17 TILT / ROTATE / SLIDE OPTIONAL TILT LOCK: IF REQUIRED YOU CAN LOCK THE TILTING MECHANISM BY TIGHTENING THESE NUTS (4 PLACES) TILT 21
17 ROTATE PUSH HERE PUSH HERE SLIDE 22
CUSTOMER SERVICES HELPLINE AVF Group Ltd. Road 30, Hortonwood Industrial Estate, Telford, Shropshire, TF1 7YE, England. +44 (0) 1952 670009 0870 0609777 (UK) AVF Incorporated. 3187, Cornerstone Drive, Mira Loma, CA 91752, USA. 1-800 667 0808 (USA) Orbital Holdings Inc. 3187, Cornerstone Drive, Mira Loma, CA 91752, USA. 1-800 601 8450 (USA) No.
