Owner's manual

ManualsBrandsAVF ManualsFurniturePackage J MC1000 Cart + MC-XL Display Mount

9/16" Wrench

or Socket

M8 Hex Key

(1)

Cart

Cam Bracket (1)

Tube (1)

Tube Bracket (2)

Cam Arm (1)

5/16 Carriage

Bolt (4)

M8 x 20

(8)

1/2" Wrench

or Socket

M6 Hex Key

(1)

M6 x 12

(1)

5/16 Nut (8)

M8 x 12

(2)

Lock

Washer (4)

M6 x 30

(1)

Shelf

Cam Plate (1)

Handle (2)

MC1000-XL

Assembly and mounting Instructions

VIDEO FURNITURE INTERNATIONAL

190 Don Hillock Drive Aurora , Ontario L4G 0G9 www.video-furn.com

Toll Free: 1-877-834-3876 Fax: 1-905-751-1488 Local:905-751-1459

Note:

If you cannot understand these instructions or are concerned about safety of the installation

Contact a qualified contractor or contact VFI at 1-877-834-3876.

Confirm all hardware is included before you begin assembly.

Not all hardware supplied will be used depending on the manufacturer of your display/s.

Thank you for purchasing VFI's MC1000 Metal Cart.

This product was designed for video conferencing applications

and is suitable for single TV configurations.

Supplied Parts:

Supplied Hardware:

Tools required:

Not Included

Page 1

of 6

Hardware

Bag

TV Bracket (2)

Spine

Assembly (1)

Hardware Bag

Base:

Options:

Camera

Hardware

Bag

Summary of content (6 pages)

PAGE 1
MC1000-XL Assembly and mounting Instructions Page 1 of 6 Thank you for purchasing VFI's MC1000 Metal Cart. This product was designed for video conferencing applications and is suitable for single TV configurations. Note: If you cannot understand these instructions or are concerned about safety of the installation Contact a qualified contractor or contact VFI at 1-877-834-3876. Confirm all hardware is included before you begin assembly.
PAGE 2
Page 2 of 6 Attaching Handles Step 1 Align handles with the matching locations on the sides of the cart. Use an M8 bolt and hex key to secure the front side and a 1/2" wrench or socket to secure the back side. 1/2" Wrench or Socket 5/16 Nut (4) Installing Spine Assembly M8 Hex Key M8 x 20 (4) Step 2 Slide the spine assembly into the locations on the top of the cart with the large cover facing the back. Secure in place with an M8 bolt on each side.
PAGE 3
Page 3 of Installing Tube Brackets Step 3 1) Remove the back cover by first loosening the M6 bolts, then sliding upwards and out. 2) Attach tube brackets at a desired height using the provided hardware and 9/16" wrench or socket. (If your TV's mounting locations are 600mm wide install the bar brackets on the inside of the vertical tube.
PAGE 4
Page 4 of 6 Attaching TV Brackets Step 5 1.Place TV face down on blanket or non abrasive surface such as cardboard. 2.Check to see if your TV came with mounting hardware or not. If not,we have supplied the most common hardware. Most displays under 42" will use the M6 bolt. Most 42"+ will use the M8 bolts. See which bolt length you need by hand tightening only. 3.Place TV brackets so you can see the TV mounting holes through the bracket and insert bolt through a multi washer. 4.
PAGE 5
Page 5 of 6 Mounting and Securing TV Step 6 1) Slide TV with attached brackets onto the installed TV bar.   2) Secure in place by tightening the M8 bolts on the back of each TV bracket. 3) Connect all cables including those that will be attaching to the camera. M8 Hex Key Installing Back Cover Step 7 Re-install the back cover and tighten M8 bolts to secure in place. M6 Hex Key VIDEO FURNITURE INTERNATIONAL 190 Don Hillock Drive Aurora , Ontario L4G 0G9 www.video-furn.
PAGE 6
Page 6 of 6 Assembling Cam Bracket Step 8  1) Mount your video conferencing camera onto the cam bracket using contents of the camera bag. Install the cam plate first if you camera requires it. 2) Slide the cam bracket into the cam arm and secure in place with an M6 bolt.  M6 Hex Key Camera Hardware Bag M6 x 30 (1) Installing Cam Bracket Assembly Step 9 1) Slide the assembled Cam Arm into the top of the Spine assembly and secure in place with an M6 bolt.