Manual

ManualsBrandsAVF ManualsFurniturePM-D

Mounting Spine

(1)PM-S

Camera Tongue

(1) PM-S

M6 x 25

(4) PM-S

(+4) PM-D

M8 x 20

(10) PM-S

(+12) PM-D

M8 x 12

(10) PM-S

Mounting Bracket

(1)PM-S

(+1)PM-D

Mounting Base

(1)PM-S

Base Extension

(1) PM-S

TV Bracket

(2)PM-S

(+2)PM-D

M8 x 40

(4) PM-S

(+4) PM-D

M5 x 25

(6) PM-S

(+6) PM-D

Multi Washer

(4) PM-S

(+4) PM-D

M5-M8 Washers

(14) PM-S

(+14) PM-D

Spacer

(4) PM-S

(+4) PM-D

Camera Mount Neck

(1) PM-S

Hex Keys

6,5,4mm

(3) PM-S

5/16 Nut

(6) PM-S

13mm

9/16inch

Wrench or Socket (2) Tape

Measure

Spring Washer

(12) PM-S

(+4) PM-D

M8 Lock Nut

(4) PM-S

(+8) PM-D

Assembly and mounting Instructions

(not supplied)

1.9

TV's sized 32-50+" and weighing no more than 160lbs each.

190 Don Hillock Drive, Aurora , Ontario L4G OG9 www.video-furn.com

Toll Free: 1-877-834-3876 Fax: 1-905-751-1488 Local:905-751-1459

Some larger TV's will fit, Download TV manufacturers specs online,

of 8

Read these intructions start to finish before beginning installation.

Not all hardware supplied will be used depending on the manufacturer of your display/s.

Supplied Hardware:

Supplied Parts:

Contact a qualified contractor or contact VFI at 1-877-834-3876.

(+1)PM-D

(1) in PM-S Bag , (+1) in PM-D Bag

Confirm all parts are included before you begin assembly.

Dual Bracket Support

Tools required:

These products are designed for tabletop mounting of a single or dual plasma/lcd

PM-S and PM-D

VIDEO FURNITURE INTERNATIONAL

If you cannot understand these instructions or are concerned about safety of the installation

max hole location is 700mm wide x 440mm high

Page 1

Note:

2 persons are required to attach plasma/lcd TV's to this mount.

Thank you for purchasing VFI's universal display mounting system.

Note:

You will need the PM-S box in addition

to the PM-D box to assemble a PM-D.

(+)Items only come in the PM-D box.

M6 x 40

(4) PM-S

(+4) PM-D

5/16 Carriage Bolt

(6)PM-S

Large Washer

(6) PM-S

Summary of content (8 pages)

PAGE 1
PM-S and PM-D Assembly and mounting Instructions Page 1 of 8 Thank you for purchasing VFI's universal display mounting system. These products are designed for tabletop mounting of a single or dual plasma/lcd TV's sized 32-50+" and weighing no more than 160lbs each. Some larger TV's will fit, Download TV manufacturers specs online, max hole location is 700mm wide x 440mm high Note: 2 persons are required to attach plasma/lcd TV's to this mount.
PAGE 2
Page 2 of 8 Step 1 Securing the Base to a cart or table 9/16 Wrench or Socket 5/16 Carriage Bolt Mounting Base Part Table/Cart Large Washer Spring Washer Shown Mounting to VFI cart PL3070 5/16 Nut Tighten all 6 nuts securely If your cart/table does not have pre-drilled holes. See Page 8 for optimal placement of base. Remove grommet if present, surface must be flat. Step 2 Adding the Mounting Spine 1. Insert Mounting Spine into Base as shown 2. Add the back bolts first.
PAGE 3
Step 3 Attaching TV Brackets Page 3 of 8 1.Place TV face down on blanket or non abrasive surface such as cardboard. Hex Keys 2.Check to see if your TV came with mounting hardware or not. If not,we have supplied the most common hardware. Most displays under 42" will use the M6 bolt. Most 42"+ will use the M8 bolts. See which bolt length you need by hand tightening only. 3.
PAGE 4
Step 4-D Dual Bracket Support (PM-D only) (PM-S go to Next Page) Page 4 of 8 6mm Hex Key M8 X 20 with Locknut 13mm Wrench or Socket A= B + 4" Bolt to the nearest upper hole. A B Step 4.5-D Locating and Installing Mounting brackets 6mm Hex Key C= (D - 29.5")divided by 2 Bolt to the nearest outward hole. Some tolerance will remain for adjusting. 13mm Wrench or Socket D C Note: You will need the PM-D hardware bag in addition to the PM-S hardware bag to complete this step.
PAGE 5
Step 4-S Mounting Bracket (PM-S only) Page 5 of 8 1.Figure out the location of the bracket. A= B + 4" (see below where to measure B distance) Bolt to the nearest upper hole. 6mm Hex key 2.Make sure to center the bracket. 13mm Wrench or Socket 3.Tighten all 4 bolts. M8 X 20 with Locknut A B VIDEO FURNITURE INTERNATIONAL 190 Don Hillock Drive, Aurora , Ontario L4G OG9 www.video-furn.
PAGE 6
Step 5 Hanging TV's and locking into place Page 6 of 8 PP Note: 2 people should lift and secure the TV as it can be heavy and awkward. 6mm Hex key P L 2 Make sure Bolt clears bracket, TV will tilt until its flush with the mount, Tighten bolt until it catches on the bracket. the TV , First hooking the top of the Mounting Bracket 1 Hang rail then allowing the TV to rest on the rail. 3 PPP PM-D Never leave one TV attached. Always have someone support the attached TV as the other side is hung.
PAGE 7
Step 6 The Camera mount Page 7 of 8 1. Bolt tongue to camera mount neck 2. Insert mount neck into mounting spine until tongue is approximately 1-2" from the top of the TV. 6mm Hex key 3. Bolt camera mount neck into mounting spine. Tongue is now ready for camera. M8 X 12 L2 3 M8 X 12 VIDEO FURNITURE INTERNATIONAL 190 Don Hillock Drive, Aurora , Ontario L4G OG9 www.video-furn.
PAGE 8
Step 7 Finishing Page 8 of 8 TV's hidden for mount visibilty. PM-S PM-D Congratulations! you're done. You will notice you have a bit of hardware left over which you may need in the future. We suggest placing this in a small bag and taping it inside the bottom back of the spine. (A PM-S can be upgraded to a PM-D by ordering a PM-D expansion box) If you have any problems,questions or suggestions, we value your feedback. Toll free 1-877-834-3876 center Optimal placement of base.