IP Kamera 9070IR-PoE User Manual Release Date: 10/20/2009 Manual Version: 1.
Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Kamera 9070IR-PoE was designed for indoor use, the manufacturer responsibility for possible damages caused by outdoor use, especially in the rain. 2. Please use the power adapter provided by the dealer, the manufacturer is not responsibility for the possible damage from using power adapters. 4. Do not shake the IP Kamera 9070IR-PoE in any fashion 5.
Table of Content 1.) INTRODUCTION .................................................................................................................. 5 MINIMUM SYSTEM REQUIREMENTS ................................................................................................. 5 2.) PRODUCT OVERVIEW .......................................................................................................... 6 FEATURES ..............................................................................................
IMAGE SETTINGS ................................................................................................................................ 22 TUNE IMAGE ..................................................................................................................................... 24 NETWORK ................................................................................................................................ 26 NETWORK .....................................................................
1.) Introduction The IP Kamera 9070IR-PoE provides reliable, high quality solution to IP Kameras. Its distinctive 720P HD quality picture, Tri-mode video capability, built in SD memory storage, RTSP broadcasting capability, internal microphone and many more functions makes this small device very powerful and unique. The built in web server of the IP Kamera 9070IR-PoE will allow the IP Kamera to be viewed from any remote locations around the world while bringing ease of mind.
2.) Product Overview Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. Tri-Mode Camera (MPG4-1/MPEG4-2/M-Jpeg) Advance Motion detection trigger AVI /Jpeg save on FTP / SD card or Email 3 layers (Admin, Operator, and User) Password protected Resolution from CIF 352x192 up to HD 1280x720P Supports NTP protocol to get correct time schedule. 1/2.5” Advance CMOS sensor, with highly sensibility for quick response insufficient lighting.
Package Contents 1.) 9070IR-PoE Unit x 1 with Lid 3.) 9070IR-PoE Installation CD 4.) AC Adaptor (AC adaptor will be included and will correspond to the countries power standards) Specs: Input: 100-250Vac /47-63Hz, 1A Output: 12Vdc/1A Max: 12W 5.
3.) Interface Description Cable Description Cables DC 12 V Power Input: Plugs in the Power Adapter to the DC 12V Card PoE RJ45 Ethernet: Plug in the RJ45 Ethernet cable to the Ethernet PoE Specifications: 802.3af PoE Reset Button: Reset to Manufacturer Default: Hold Reset button for 5-10 Seconds and the device will reset to manufacturer default. Video Out: The Video out requires a BNC connector to output video to a different source. Embedded SD Card Built in 2 GB SD Memory Card. 4.
Please see the image below for reference. Internet Accessible Setup The internet connection can be setup in two main ways so that the 9070IR-PoE can be accessed through the internet The network uses a Router/Firewall to connect each device to the internet In this case, the 9070IR-PoE will need to be port forwarded on the router so that it can accessed by the internet. For example 9070IR-PoE IP Address: 192.168.1.
On the router that is being used port forwarded (port triggered) IP Address 192.168.1.882 and port 9070. For this section you may be required to refer the user manual for the router due to the fact that each router has a different way of setting up the device. By using static IP Address provided by the ISP. In this case, the 9070IR-PoE is being connected to the internet through a hub, which is different from a router.
2.) Once the CD has started go to the IP Kamera & IP Video Server section. Then under IP Kamera 9070IR-PoE download the two software. a. b. IPEdit - Device search tool Surf 16 CH – 16 Channel DVR, Monitoring, & Recording Software 3.) Once installation is complete please double click the IPEdit to configure and search for the device. Installing VLC Codec The files that are recorded by the 9070IR-PoE requires VLC codec to be able to view the recordings.
Default Password: 12345678 1.) Double click on the IPEdit icon to run the program. 2.) Open IPEdit and any device in the same network should automatically be detected and listed in the local devices sections. Note: Hit the Rescan button and wait about 1 minute, if the device is not showing up. Setup the Device: All devices will need to be on the same network if not the device cannot be accessed and will not be detected.
1.) Click on the REF button, and wait a few seconds. IPEdit will automatically detect the network settings and setup the device. 2.) Once settings have been detected hit the apply button to apply the new settings. 3.) Hit yes to confirm and Enter the login and password for the Device to Approve changes 4.) Then hit the rescan button on IPEdit to confirm the changes have been made. Custom Setup (Advance Users) 1.
2.) To setup the device, type in the correct Gateway and IP Address. The Gateway Address: The gateway address can be obtained in Windows under the network connections page IP Address: Make sure the first 3 sections of the IP Address matches the gateway address. Example: Gateway Address – 192.168.1.1 IP Address – 192.168.1.xxx 3.) Once the Default Gateway information has been obtained, enter the correct information into IPEdit and hit the submit button.
4.) Then hit the rescan button on IPEdit to confirm the changes have been made. IP Service How to use IP Service on IPEdit: IP service allows the user to directly connect to the device through the internet without having to remember long confusing IP Address. Instead the user only needs to remember the name of the device. Then connect to IP Service, type in the device name, and directly connect to the device. Note: To find IP Kamera 9070IR-PoE select Server 2 on IP Service 1.
4.) Double click on the device name and an Internet Explorer window will appear directly to the device. Note: It is crucial to have the IP Address of the device port forwarded from the router that is being used so the device can be connected from any location. Refer to the routers user manual on how to port forward devices. 6.) Web Interface Connecting to the 9070IR-PoE Once the 9070IR-PoE has been setup correctly, connect to the login page. An Internet Explorer browser screen pop up with the login screen.
2.) Right click on yellow bar and install the activeX controls. 3.) Then click the install button and install the active X controls.
4.) Once activeX controls have been installed the video feed will show on the screen Note: If no active x controls are showing up, please go to internet explorer and enable activeX controls.
The Control Console Section of the webpage. In this The IP Kamera 9070IR-PoE Control Console starts in the section navigate to the other options and settings of the 9070IR-PoE Live Video: The Live Video section allows the user to view the camera, change resolution views, Image: The Image section allows the user to adjust the image settings, including recording / viewing codec, frame rate, image tuning, brightness, contrast, saturation, and etc.
Live Video The Live video section of the IP Kamera 9070IR-PoE is where the user can view the video of the device. From here resolution, record onto current pc, take a snapshot, zoom, and detect motion detection settings can be changed. Type and Zoom Type: The type function sets the streaming format for the IP Kamera 9070IR-PoE. Select from the following type of resolutions depending on the format type set in the image settings.
Active Record Active Record: Active record will show up when the device is actively recording. Active recording functions like motion detection, scheduler, or an alarm will set off this automatic recording. When active recording is not activated it will look like the picture below When the active recording function is activated it will light up in red. Record Record: The record button on the 9070IR-PoE when pressed will record the live video feed and save the video into the computer viewing.
2.) The live view mode will switch to the snapshot mode and the current screen will be displayed 3.) To save the picture right click on the picture and select the option save picture as. Then browse the computer and save the picture to the directory of choice. 4.
Camera Name: Select a camera name for the device and then hit submit \ Video Codec: Resolution: Resolution (MPEG4+MPEG4+JPEG): M4:720P,M4:CIF,JPG:352 (MPEG4+JPEG): M4:VGA,JPEG:VGA (MPEG4+JPEG): M4:720,JPEG:352 (MEG4+MPEG4): M4:720,M4:CIF (Single MPEG4): M4:720 Color System: Select the broadcasting color system that pertains the country. NTSC/60Hz PAL/50Hz Rate Control: Select the most suitable Bit Rate Control.
M-JPEG Settings: The available Quality settings and FPS for the M-JPEG settings are shown below M-JPEG Quality Settings High Medium Low M-JPEG Frame Rate Settings 30 FPS 15 FPS MPEG4-1 Bit Rate: Select a value from 64~8000. FPS: Select a FPS from 30fps, 15fps, or 7.5fps 7.5 FPS 3 FPS 1 FPS MPEG4-2 Bit Rate: Select a value from 64~8000. FPS: Select a FPS from 15fps or 7.5fps Enable EPTZ: The EPTZ on the IP Kamera 9070IR-PoE a virtual EPTZ function.
White Balance: Select from the following options auto, indoor, or outdoor Day and Night: Select the mode Day or Night TV Output: Select the mode enable or disable to output to a T.V Binning / Skipping mode: Binning enables low light-light performance.
Network Network The network section sets up the network information for the IP Kamera 9070IR-PoE. IP Address: Actual IP Address of the device can be found here LAN IP Address: Local Area Network Address.
FTP The FTP section of the IP Kamera 9070IR-PoE setups the FTP saves video clips on FTP. FTP Server: Enter the FTP server address here User Name: Enter the FTP Username Password: Enter the FTP Password File Upload Path: Enter the upload path of the FTP Server SMTP (Outgoing E-mail Server) Enter the SMTP E-mail server information here.
SNTP Server: Enter the SNTP server address Time Zone: Enter the corresponding time zone Automatically adjust for daylight saving time: Check this section for daylight saving time to be implemented automatically. IP Service IP service allows connects to the device directly without having to remember a long IP Address. Enter the device name into IP Service and anyone can find their device as long as the port forwarding has been setup. In the IP service section this feature can be disabled.
Set the date and Time of the device here. The Local Time: The local time corresponds to the current time of the IP Kamera 9070IR-PoE. Time Setup: Setup the current time of the device here 1.) Set Manually: Set the time manually 2.) Synchronize with Computer Time: Synchronize the time with the current computers time 3.) Synchronize with SNTP: Synchronize with SNTP Time Stamp The time stamp adds a time to the live video. When a recording is made this time stamp will show up with in the video file as well.
The user setting creates and removes users for access to the IP Kamera 9070IR-PoE. Authority: Select one of the following options: Admin: Admin can operate all functions in Web interface. As well as, add or delete any user’s account. Operator: Operator can operate all functions in Web interface except user Add/Delete. Viewer: Viewer can only monitor the Web interface, but cannot operate all function and set parameters. Light To disable the IR lighting check in the disable IR box.
Update To update the device go to the update section. Here the Current Version description is available. To update the device: 1.) Browse for the correct update file. 2.) Hit the update button. 3.) A message will appear, reminding the user not to disconnect when updating. 4.) Please view the bar on the bottom of internet explorer to make sure that the device is updated. 5.) When update is complete a new screen will appear then connect back to the device. 6.
Event Log Application The Application Section setups the Video File information, FTP, SD Card, SMTP - 32Ref#90020326K0709
Setting Snapshot Path Select the snapshot path to the destination where snapshots will be saved. Video File Select the Video File format that the device will record in. 1.) Avi Duration: From the drop-down list, select the length of an AVI file. 2.) Avi Format: MPEG4 (720) MPEG4 (CIF) 3.) Hit the submit button to confirm new settings. FTP In the FTP section, select the file format that will be used for FTP transfer. Note: 1.) Before using the FTP function, set the FTP server information.
SD Card File Format: Select the video format to save into the SD card Split Filename Type: Select the format to save the files in the SD card. Select from: Name by Index: Creates file names according to index. Name by Time: Creates file names according to time. Split File Size: Select the size of each file that will be saved into the SD. Select from the following: None, 10mb, 25mb, 50mb, & 100mb.
SMTP In the settings section, find the SMTP information by clicking on the SMTP tab. Here the current SMTP Server information and email address are available. Storage Settings Select the file format for IP Kamera 9070IR-PoE to send in. Select from MPEG4 or MJPEG. Record Schedule The schedule allows the user to select days and times to schedule for automatic recording. Pick a day from (Sunday – Saturday) and also a option for Everyday. To schedule automatic recording: 1.
Schedule Record Schedule Record allows selects where the schedule will record the video files to. Schedule Record – Upload via FTP: Saves schedule recordings into FTP Schedule Record – Save into SD Card: Saves schedule recordings into SD Card Alarm Enable Alarm Enable Alarm – Lost Ethernet Connection: Save into SD Card: When Ethernet connection is lost the device will automatically save into the SD card.
Motion Detection To enable motion detection: 1.) Select Enable in the motion detection option. 2.) Select the desired sensitivity of choice a. Pick from Lowest, Low, Medium, High, Highest b. The threshold can be selected from (1-99) 3.) Once the settings are set, on the window screen click on the picture where motion will be detected. Double click on the selected areas to remove the choice. Right click on the window screen for more options 4.
EPTZ-Set The EPTZ allows the viewed image to be Pan, Tilt, & Zoom. To activate this feature EPTZ must be enabled in the Image section of the 9070IR-PoE. Note: When EPTZ Controller is activated Video Codec mode will be switched to MPEG4 & M-Jpeg when disabled the codec will be set on Mpeg1, Mpeg2, & M-Jpeg.
SD Card To access the files on the SD card simply press the SD Card button screen. To play the file directly: Simply just press on the file of choice. on the live view To Delete: Simply press the delete link on the SD card section 7.) Controlling the Device CGI HTTP Commands Http commands are command lines that execute commands to the device from a web browser, software, or code. The basic commands are provided below.
http://ipaddress:port/vb.htm?internetip=ipaddress Ex. http command: http://192.168.1.192/vb.htm?internetip=192.168.1.191 Change Port: This command changes the Port of the IP Kamera 9070IR-PoE http://ipaddress:port/vb.htm?httpport=portnumber Ex. http command: http://192.168.1.192/vb.htm?httpport=1025 Change Subnet Mask: This command changes the Subnet Mask of the IP Kamera 9070IR-PoE http://ipaddress:port/vb.htm?subnetmask=subnetmask Ex. http command http://192.168.1.192/vb.htm?subnetmask=255.255.0.
How to setup VLC media player & Open a network stream Note: Before using RSTP you must port forward your router to the following port numbers. For 1280 x 720P (Mpeg4-1): Port forward to 554 If Port forwarding (Mpeg4-2): Port forward to 8554 1.) Open VLC media Player 2.) Click on Tools > Preference 3.) On the bottom of the screen click the Reset preference button. 4.) On the bottom left hand side of VLC select the all under the show settings area. 5.
10.) Type in the RTSP address of your device For Mpeg4 Stream1 : rtsp:///mpeg4 For Mpeg4 Stream2 : rtsp://:8554/mpeg4 Example: rtsp://122.116.137.123/mpeg4 Hit the play button and wait a few seconds for the program to start streaming.
- 43Ref#90020326K0709
9.) Using CNT with Surf16 CH CNT makes connecting to the IP Kamera 9070IR-PoE a very simple task. Surf 16 CH a multi-device DVR monitoring software easily allows the user view the 9070IR-PoE. Follow these simple steps: Finding the MAC Address There are two ways to find the MAC address in IPEdit. *Note: IP Server must be enabled on the device’s webpage. By default IP Server is enabled. Find MAC Address in LAN Using IPEdit 1.) In IPEdit, highlight the device that is being used.
3.) Do not forget to enter the password and login. 10.) Frequently Asked Questions (F.A.Q) Q1: Why can’t I view the video files that I have recorded, nothing is playing? Ans: VLC Codec, download VLC Codec from their website at: http://www.videolan.org/ Q2: How do I reset the device to manufacturers default values? Ans: On the back of the device there is a reset button, hold down the reset button for more than 7 seconds. Then give the 9070IR-PoE a 1 minute to restart.
