Sheet-fed Duplex Scanner User’s Manual Regulatory model: FT-0604H Avision Inc.
Trademarks Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows and MS-DOS are trademarks of Microsoft Corporation. IBM, PC, AT, XT are registered trademarks of International Business Machines Corp. Other brands and product names herein are trademarks or registered trademarks of their respective holders. Copyright All rights reserved.
User’s Manual FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication.
EC Declaration of Conformity According to EN45014 Manufacturer's Name: AVISION INC. Manufacturer's Address: No. 20, Creation Road I, Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C.
User’s Manual System Requirements Windows ¾ IBM compatible PC 586, Pentium or higher ¾ Microsoft Windows 98 / 98SE / Me / 2000 / XP ¾ USB port 2.0 (compatible with USB 1.
Table of Contents 1. Introduction.............................................. 1-1 2. Scanner Installation.................................. 2-1 2.1 2.2 2.3 3. Completing Your First Scan ....................... 3-1 3.1 3.2 3.2 4. Installing the Input Paper Tray ..................... 2-2 Installing the Output Paper Tray................... 2-4 Installing the Scanner Driver and Cables ....... 2-6 2.3.1 Connecting to Power......................... 2-6 2.3.2 Turning on the Scanner ....................
User’s Manual 4.4 4.5 4.6 4.7 4.8 5. Using the Buttons...................................... 5-1 5.1 5.2 5.2 6. Cleaning the ADF ....................................... 6-1 Cleaning the Calibration Area ....................... 6-3 Replacing the Snap-in Pad Module ................ 6-4 Troubleshooting ........................................ 7-1 7.1 8. Installing Button Manager............................ 5-2 Checking the Button Configurations Before Scanning..........................................
User’s Manual 1. Introduction Congratulations on your purchase of the color sheet-fed image scanner. With this scanner, you can quickly scan documents in duplex (double-sided) mode to increase productivity. Before you install and operate the new scanner, please take a few minutes to read through this manual. It provides proper instructions for you to unpack, install, operate and maintain the scanner. The following figure indicates the package contents. Please check all the items against your checklist.
1 2 3 5 4 Note: 1. 1. 2. 3. 4. 5. Scanner Main Unit ADF Paper Tray ADF Output Paper Tray USB Cable Power Adapter & Power Cord Only use the AC adapter HEG42-240200-7L (made by HiTron) included in the machine. Using other AC adapters may damage the machine and void the warranty. The suitable power supply cord will be provided and evaluated when national approval. 3. Please unpack the packing carefully, and check the contents against the checklist.
User’s Manual 2. Scanner Installation Precautions Keep the scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause damage to the unit. Do not install the scanner in a humid or dusty place. Be sure to use the proper AC power source. Place the scanner securely on an even, flat surface. Tilted or uneven surfaces may cause mechanical or paper-feeding problems. Retain the scanner box and packing materials for shipping purposes.
2.1 Installing the Input Paper Tray 1. Pull the ADF Release button to open the front cover. ADF Release Button Front Cover 2. Insert the pin with a inclined plane on the right side of the Input Paper Tray to the hole on the rear of the scanner as illustrated.
User’s Manual 3. Use your left thumb to press the place near the pin with a inclined plane of the other side of the Input Paper Tray and then insert the pin to the hole of the scanner as illustrated.
2.2 Installing the Output Paper Tray 1. Insert the smaller pin of the left side of the Output Paper Tray to the hole on the front of scanner as illustrated.
User’s Manual 2. Use your thumb to press the place near the pin of the other side of the Output Paper Tray and then insert the smaller pin to the hole on the scanner as illustrated.
2.3 Installing the Scanner Driver and Cables Note: 1. The Windows system CD may be required when installing on some PC’s. 2. To ensure your computer can identify the USB scanner, please install scanner driver first before connecting the scanner to your computer. 2.3.1 Connecting to Power Plug the small end of the power adaptor into the power jack of your scanner. Insert the other end to an appropriate power outlet.
User’s Manual 2.3.2 Turning on the Scanner 1. Press the Power Switch button on the front panel, the Power LED will flash. When it is finished and ready to scan, the LED indicator will stop flashing and become steadily on. To turn off the scanner, press the Power Switch button for about 3 seconds, the Power LED will be off. Power Switch 2.3.3 Installing the Scanner Driver 1. Place the supplied CD-ROM onto your CD-ROM drive. 2. The software installation graphic appears. If not, run “setup.exe”.
3. Choose Install Scanner Driver to install the scanner driver. 2.3.4 Connecting to Computer 1. Connect the square end of the USB cable to the USB port of your scanner. Connect the rectangle end to the USB port of your computer. USB cable 2. The computer should detect a new USB device and prompt a “New Hardware Found” message.
User’s Manual 3. In Windows 98SE, Windows ME, or Windows 2000, confirms that the “Search for a better driver.” is selected and click the “Next” button. In Windows XP, click the Next button to continue. When the XP certification screen appears, click Continue Anyway to complete the installation. 4. When the Finish dialog is prompted, click the Finish button. 5. Click “View Manual” to view or print the detailed user manual for the scanner and bundled applications respectively.
User’s Manual 3. 3.1 Completing Your First Scan Loading Your Paper 3.1.1 Notice on Using the ADF Before using the ADF, please make sure that your paper meets the following specifications: • Document(s) can range in size from 3.5 by 2 inches • Document(s) can range in weight from 16 to 34 lbs (60 ~ 127 g/m2) • Document(s) should be square or rectangular and in good condition (not fragile or worn). • Document(s) should be free of curl, wrinkle, tears, wet ink, or punch holes.
3.1.2 Placing Your Document in the Input Paper Tray Fanning Your Document Standard paper size should feed easily through the scanner. To avoid occasional paper jam when automatically feeding multiple documents, loosen the paper before loading. Document feeding Place your document with the text face down on the ADF Paper Tray. Align the two sides of the document with the slide guides. Please note that the ADF Paper Tray can hold up to 100-page (60 ~ 65 g/m2)document at a time.
User’s Manual 3.2 Verifying Your Scanner Installation To verify if your scanner installation is correct, Avision provides you a useful test program called Avision Capture Tool. With this tool, you can perform simple scans and view the captured images. In addition, it helps you complete your scan at a rated speed. The following procedure describes how to verify your scanner installation.
Fit Actual Page Size Setup Scan File Format Save File Path 3. Choose your desired file format from the File Format drop down list box. (Default is BMP, other choice includes TIFF, GIF, and JPEG.) 4. Type your desired folder name and file name in the File Path box. (Default is C:\My Scan\Image.) Note: If you do not wish to save the scanned image, deselect the Save button since default is Save Enable. In this case, the thumbnail view will be disabled.
User’s Manual Image Selection Box 6. From the Image Selection Box, choose your desired image type for your scanned image. (Default is Front B&W) If you have a duplex scanner, choose Front and Rear to scan both sides of your document. 7. Click OK to quit the Scanner Properties dialog box. (To learn more details about the Scanner Properties dialog box, please see the subsequent chapter, Using the Scanner Properties Dialog Box.) 8.
Status Bar Fit Page View Thumbnail View 11. You can view the scanned image in Fit Page ( Actual Size (100%) button ( at the right side. ) or ) from the Viewing toolbars 12. Click the Close box or Quit from the File menu to exit the Scan Validation Tool.
User’s Manual 3.2 Scanning with Image Editing Software The scanner driver is not a stand-alone program, it has to be started from within a TWAIN-compliant software application and then the scanner driver is able to scan and load the image to your computer. The command to start the scanner driver may vary due to different software applications. 1. 2. Start a TWAIN compliant software application such as Roxio PhotoSuite which is bundled in the CD. Click Get>Scanner (TWAIN). 3.
7. Click Exit to return to the main screen and click Open Library and Photos at the upper-right corner to open your scanned image.
User’s Manual 3.2.1 A Glance of the Scanner Properties Dialog Box 1 2 3 4 5 6 7 8 1. Tab Options Choice: Image, Compression, Color Dropout, Paper, Options, Settings, Information. 2. Image Choose your image type and the side of Selection Box document you wish to scan. Options vary based on type of scanner. 3. Brightness: Adjust the brightness level from –100 to +100. 4. Contrast Adjust the contrast level from –100 to +100. Determine the quality of the scanned image. 5.
User’s Manual 4. Using the Scanner Properties Dialog Box The Scanner Properties dialog box allows you to configure the scanner’s settings. It consists of several tabbed windows each of which will be described in this chapter.
4.1 Buttons on the Scanner Properties Dialog Box The buttons on the Scanner Properties dialog box Buttons Description Defaults Click the Defaults button, the factory default settings will be shown on each tab. Scan After all the scan settings are satisfactory, click the Scan button to start scanning your document. Close Click the Close button to leave the Scanner Properties dialog box.
User’s Manual The following table shows the default settings： Tab name Image Default settings Image：Front B&W Binarization：Dynamic Threshold Resolution：200 dpi Invert：Blank on White Scan Source：Auto Document Feeder Threshold：None Brightness：None Contrast：None Compression None Color Dropout None Paper Cropping：Automatic Deskew：Yes Orientation：Portrait OverScan：0.
4.2 The Image Tab The Image tab allows you to choose the front side and (or) the rear side of your document, the type of image, and to set several basic scan settings. Note that except for the resolution, you can set individual scan settings for the front side and the rear side. For example, all settings in the Image tab, Compression tab, Color Dropout tab can be set individually for the front and the rear side.
User’s Manual 4.2.1 The Image Selection Box The Image Selection box includes the image type and document side option. If you wish to scan both the front side and the rear side of your color document, you can check both Front Color and Rear Color at the same time. Note the options vary based on type of scanner.
Example 2：Scanning a two-sided color document, one in B&W(Drop Blue Color：Threshold：10, Background： 79), the other in color Side/Image Selection Image Type Color Gray B&W B&W Front Rear Description Choose Color if you wish to scan a color image for your original in color. Choose Gray image if your original contains actual shades of gray. Choose B&W if your original contains only text pencil or ink sketch.
User’s Manual 4.2.2 Other Image Options Binarization This is the process of converting a grayscale or color image to a bi-tonal image. There are several different methods of performing this conversion. Two of the options are Dynamic Threshold and Fixed Processing. Dynamic Threshold: Selecting Dynamic Threshold allows the scanner to dynamically evaluate each document to determine the optimal threshold value to produce the highest quality image.
Threshold Used to convert a grayscale image to a bi-tonal image. The value ranges from 0 to 255. A low threshold value produces a lighter image, and can be used to subdue backgrounds and subtle, unneeded information. A high threshold value produces a darker image, and can be used to help pick up faint images. Adjust the threshold setting by dragging the Threshold sliding bar to the left or right to achieve the desired threshold setting.
User’s Manual Brightness Adjusts the lightness or darkness of an image. The higher the value, the brighter the image. Drag the slider to the right or left to increase or decrease the brightness. Contrast Adjusts the range between the darkest and the lightest shades in the image. The higher the contrast, the bigger the different grayscale. Drag the slider to the right or left to increase or decrease the contrast. The range is from –100 to +100. The range is from –100 to +100.
Resolution A good control of the resolution results a good detail of an image that scans. The resolution is measured by dots per inch (dpi). Normally, the greater the dpi number, the higher the resolution and the image file size. Be aware that greater resolution takes more time to scan, and more disk space for the scanning image. For your information, an A4 size color image scanned at 300 dpi at True Color mode consumes approximately 25 MB of disk space.
User’s Manual Invert Reverses the brightness and the colors in the image. The default setting is Black on a White background. Reverse mode is White on a Black background. For color images, each pixel will be changed into its complementary color at the command of Invert.
Scan Source Choice: y Auto Document Feeder: Used to scan multiple pages. y Flatbed: Used to scan a single page. For example, pages from newspaper clipping, paper with wrinkles or curls. y Flatbed (book): Used to scan several inside pages from book. y Automatic: Allow the scanner automatically set its scan source. If Automatic is selected and there is document in both the auto document feeder (ADF) and the flatbed, then the scan source will be automatically set to ADF.
User’s Manual 4.2.5 Scanning B&W images The following options are available for scanning B&W images.
4.2.6 Editing Profiles The Scanner Properties dialog box allows you to change and save your frequently used scan settings into a profile. You can edit these profiles by renaming or deleting them. To add a new profile, 1. 2. Customize your settings. (For example, change your resolution, image type, cropping method, scan size, or other scan settings.) Click the Image tab and then choose “Profiles” to prompt the “Edit Your Profile” dialog box. 3.
User’s Manual To load a profile, 1. From the Image tab dialog box, choose your favorable profile from the “Profiles” dropdown list box. 2. Your favorable profile will be immediately loaded and displayed on Scanner Properties dialog box. To delete a profile, 1. From the Image tab dialog box, click “Profiles” to prompt the Edit Your Profile dialog box. 2. Choose the profile you want to delete from the dropdown list box. Click “Delete”.
To rename a profile, 1. From the Image tab dialog box, click “Profiles” to prompt the Edit Your Profile dialog box. 2. Choose the profile you want to rename from the dropdown list box and then click the Rename button. 3. Enter new name for the profile. 4. Choose “Save” to save the new profile or “Cancel” to quit. Note: The preset default profiles include Flatbed, Simplex-B&W, 200 dpi, Simplex-Gray, 200 dpi, Simplex-Color, 200 dpi, DuplexB&W, 200 dpi, Duplex-Gray, 200 dpi, Duplex-Color, 200 dpi.
User’s Manual 4.3 The Compression Tab The Compression tab allows you to compress your scanned image and choose the level of compression. Bi-tonal images are normally compressed using CCITT standard called Group 4 (G4). Color and grayscale images are often compressed using JPEG technology. Move the JPEG Quality slider to the right or left to increase or decrease the level of compression. Note the greater the compression level, the lower image quality. Default is 50%.
The Compression tab dialog box 4-18
User’s Manual 4.4 The Color Dropout Tab 4.4.1 Color Dropout Selection Color Dropout tab allows you to drop either of the red, blue, or green color in your scanned image. If your image contains red color watermark or background, choose the R (Red) channel then any red watermark or background will be removed. This feature is used to sharpen your text when using OCR (Optical Character Recognition) software. Note that this function supports only black & white and gray images.
4.4.2 Other Color Dropout Options Advanced Processing provides two options that can adjust your scanned image in the best optimal result. Filter Threshold This value is used to determine the color which will be dropped out. A lower value will drop more of the selected color out, while a higher value will leave more of the selected color in. Background Level The pixel which is higher than the background value will be adjusted to the lightest point.
User’s Manual Remove Blue, Threshold: 20, Background: 255 Remove Blue, Threshold: 20, Background Level: 210 4-21
4.5 The Paper Tab The Paper tab allows you to define values relating to image output (i.e., Auto Crop or not, Scan Area, OverScan, Multi-Feed Detection).
User’s Manual 4.5.1 Cropping Cropping allows you to capture a portion of the document being scanned. Choice: Automatic, Fixed to Transport, EOP (End of Page) Detection. Options Description Automatic Automatic adjusts the cropping window according to different document sizes. Use this option for batches of mixed-sized documents. Fixed to Transport This feature allows you to define the area or zone to be imaged. Use for batches of same-sized documents.
The following options are only available when Fixed to Transport is selected. y X-Offset — the distance from the left end of the scanner to the left edge of the scanning area. y Y-Offset — the position from the top end of the document to the top end of the scanning area. y Width — the width of the scanning area. y Length — the length of the scanning area. y Center: automatically calculates the x-offset for centerfed feeding based upon document size selected.
User’s Manual Example： Redefine your scan area ( x-offset: 2.25 inches；yoffset:1.
4.5.2 Other Paper Selection Deskew Use this option to automatically deskew a document. Note: If the skew angle is too great, some of the image may be cut off. Scan Area Choose your desired paper size with the drop-down list box. Or you may select a custom paper size by clicking the Scan Area box and then click Add to include in the choice. Choice: None, US Letter- 8.5”x 11”, US Legal – 8.5” x 14”, ISO A4 – 21 x 29.7 cm, ISO A5 – 14.8 x 21 cm, ISO A6 – 10.5 x 14.8cm, ISO A7 – 7.4 x 10/5 cm, ISO B5 – 17.
User’s Manual Choose “Unlimited” if you have a batch of long page document with unknown length. Choose “Enter Length” to enter the length and width of your documents or your desired scan size on documents. This is useful when you have a batch of documents with the same scan size or a batch of same-sized documents. OverScan Overscan allows you to add a specific margin at top and bottom or right and left (Options vary based on the type of scanner) of the edge of the image.
Example：Additional Length Detection：Set Additional Length to be 2.02 inches 2.02” There are two options available if Multi-Feed is detected. z z Stop Scanning after Multi-Feed If this is selected, the scanner will stop the feeder if multifeed is detected. Sound Alarm on Multi-Feed: If this is selected and a wave file is added, the scanner will produce a sound alarm if multi-feed is detected.
User’s Manual How to add the sound alarm： 1. Click the Browse button on the right side of the speaker icon. The Open dialog box appears. 2. Choose your wave file. 3. Click the Open button. The wave file is added. Units Defines the primary measurement system. Inches, Millimeters, and Pixels are available.
4.5.3 Relative to Document Relative to Document: (used for batches of same-sized documents) This option allows you to crop different areas on your documents and deliver these images in B&W, Gray, or Color separately. For example, there are applications which require you to store the entire document in B&W and a part of the document in color to save storage space. This is useful for documents where a photograph, or signature appears in a consistent area on the document such as resumes, and so on.
User’s Manual 3. Click the Preview tab to display the Preview window. A black rectangular box appears to indicate the max. scan size your have just selected. The selected image The Image Selection Box A black rectangular box 4. Click the Preview button to view the entire image in low resolution to correctly crop your relative scan area. The Preview Image The Preview Button 5. Select image type from the Image Selection box. The selected image will appear in highlighted color.
A Cross Sign 7. 8. The Relative Area Check the B&W image from the Image Selection box to scan the entire document. Click the Scan button to start scanning the document in two image types and sizes. (See the result in below.
User’s Manual 4.6 The Options Tab The Options tab allows you to set following additional image processing settings.
Flip Side Rotation Select “fanfold” to rotate the image of the reverse side to 180 degrees. This is applied to double-sided document which are viewed in portrait are sometime fed into the scanner in landscape or vice versa. Choice: Book, Fanfold. If “Book” is selected, the image of the reverse side will not be rotated.
User’s Manual Rotate Image Choose the rotation angle from the drop down list if you wish to rotate your scanned image. Choice: None, 90°CW(clockwise), 90°CCW(counter clockwise), 180°. Original Rotate 90°CCW Blank Page Removal Rotate 90°CW Rotate 180° Check if you wish to remove the blank page and move the slider to the left or right to your desired threshold.
Edge Fill Check White or Black if you wish to add white or black edge on the border of your scanned image. Enter the value from 0 to 5 mm. Default value is 0. Edge Fill: 5mm (Black) Original Image Control Option Check the Mirror box if you wish to reverse the right and left side of your image.
User’s Manual Background Setting This option allows you to set your scan background. Choice: White Background, Black Background. *This option varies based on type of scanner and is available for the front page in the ADF (auto document feeder) only. For the rear page, only the white background is available.
4.7 The Setting Tab The Setting tab allows you to set the following settings: The Setting tab dialog box Energy Saving Control Check the Enable Energy Saver box and move the slider to the right to set the amount of time to start the energy saver after your last action. The range is from 1 to 720 minutes. The default is 15 minutes.
User’s Manual Batch Scan Setting •Batch Scan To increase the scanning speed, the scanner first scans a few pages of your document and then sends these scanning data to the application. Therefore, during scanning, the numbers of pages been scanned on the scanner is somehow different with the numbers of pages displayed on your computer screen. Choose this mode if you wish to complete your scanning task at the fastest speed.
Show Warning Message Check to show the warning messages such as “ADF pad count exceeds 50,000 scans (the number varies based on type of scanner). Please replace the ADF pad and reset the pad count.” Save Settings after Closing Check to save your scanner properties settings after leaving the dialog box. Next time when you open the Scanner Properties dialog box, the previously saved settings will be shown.
User’s Manual 4.8 The Information Tab The Information tab displays the following system and scanner information. The Information tab dialog box The “Report” button： If you encounter any error message while using the scanner, click the Report button. A report.txt file (C:\AVxxx) will be generated. Please send this file to the nearest service center for trouble shooting.
The “Reset Pad Count” button」： After scanning approximately 50,000 pages (the number varies based on type of scanner) through the Auto Document Feeder (ADF), the ADF pad may be worn out and you may experience problems with document feeding. In this case, it is highly recommended to replace the ADF pad with a new one. (Please refer to the manual for proper replacing procedure.) For ordering the ADF pad, please consult your nearest dealer.
User’s Manual 5. Using the Buttons The following picture shows the 4 buttons and 1 function screen on the scanner.
5.1 Installing Button Manager To use the buttons on the scanner, you need to install the Button Manager. To ensure the Button Manager work properly, please FIRST install Button Manager before installing the scanner driver. Installing the Button Manager is easy. Insert the supplied CD to your CD-ROM drive and follow the instructions on the screen to complete the installation of the Button Manager.
User’s Manual 3. The Button Panel shows the first five scanning buttons. Right-click the button (function) you wish to check. The Button Properties window appears. Click to select options or setting. The button number and name. The scan settings for the selected button. (in this case button #1). The file format of the scanned image. (*The options vary based on type of scanner.) The destination application. (This is the application that opens after you have finished scanning.
5.2 1. 2. 3. 4. Scanning From One Touch of the Buttons Adjust the paper guide for the width of paper and load the document with their tops into the automatic document feeder. Check the number on the LED screen to ensure if you are selecting the proper scan settings and destination application. (For example, if you want to scan with button #4, which open roxio PhotoSuite and display the scanned image in the main window of roxio PhotoSuite, the LED screen should show 4). Press the Scan button on scanner.
User’s Manual 6. 6.1 Maintenance Cleaning the ADF From time to time the pad assembly and feeding rollers may become contaminated with ink, toner particles or paper dust. In this case the scanner may not feed documents smoothly. If this occurs please follow the cleaning procedures to return your machine to its original state. The Cleaning Procedures 1) Soak a clean lintless cloth with some isopropyl alcohol (95%). 2) Press the ADF Release button on the upper. Open the front cover slightly to the left.
ADF Pad Module ADF Roller ADF Pad ADF Roller 6-2
User’s Manual 6.2 Cleaning the Calibration Area 1. 2. 3. Press the ADF Release button. Open the front cover to the left. Wet a clean lintless cloth with some isopropyl alcohol. (95%) Wipe the glass and the white area as illustrated in below from side to side to rid the dust or dirt.
6.3 Replacing the Snap-in Pad Module After scanning approximately 20,000 pages through the ADF, the pad may be worn out and you may experience problems with document feeding. In this case, it is highly recommended to replace the pad module with a new one. For ordering the pad module, please consult your nearest dealer and follow the procedure below to replace it. Disassembling Procedure 1. 2. 3. Use your left thumb to pull the ADF Release Button on the top of the ADF (auto document feeder) unit.
User’s Manual 7. Troubleshooting 7.1 Clearing a Paper Jam In the event of a paper jam, follow the procedures below to remove the paper: 1. Pull the ADF Release Button on the left side. Gently open the front cover to the left. 2. Carefully pull the paper out of the ADF unit. 3. Close the scanner front cover. Your scanner is now ready to use.
User’s Manual 8. Specifications All specifications are subject to change without notice. Model Number： FT-0604H Scanner Type: A3 sheet-fed Scanner Optical Resolution: 600 dpi * 600 dpi Scanning Modes: Black & White Gray Color ADF Capacity: Up to 100 pages Document Size: A3, Letter, legal, A4, B5, A5, business card Min. Document Size: 3.5" x 2" (ADF) Paper Weight: 16 lbs. to 34 lbs. Interface: Hi-speed USB 2.0 Power Source: 24Vdc, 2.0A Power Consumption: <38.
