Bluetooth Blood Pressure Monitor (Arm Type) MODEL : BPM65ZB User's Manual Please read this Instruction manual carefully before using your blood pressure monster
Index 1. Important Notice, , 1 2. Infended Use 2 3. Device Description 2 4. Description of LCD Display . . 3 5.BatteryLoading 3 8. How to Apply the Arm Cuff 4 7. Date/ Time Set Procedure Countermeasure 7 9. How the Wireless Connection Works, , . #§ 10.Memory Recall and Deletion , , 41 11.Setting the Alarm Clock 12 12. Cautlens In Cleaning. 14 13.Applied Standards. . a5 14.FCC Statement 18 15.Error Indication 18 16.
Important Notice ‘When using this product, please be sure to follow all the notes listed below. Any action against these notices may cause Injury or affect the accuracy. Note 1: Do not disassemble, repair, or remodel the monitor. Note 2: Do not expose the monitor to extreme temperature, very high humidity, or direct sunlight. Note 3: Avoid dropping and rough handling. Note 4: Press Start/Stop button during measurement may cause the BPM stop operating.
intended Use This arm type Blood Pressure Monitor applies the Oscilloscope method to measure human systolic, diastolic blood pressure and heart rate. All values are shown on the LCD monitor and tha results will be sent automatically to your health monitoring device through wireless connection. This device Is designed only for adults.
Description of LCD Display Q Systolic Pressure (3 Date @ Diastolic Pressure @ Heartbeat Symbol 8 @® Pulse Display @ Alarm Symbol @ Time @ Inflation! Deflation Symbol uA aBB @ ® Average Measurement Symbol ng ® Low Battery Symbol Be [yaw ® @ WHO Indicator gore Lilly) ® Memory Set 18:684 M3 gH AGB @® Memory Symbol o-08 Mensa ® Battery Loading 1. Open the battery cover. 2. Load four 1.5V AA typed alkaline batteries in the compartment and then close the cover.
~ © . Make sure the air plug is securely How to Apply the Arm Cuff Inserted In the main unit. Removes tight-fitting clothing from (fx your upper arm. . Si tin a chair with your fest flat on the floor and rest harmonious a table so that the cuff Is at tha same level as your heart. . Turn the palm of your hand Varicose Velcro upward. Apply the cuff on your upper arm. Secure the cuff around | Metal ‘your arm using the Velcro strip. Note: Make sure the cuff Is wrapped firmly in place.
5. The bottom of the cuff should be approximately 0.8" to 1.2" above your elbow. Make sure tha orange marker Is in your inner arm and "Index" is in the range of " «-OK— Note: Naturally, blood pressure varies from two hands, so that always measure your blood pressure on the same arm, In order to ensure comparability of two readings.
Patel Time Set Procedure 1. After Loading the batteries, this device would enter into Date / Time setting procedure and the Month value will be flashed first. ~ . To adjust the value of Month, please press "M1" button and the value will goes up. Once finished, please press "M2" button to confirm the value and go to the next setting. 3. Follow the spats Instructed above to adjust the value of day, year, hour, minute and unit of temperature (°C / °F) consequently.
How to Measure 1. Crass the Start / Stop button. (1) All display symbols appear for approx. 1 seconds. This Is the Initial LCD test. {2) When the monitor completes the necessary preparations before measurement, the last reading result will be shown on the display for 1 second. (3) Then the monitor basing to measure your blood pressure, and you will se the inflation symbol on the display when Inflating.
2. Record the Measurement Result. (1) After the measurement is completed, your blood pressure and pulse rate will ba displayed on the LCD auto (2) Bros M1 to record the measurement In the first zonal, or pros: M210 recede In the second zone. (3) The device would auto record the measurement in tha first zonal If users do not press any button after measurement. ¥ The stored measurements will remain in the memory even when the battles are removed for battery replacement.
3. Temperature Mods (1) After the measurement Is completed, your blood pressure and pulse will be displayed on the LCD automatically. (2) To tum to temperature mods, please press tha START / STOP button to switch to the temperature mode. (3) This device would automatically switch to temperature mods after two minutes Idling. OFF | B43 F 2 min. idle— shut down the temperature display, please remove all four batteries.
How The Wireless Connection Works At the end of the measurement, your blood pressure will be sent automatically to your health monitoring device. You do not need to do anything. If the health monitoring device Is not working or Is not within range of the blood pressures monitor, the blood pressure will be stored In the blood pressure monitor's memory.
Memory Recall and Deletion 1. Memory Recall {1) Under temperature mode, press "M1" button to recall the readings In the first zone, or press "M2" button to recall the readings in the second zone. Then, the average measurement result will be shown on the LCD first. {2) After the average reading is shown on the display, you can press "M1" or "M2" button to track historical records from no.1 to no.80.
Setting the Alarm Clack Your automatic digital blood pressure monitor features an alarm clock. The alarm can be set to ring at three different times in the day. The alarm is especially helpful if you are required to measure your blood pressure at specific times (for example: 7:00 a.m, 12:00 p.m. and 10:00 Figs. 1-3. To set the alarm clock: 1. Press the Mode Button to enter into the alarm setting mode. 2. Continue to press the Mode Button to select the alarm to adjust. 3.
4. After the hour is confirmed, the minutes will begin to flash, Fig 5. Press the M1 button to change the minutes. Once the correct minutes are displayed, press the M2 button to confirm. 5. The alarm feature must be turned on immediately after setting the time for the alarm. Press the M1 Button to turn the alarm on, Flg. 6. Press the M1 Button a second time to turn the alarm off, Fig. 7. 8. Press M2 Button to confirm the setting then automatically switch to the temperature mode. 7.
Cautions in Cleaning 1. Wipe the monitor with a piece of cloth moistened with water or detergent, then wipe It dry. 3% Please be careful so that water do not get Into the unlit. It may cause damage or gasoline. 2. Do not use benzine, thinner, strong detergent or gasoline. 3. Do not wash or wet the arm cuff.
Applied Standards This product conforms to the provisions of the EC directive MDD (93/42/EEC}.
FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC Statement * FCC Caution: To assure continued compliance, {example — use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. * This device complies with Part 15 of the FCC Rules.
Error Indication If measurement is not made correctly, the following error will be displayed. Error Cause How to Correct Err |1. Pressurs is higher Press START/STOP than 330 mm Hg. button once to turn to 2. Keyparts ara fall. | temperatures mode. Take ares In awhile, measure EE 1-Youmaymove your | again without moving body immortalizing | your arm or body. measurement. 2. The measurement reading Is extremely high or low. Err +2 The batteries are Replace the batteries with almost exhaust. new ones.
Product Specification * Range of Measurement: Blood Pressure: 30 to 280mmHg Pulse: 40-189 beats/ min * Accuracy Calibration: Blood Pressure: 3mmHg Pulse: * Ambient temperature: * Operation Environment: Temperature: 10 to 35°C Humidity: 15% to 95% * Storage/Transportation Environment : Temperature: -20°C to 50°C Humility: non-condensing) * Ambient Temperature: Range: * * Wright: Approximately 380g (excluding batteries) * Memory Set: 2X60 memory with latest 3 readings average * Accessories: M size cuff for ar
