Model 4003 Remote Start Owner’s Guide © 2009 Directed Electronics, Vista, CA G4003L 2009-04
Contents Warning! Safety first..........................................................................................2 What is Included ............................................................................................4 Important Information.........................................................................................4 Your Warranty...........................................................................................4 Using Your System . .........................................
Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage).
After the remote start module has been installed, contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear.
What is Included • • • • The control module A push-button programming switch Your warranty card A shut-down toggle switch Important Information Congratulations on the purchase of your remote start system. This system has been designed to provide years of trouble-free operation. By carefully reading this owner’s guide prior to using your system, you will maximize the use of this system and its features.
Using Your System ➢ Remote Start This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehicle with the climate control system. If interior heating or cooling is desired, the climate controls must be preset, and the fan blower must be set to the desired level prior to remote starting the vehicle.
When you are ready to drive the vehicle: 1. 2. Insert the ignition key and turn it to the ON (not the START) position. Press the brake pedal. The remote start system shutdowns but the motor continues to run because the ignition has been turned on. The vehicle now operates as usual. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
To perform Valet Take-Over: 1. 2. Before turning off the engine, press the auxiliary channel on your Keyless Entry or Security system. (See your authorized Directed Dealer for the programmed number of times required to activate remote start.) Turn the ignition key to the OFF position. (The engine will stay running.) 3. The engine will run until the pre-programmed time elapses or a shut-down input is received. (See page 9 for complete list of shutdown inputs.
Programming options Programming options control your system's normal operational set-up. Most options do not require additional parts, but some may require installation labor. The following is a list of the programmable options, with the factory settings in bold. • 12, 24, or 60 minute run time. Your system can be programmed • to allow the vehicle to run for 12, 24, or 60 minutes when remote started. Can be set up to minute increments by your installer. Parking lights flashing or constant.
Glossary of Terms Control Unit: The “brain” of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all the system functions. Valet Button: A small push-button switch mounted somewhere inside the vehicle. It is used for programming the features of this system. © 2009 Directed Electronics. All rights reserved.
To remote start the vehicle • Press the auxiliary channel the programmed number of times required, (1, 2, or 3) to activate remote start. To shut down remote start • While the vehicle is running, press the auxiliary channel the programmed number of times required, (1, 2, or 3) to shut down remote start. To perform valet take-over • While the vehicle is running, press the auxiliary channel the programmed number of times required, (1, 2, or 3) to activate remote start. Turn the ignition to OFF.
Notes 12 © 2009 Directed Electronics. All rights reserved.
Notes © 2009 Directed Electronics. All rights reserved.
Limited Consumer Warranty For a period of one calendar year from the date of purchase of this auto-security device, Directed Electronics, (Directed) promises to the ORIGINAL PURCHASER to repair or replace (at Directed’s election) with a comparable reconditioned model, any Directed unit (hereafter the “unit”), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories which proves to be defective in workmanship or material under reasonable use, provided the follow
In the event of a claim or a dispute involving Directed or its subsidiary, the venue shall be in San Diego, California. California state laws and applicable federal law shall apply and govern the dispute.
The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology. Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.