MA-909 Instruction Manual ELECTRONICS CO., LTD.
Electronics Co., Ltd. Head office: 814, Pei-Kang Road, Chiayi, 600, Taiwan. Taipei office: 5, Lane 118, Sung-teh Road, Taipei, 110, Taiwan. Web-http: //www.mipro.com.tw E-mail: mipro@mipro.com.
WIRELESS MIXER Operating Manual The traditional design concept of the portable "all-in-one" wireless amplifier consists of a unit with a CD player, cassette player, wireless receiver, and control mixer mounted inside the active speaker cabinet. Although it is easy to use and convenient for low power portable amplifier systems, this design is not suitable for use in high power amplifier systems. It will not only be limited in its function and performance, but it will also be inconvenient to operate.
WIRELESS MIXER Operating Manual 1. PART NAMES AND FUNCTIONS Front Panel: 8 4 (1) 7 5 6 3 2 1 Power Switch & Indicator: When switch is turned on, the indicator illuminates to show normal power status. (2)(6) MRM-70 ACT Receiver Modules: Features auto scan, ACT button, RF & AF meters, squelch control, channel display, & volume control. (3) Control Panel: Controls the volume of all sources & sends output to transmitter.
WIRELESS MIXER Operating Manual Back Panel: 9 10 11 12 13 (9) Antenna: Receiver Antenna. (10) DC Input Jack: Connects unit to 12V DC from the AC/DC adaptor. (11) Power Supply Socket: AC cord socket (12) Transmitter Antenna: Transmits mixed audio to amplified speaker receiver modules. (13) Rackmount Brackets: Allow installation of the receiver into an EIA 19-inch standard rack case.
WIRELESS MIXER Operating Manual A. Receiver Module Part Functions A5 A6 A7 CHANNEL NOISE A8 RF SCAN ACT SENSITIVITY AF VOLUME A4 A3 A2 A1 (A1) Power Switch / Volume Control: Allows you to turn the mixer on & off. The AF LED light will flash when mixer is turned on. Increase the volume by turning in a clockwise direction. (A2) Audio Signal Level Indicator: Indicates the audio levels received from microphones.
WIRELESS MIXER Operating Manual B. SWITCHABLE CHANNEL FUNCTIONS 1. Functions: (a) This system incorporates an advanced PLL-synthesized oscillator design which is preprogrammed with 16 switchable frequencies. The user may freely select any of the preprogrammed frequencies. 2. How To Select a Frequency: (a) Auto Scanning Frequency Setup: Hold down the SCAN button (A5) and release when the channel indicator (A6) starts to flash. It will flash for a total of 6 times.
WIRELESS MIXER Operating Manual C. ACT Button 1. Hold the transmitter to be programmed about 20 cm from the ACT button with the "ACT" marking of the transmitter facing the ACT button. 2. Press the ACT button. The transmitter is programmed when the RF meter shows a full signal. ACT D. Receiver Module Installation 1. Up to 2 receiver modules can be installed. 2. Each receiver module is equipped with "PILOTONE" and "NOISE LOCK" dual-squelch circuitry that eliminates noise interference. 3.
WIRELESS MIXER Operating Manual E、 Control Panel Functions: E7 E1 E2 E3 E4 E5 E6 E8 E9 (E1) Headphone Jack: Stereo headphone jack to monitor the mixer output. (E2) Headphone Volume Control: Separately controls the headphone volume. (E3) Master Volume Control: Controls the overall output volume of mixer. (E4) LINE IN Volume Control: Separately controls the LINE IN (E7) volume. (E5) MIC Volume Control: Separately controls the wired microphone (E9) volume.
WIRELESS MIXER Operating Manual G、How to Setup Wireless Interlinking Transmitter: 1. To change transmitting channel, hold channel button on the front panel for 2 seconds. After numeric LED starts blinking, press channel button again to change preset channel. At this stage, channel will be changed when you press the channel button. 2. When numeric display has changed to one's desired channel, simply release the button and channel setup is completed after numeric LED blinks six times.
WIRELESS MIXER Operating Manual 2. CD Player installation: A. Remove screws holding the blank panel and remove the panel (see Fig. 3-1) B. Insert the CD player into the mixer (see Fig. 3-2) C. Reinstall screws to secure the player (see Fig. 3-3) Fig. 3-1 Fig. 3-2 Fig.
WIRELESS MIXER Operating Manual 3. Operation Notes and Precautions: 1. Microphones have priority over music inputs. When music is playing and a microphone receives an audio signal, the music will be muted. As soon as there is no longer an audio signal to the microphone, the music will fade in. 2. Although the same frequency band may be used, it is important that the frequency of the MT-90 transmitter and the MRM-70 receiver module are not the same. Otherwise, the MA-909 will not operate properly. 3.
HANDHELD WIRELESS MICROPHONE Operating Manual 1. PART NAMES AND FUNCTIONS 1 2 3 4 5 6 7 8 (Fig.1) 1. Grill: Protects cartridge, prevents "POP" noise and prevents microphone from rolling with polygonal shape. 2. Battery Status Indicator: Indicates power on / off and the battery status. When the power switch is turned ON, the red LED indicator flashes briefly, indicating normal battery status.
HANDHELD WIRELESS MICROPHONE Operating Manual 2. BATTERY INSTALLATION (Fig.2) 1. Unscrew the battery cap (6) in a counter-clockwise direction. 2. Insert a 9-volt battery into the battery compartment (5), observing the correct polarity as shown in Fig. 2. The moment the battery touches the terminals, the indicator (2) will flash briefly, indicating correct polarity. However, if no flash occurs, either the polarity is incorrect or the battery is dead.
BODYPACK TRANSMITTER Operating Manual 1. PART NAMES AND FUNCTIONS 1 2 3 4 5 6 7 10 8 9 ACT (Fig. 1) 1. MIC Input Jack: Connects to either a lavaliere or headset microphone. (See Section 3 for connection details) 2. Power Switch: Switch to ON position for operation. Switch to OFF position when not in use. 3. Battery Status Indicator (red): Indicates power on / off and battery status. (a) When power switch is turned on: The LED indicator flashes briefly, indicating normal battery status.
BODYPACK TRANSMITTER Operating Manual 9. Battery Compartment and Cover: Accommodates one 9-Volt battery. 10.Detachable Belt Clip: Allows 360 degree rotation to suit transmitting angles. To detach simply use a screwdriver at a 45 degree angle (see diagram). 2. OPERATING INSTRUCTIONS 1. To adjust GT/MT Switch (8), and Gain Control (7), simply push down both snap locks on the sides of battery cover and flip it backwards to expose the adjustment panel. 2.
BODYPACK TRANSMITTER Operating Manual 3. AF 4-PIN INPUT CONNECTION METHOD (1) 2-Wire Electret Condenser Microphone Capsule PIN 1 SHIELD AUDIO 2 4 1 3 2 3 4 (2) 3-Wire Electret Condenser Microphone Capsule SHIELD PIN 1 2 AUDIO 4 1 3 BIAS 3 2 4 (3) Dynamic Microphone 2 1 SHIELD PIN 1 3 2 AUDIO 4 1 3 2 3 4 (4) Electric Guitar SHIELD PIN 1 2 AUDIO 4 1 3 2 3 4 (5) Line-in (Impedance 8K ATT.
BODYPACK TRANSMITTER Operating Manual 4. BATTERY INSTALLATION 1. Push down both snap-locks on the sides of battery cover to open (Fig. 3). 2. Insert a 9-volt battery into the battery compartment observing the correct polarity as shown in (Fig. 4). Then close the battery compartment as shown in Fig. 4). (Fig.3) (Fig.4) Note: When the microphone is not in use: Make sure the power to the microphone is switched off.