High Definition Terrestrial Receiver DMB-TH8033 User Manual
Table of contents 1 2 3 4 5 6 7 8 9 INTRODUCTION ...........................................................................................................................34 MAIN FUNCATIONS AND FEATURE ...........................................................................................34 THE REMOTE CONTROL .............................................................................................................35 FRONT AND REAR PANEL..........................................................
IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury. 33 This symbol indicates important instructions accompanying the product.
1 INTRODUCTION This user manual is intended to guide you through the operation for the DMB-TH High Definition Digital Terrestrial Receiver. 2 MAIN FUNCATIONS AND FEATURE This product is a high performance and cost-effective HDTV Terrestrial receiver. It fully complies with DMB-TH receiver requirement specifications. It provides users with all digital terrestrial TV and radio signals being broadcast in Standard Definition or High Definition. Functions 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34.
3 THE REMOTE CONTROL Photograph Key Function MUTE Disable Audio output STB POWER Power on/off the STB 0-9 numeral buttons, for input of numbers or for selecting a TV channel This is one learning handset and use to learning the handset of TV SET. Recall last channel while watching digital TV or listening to radio. Press TV/R key to switch between TV program and Radio program. 0…..
Battery Installation Insert the batteries while observing the correct (+) and (-) polarities as illustrated below: About the batteries z z If the remote control unit fails to work even when it is operated near the LCD TV / monitor, please replace the batteries. Use size UM-4 (AAA) batteries. Notes: z z z z z Do not use rechargeable (Ni-Cd) batteries. Do not attempt to recharge, short circuit, disassemble, heat or throw the batteries into the fire.
4 FRONT AND REAR PANEL REAR PANEL 4.1 Rear Panel ANT IN Digital Terrestrial TV Broadcast signal input Loop OUT Output of Digital Terrestrial TV Broadcast signal HDMI Digital HDTV video output with HDCP. HDMI version 1.1 Video Composite video signal output YPbPr High Definition Component video output Coaxial Digital audio output Audio L/R Analog Audio output Optical Digital audio output S-video S-Video output connect to the TV SET DC-12V DC 12V 1.5A Power input 4.
5 INSTALLATION Note: A Digital TV Antenna is used to connect to the Terrestrial Receiver. The Antenna should be used where the user is within an area with Digital Terrestrial TV coverage but the premises in which the user intends to use the Receiver has not yet been upgraded with Digital Terrestrial TV receiving capability. (Please refer to “Installation” for details.
displayed. A list of channels will be displayed on the screen after the searching is successfully completed. You could press the “OK” key on the remote to exit. Channel scanning is completed successfully, a list of channels found during the scanning process is displayed on screen and you could press EXIT key to exit. If no channel is found during the channel searching process, the user may adjust the antenna position to obtain optimal TV signal.
5.1 INFORMATION BAR When pressing the “INFO” key during any TV programs, the information bar will be displayed on the bottom of the screen. The information bar contains the following details: v Channel name and the LCN v Current time and the current/next program of the channel v Signal strength and Quality of the current channel v You also could find some icons such as HD, AC-3, and TTX etc on the left down of the information bar.
5.3 SUBTITLE The programs have multilingual subtitle information. You may press SUBTITLE key to select the preferred subtitle language. The subtitle information window would display on the screen after you press SUBTITLE key. All the subtitle languages would display on the subtitle information window. The screenshot is illustrated below. Press UP/DOWN key to move the cursor and press OK key to select the preferable subtitle language. 5.
5.5 ASPECT RATIO The aspect ratio of the video can be 4:3 (also know as Anamorphic Image) or 16:9 (also know as widescreen TV). Normally the aspect ratio of standard definition video should be 4:3 and the high definition video should be 16:9. In order to have excellent quality on the TV set, users have to set their preferred aspect ratio. Press the ASPECT key to display the aspect ratio setting window. The screenshot of the aspect ratio window is illustrated below.
5.6 TELETEXT Press TELETEXT key to launch the TELETEXT window during any TV channels. The entire TELETEXT with different language will display on the TELETEXT window. Press UP/DOWN key to select preferred language TELETEXT and press OK key to launch TELETEXT. 5.7 TV CHANNEL AND RADIO CHANNEL LIST Press OK key to display the entire TV or radio channel when watching any TV programs. The screenshot is illustrated below. Press TV/R on the remote control to switch the TV channel or radio channel.
5.8 FAVOURITE CHANNEL You can add any channels to your favourite’s channel list and press FAV key on the remote control to launch your favourite’s channel list. Press UP/DOWN key to get the preview of the channel on the right of the screen. Press OK to confirm or press EXIT key to watch the TV.
6 MENU INFORMATION 6.
6.2 MAIN MENU Press MENU key on the remote control to display main menu. The screenshot is shown below. You can find Program List, File Manager, Installation, Program Edit, System Setting and Product Info on the main menu. Choose the option and Press EXIT or OK key to go back the TV program. 6.3 PROGRAM LIST Choose the Program List item highlighted on the main menu. The entire TV channels or radio channels would display on the program list. The screenshot is illustrated below.
Manager directly. File Manager menu allows the user to manages the file that were storage on the extend hard disk which connect to the receiver through USB2.0 interface. 6.4.1 All file Select All File item and the entire file on the extend hard disk will display a list of files on the screen. Delete the highlight file by pressing RED key and then go back to the previous root by pressing BLUE key. 6.4.2 PVR File Move the cursor to the PVR FILE item.
6.5 CHANNEL SEARCH Enter the Main Menu by pressing the MENU key, press the DOWN key and move the cursor to “Install”, press the OK key to confirm. The “Install” allows the user to search the channel. You have to input the pin code before you enter the installation menu. The default value is “0000”. 6.5.1 Manual Search Select Manual search mode while the installation mode item is highlight. Input the preferred frequency by press “0…9” number key on the remote control.
6.5.2 Auto Search Select “Auto” while the Mode item is highlighted. You also could set the antenna power supply for the flat antenna if it is necessary. Press OK key to start auto search after setting the preferred parameters. (Note: When there are channels already in the channel list, running auto search would clear all the channels. A message box would pop up with the following message. Press “OK” to start auto search or “Exit” to quit). 6.
6.6.1 Delete Channel Press RED key to delete the highlighted channel on channel edit menu. An “X” icon would be display on the left of the channel name after you press RED key. You may have to input the password if you want to delete a locked channel. Press EXIT key to exit the channel edit menu and save it. 6.6.2 Lock Channel Press GREEN key on the remote control to lock or unlock the highlighted channel. You have to input the password if you want to lock or unlock the channel. Default value is “0000”.
6.6.4 Move Channel Press BLUE key on the remote control to sort the channels, press OK to confirm. You may have to input the password when you sort the lock channel. Press EXIT key to exit and save.
7 SYSTEM SETTINGS Press MENU key on the remote control and choose the SYSTEM SETTINGS. The sub-menu was including AV Settings, Language Settings, Time Settings, PIN Settings, Network Settings and Factory Def. 7.1 AV SETTINGS The following options are available under the AV Setting sub-menu. Aspect Ratio, Aspect Mode, Video Resolution, Video Type, Audio Track and Digital Audio output. 7.1.1 Aspect Ratio Set the aspect ratio as 4:3 or 16:9 that you prefer.
7.1.2 Aspect Mode Set the aspect mode as Letterbox, Pan Scan or Full screen that you prefer picture on the TV SET. It is corresponding with the stream and the TV SET that connected to the receiver. Press MENU key or EXIT key to go back to the previous menu. Please read the 6.5 ASPECT RATIO to get further more information. 7.1.3 Video Resolution Set the video resolution output as 480P, 576I, 576P, 720P and 1080i that you prefer to get the excellent video quality on the TV SET.
7.1.4 Video Type Set the Video output type as PAL, NTSC or AUTO. AUTO will automatically correspond with the program and the TV SET that connected to the receiver. It is highly recommended. 7.1.5 Audio Track Set the audio track as Stereo, Left, Right or Mono. Stereo is recommended. Please read the 6.2 Audio language and audio mode to get further more information. 7.1.6 Digital Audio Output This allows setting the HDMI, Coaxial and Optical digital audio output by PCM or AAC/AC3 format.
7.2 LANGUAGE SETTINGS Select the Language Settings sub-menu by press OK key on the remote control. This sub-menu allows the user to set the language for the user interface, audio output language, TELETEXT language and subtitle language. Press MENU key or EXIT key go back to the previous menu. 7.2.1 Menu Language Set preferred menu language. Press MENU key or EXIT key go back to the previous menu. 7.2.
7.2.3 Subtitle Language Select Subtitle Language and Preset the preferred subtitle language when a programme is broadcasted with several subtitle languages. If the preset subtitle language could not find in the program, you may select the first subtitle language from the program. Please read the 6.3 Subtitle for more information. 7.2.4 Teletext Language Select Teletext Language item and preset the preferred subtitle language when a programme is broadcasted with several Teletext languages.
7.3 TIME SETTINGS Select Time Settings item and enter to the Time Settings sub-menu by press OK key. The Time Settings sub-menu allows the setting of time preferences. The following options are available in the Time Settings sub-menu, Time mode and Time Zone. Select the item on the Time Settings sub-menu enters to the next sub-menu. The receiver would get the current time from the broadcaster. Select Time Zone and preset the preferred time zone up to the place where the receiver was used.
7.5 FACTORY RESET This function allows user to return the Receiver to factory default settings. From the System setting sub-menu, select Factory reset and enter the system PIN-code. The reset process will start automatically. The default PIN-code is 0000. Please note that after resetting the Receiver, all previously stored TV channels will be lost. The Receiver may take approximately 30 seconds to complete the resetting. 7.6 PRODUCT INFO.
8 UPDATE THE RECEIVER BY USB2.0 INTERFACE 8.1 COPY THE UPDATE FILE TO THE USB DRIVE FROM PC 1. Please go to service website or contact our customer service to get the latest software for updating the Receiver. 2. Plug the USB drive to the PC and backup the entire data of the USB drive. Right click the USB drive and select Format item. Format the USB drive as FAT32 file system. 3. Copy the update file that name as “dh-update.ud” to the root of the USB drive. Then remove the USB drive from the PC.
9 SPECIFICATION Tuner Input Connector IEC 16902. Female Input Frequency Range VHF&UHF Num of RF Inputs 1 Input impedance 75 ohm Input Level -78 dBmV ~ -20 dBmV RF output Connector (bypass)IEC 169-2 Male Loop through 47-862 MHz Demodulation Standard GB20600-2006 DMB-TH Guard interval Modes 420/595/945 Active Symbol duration FEC Modes Rate 0.4/0.6/0.
Subtitles & Teletext Subtitle DVB Subtitle Teletext EBU TELETEXT Rear Panel CVBS outputs 1 CVBS video output Audio CINCH 2 Analog Audio L/R connectors (white/red color) Y/C S-Video Optical S/PDIF Digital Audio output Coaxial S/PDIF Digital Audio output YPbPr outputs Analog HDTV video output HDMI Digital HDTV video output with HDCP. HDMI version 1.1 or later USB USB2.
