USER MANUAL Ultra Slim 4K HDMI via HDBaseT 70 Meter Extender with Bi-Directional Power and ARC support AC-EX70-UHD-ARC 1
Table of Contents I N T R O D U C T I O N � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3 F E A T U R E S � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3 IN THE BOX ���������������������������������������������������������
Introduction The AC-EX70-UHD-ARC consists of a transmitter and receiver that connect via single CAT-6a/7 UTP/STP. Connecting an HDMI signal to the transmitter allows for sending HDMI signals up to 70 meters at 1080p and up to 40 meters at 4K60 4:2:0, 4K30 4:4:4. This AVPro Edge audio video extender is the most cost-effective, state of the art, and reliable single CAT 70-meter extender on the market today.
Specifications 4
Troubleshooting Lights - Transmitter/Receiver POWER - On the front (Red). · Light is ON = Power supply is connected and functioning. · Light is OFF = Power supply is not connected or there is no power present. Verify connections, power supply, USP, Outlet, etc... HDBT ACT - On the front (Blue). · Light is on (Flashing) = Normal operation. · Light is off = The HDBaseT Chip is not active (verify power). HDBT LINK - On the front (Blue).
Troubleshooting Lights (HDBaseT Port) STATUS - On the HDBaseT port, back of the Transmitter/Receiver (Amber). · Light is ON (Flashing) = Normal operation · Light is OFF = There is no HDBaseT activity. LINK - On the HDBaseT port, back of the Transmitter/Receiver (Green). · Light is on (solid) = Normal operation. · Light is off = There is no communication between the Transmitter and Receiver. Transmitter Ports POWER 48V - 2 Pin terminal connector. You can power at either the Transmitter or the Reciever.
Receiver Ports POWER 48V - 2 Pin terminal connector. You can power at either the Transmitter or the Reciever. Power will be provided automatically over the Category cable to the other HDBaseT unit. IR OUT/I-PASS/IR IN - There are 3 options for IR (examples are under the section “IR CONFIGURATION” Page 8/9 ). 1. IR OUT: For use with an IR EMITTER (3.5mm). · I-PASS: For use with a MONO 3.5mm cable directly connected to a control system to send IR Signals to the remote end.
IR Configuration There are three different 3.5mm IR ports located on the Transmitter and Receiver. IR OUT - This port is designed to accept an IR Emitter In the example below an IR recieving eye is plugged into the “IR IN” port of the HDBaseT Transmitter, and a IR Emitter is plugged into the “IR OUT” port of the HDBaseT Receiver. This allows you to use an IR Remote control to send and IR signal from the source side (TX) down the category cable to the sync (RX) and control the display.
In the example below a control system is plugged into the “IPASS” port of the HDBaseT Transmitter with a 3.5mm mono cable, and a IR Emitter is plugged into the “IR OUT” port of the HDBaseT Receiver. This allows you to send an IR signal from a control system down the category cable to the sync (RX) and control the display. IPASS - This port is designed to be directly connected to a control system via a 3.5mm Mono cable NOTE: IPASS is only an INPUT. So you can go IPASS in from a control system to IR OUT.
Audio The 3.5mm Extracted Audio port on the Transmitter and Receiver is a dual purpose port. It is designed to accept a 3.5mm stereo cable, or a Mini Toslink (x2 adapters included in kit). · 3.5mm Stero Cable (not included) · Mini TOSLINK (x2 adapters included, Toslink cable not included) Example of Mini-Toslink adapter (2x included in kit) (3.5mm Audio Cable and TOSLINK Cable not included.
EDID Management - Transmitter Default out of the box all the dip switches are down (off) “BYPASS (HDBT)”mode. This will pass the EDID of the connected display to the source un-altered. NOTE: This is a 10.2Gbps extender, when in “BYPASS (HDBT)”make sure the souce is not sending a signal that exceeds this HDBaseT Extender set. See bandwith chart located on page 13 for more information. EDID Copy Instructions Set the DIP switches to 1 1 1 1 (all Up/On) with the connected sink (display) powered on.
RS-232 Configuration For extending RS-232 communication over the Category cable. For these to pass a signal, both the Transmitter and Receiver need to have the Dip Switch set to Normal Mode, not RS-232 Program. Default out of the box is MODE NORM (Normal Mode). RS232 PROG (Program mode for Firmware updating).
Troubleshooting · Verify Power - Check that the power supply is properly connected and on an active circuit. · Verify Connections - Check that all cables are properly connected. · TX/RX Indicator Troubleshooting Lights - Pg. 5-6 · IR Issues - Verify correct connections - P. 8-9 Note: Visibly flashing Emitters may not function properly, if you are experiencing issue try the IR Cables that come in the box. · Lights indicate everything is good but still not getting a picture, this may be a bandwith limitation.
Maintenance To ensure reliable operation of this product as well as protecting the safety of any person using or handling this device while powered, please observe the following instructions. · Use the power supplies provided. If an alternate supply is required, check voltage, polarity and that it has sufficient power to supply the device it is connected to. · Do not operate these products outside the specified temperature and humidity range given in the above specifications.
Support Should you experience any problems while using this product, first, refer to the Troubleshooting section of this manual before contacting Technical Support. When calling, the following information should be provided: · Product name and model number · Product serial number · Details of the issue and any conditions under which the issue is occurring · Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.
Thank you for choosing AVProEdge! Please contact us with any questions, we are happily at your service! AVProEdge 2222 E 52nd St N ~ Sioux Falls, SD 57104 1-877-886-5112 ~ 605-274-6055 support@avproedge.
