THE FLY RBP WIDE SCAN 3D LASER Order ref: 152.763UK User Manual IMPORTANT SAFETY NOTICE Please Read this manual before operating VERSION 1.
Caution: Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty Introduction Thank you for choosing THE FLY laser as part of your effects lighting equipment. This product has been designed to project unique 3D geometric patterns in 3 colours across a wide area. Please read and retain this manual in order to achieve the best results from your purchase and avoid damage through misuse.
CAUTION Please read this manual fully before installing or operating this product as it contains important safety information relating to its installation and operation. This Class 3B laser product emits hazardous levels of optical radiation and will cause injury to the eyes if viewed directly. This product is not suitable for projection directly at audiences or other personnel. This product must not be used for any form of audience scanning application and is for professional use only.
Installation instructions This product must be securely mounted with adequate fixings to hold the weight. If mounted at height, use a safety wire attached to the eyebolt and a secondary fixing point. Position the aperture so that its emission is always directed away from people and objects that are able to reflect the emission towards people. In this regard the separation distances of 3 metres vertically and 2.5 metres horizontally, cited in HS(G)95 and shown below must be observed.
Vertical cross sectional view Unpacking Please check the contents to ensure that the product has been received in good condition. Laser x 1unit IEC Power Lead x 1pc I.R. remote control x 1pc Safety Keys x 2pcs If you find any accessory is missing or the product has arrived with any problems, please contact your retailer at once. This product contains no user-serviceable parts so make no attempt to try to fix or modify this item yourself as this will invalidate the warranty.
Setting up 1. Unpack the laser ensuring all packaging and tape is removed. 2. Always test the laser before fixing in a permanent location. 3. Connect the IEC mains plug and switch the rear power switch on. 4. Insert the safety key and turn to a quarter turn clockwise. At this point ensure that no one is exposed to laser radiation. 5. Select which mode you want to operate the laser in. 6. Leave the laser to run for 10 minutes before installing in its location.
Connecting to mains, earth wire (ground) must be connected. Use the supplied IEC lead to connect to the main power supply as follows: Wire Connection International symbol Brown Live L Blue Neutral N Yellow /Cyan Earth For your safety, please kindly pay attention to all of the warnings below: Always plug in the power plug last and disconnect from the mains when the device is not in use or before cleaning.
Replacing the fuse First disconnect from the mains power supply then remove the fuse holder above the IEC Socket to reveal the fuse. Replace with the correct fuse rating as stated on the product or in the user manual. Then lock the fuse holder cover back into place. General maintenance Be sure to power off the fixture before conducting maintenance. To maintain optimum performance and minimise wear, fixtures should be cleaned frequently.
Front panel 1. 2. 3. 4. Laser aperture Power LED I.R. remote receiver Music LED 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Control panel options Display Mode Press ENTER for setting (press FUNC to exit) Auto modes Sound activated modes Slave mode Remote mode (RBP), (blue), (red), (purple) (RBP), (blue), (red), (purple) (minimum) to (maximum) to = direct slave mode (mimics master unit) = 0.2s delay… = 1.
Microphone sensitivity In sound-activated mode, the sensitivity of the internal microphone can be adjusted via the control panel.
Remote control mode THE FLY laser can be operated using the supplied handheld infra-red remote control. To use this remote control, firstly, remove the plastic tab at the bottom of the remote to activate the internal battery. If necessary, this can be replaced with a standard CR2025 button cell. The Remote mode for the laser unit is set via the control panel as follows… Press the FUNC button until is displayed and press ENTER Direct the handheld remote control toward the I.
DMX mode The fixture is equipped with 3-pin XLR connectors for DMX input and output. These connectors are wired in parallel. Only use a shielded twisted-pair cable designed for 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another. Building a serial DMX-chain: Caution: At the last fixture, the DMX-cable has to end with a terminator.
DMX parameters Channel Parameter CH1 Mode CH2 Pattern CH3 Colour CH4 Colour speed CH5 Zoom CH6 X-axis CH7 Y-axis CH8 Y-axis roll CH9 X-axis roll CH10 Z-axis Value 000-027 028-055 056-083 084-111 112-139 140-167 168-195 196-223 224-251 252-255 000-255 000-049 050-074 075-099 100-124 125-149 150-174 175-199 200-224 225-255 000-255 000-127 128-169 170-209 210-255 000-127 128-191 128-255 000-127 128-191 128-255 000-127 128-191 192-255 000-127 128-191 192-255 000-127 128-191 128-255 Functi
Patterns Value Pattern Value Pattern Value Pattern Value 000-007 064-071 128-135 192-199 008-015 072-079 136-143 200-207 016-023 080-087 144-151 208-215 024-031 088-095 152-159 216-223 032-039 096-103 160-167 224-131 040-047 104-111 168-175 232-239 048-055 112-119 176-183 240-247 056-063 120-127 184-191 248-255 Pattern 152.
Specifications Power supply Power consumption Fuse rating Red laser power Blue laser power Laser class Operating temperature range DMX connection DMX channels Remote control battery Dimensions Weight Laser & LED safety standard 100-240Vac, 50/60Hz (IEC) 15W T1A 250V (20mm glass) 100mW 650nm 120mW 450nm 3B 10 - 40°C 3-pin XLR 10 CR2025 button cell 180 x 155 x 220mm 1.
