TFT-LCD TV W102T USER MANUAL READ CAREFULLY BEFORE OPERATION W102T
IMPORTANT SAFETY INSTRUCTIONS TO PREVENT ELECTRICAL SHOCK. CAUTION DO NOT REMOVE THIS COVER. NO RISK OF ELECTRIC SHOCK. DO NOT OPEN. REFER SERVICING TO QUALIFIED USER- SERVICEABLE PARTS INSIDE. SERVICE PERSONNEL. This symbol indicates dangerous voltage inside the product that presents a risk of electric shock or personal injury. This symbol indicates important instructions accompanying the product. Please read this manual carefully before using this product.
IMPORTANT SAFETY INSTRUCTIONS Do not clean the front with keton-type materials (e.g.Acetone ),ethyl alcohol, toluene, ethy lacid, methyl, or chloride-these may damage the panel. Locate your DC adapter near an easily accessible AC outlet. If your LCD TV does not operate normally in particular, if there are any unusual sounds or smells coming from it unplug it immediately and contact an authorized dealer or service center. High temperature can cause problems.
CONTENT PANEL BUTTON FUNCTIONS Panel control 1 EXTERNAL EQUIPMENT Connecting diagram 2 REMOTE CONTROL HANDSET Remote buttons 3 Battery installation 4 LET'S START Change source operation 5 TV MENU SETUP Picture Channel edit 6 8 TV setting 7 System 9 AV SETUP AV setup 10 DVB FUNCTION SETUP General setup DVB-T setup 11 12 Video setup Password setup 11 14 15 System 16 FM OPERATION FM TROUBLE SHOOTING TV troubleshooting 17 SPECIFICATIONS Specifications 18 DISPLAY MODE Display mode
PANEL BUTTON FUNCTIONS PANEL CONTROL Front panel 1 Indicator( Indicator is red when in standby mode, green when working normally.
2 TV/
REMOTE CONTROL HANDSET BATTERY INSTALLATION When installing battery , please match the two polarities of the battery with the two polarities inside the battery case (positive upward, negative downward), as in the following figure: CR2025 CR2025 2 1 Step 2: Pull the battery holder out. Step 1: Push the button toward left. Step3: Insert one 3VOL LITHIUM BATTERY matching the -/+ polarities of the battery to the -/+ marks inside the battery compartment, as in the diagram.
LET'S START After the unit has been suitably placed / fixed, on the desk or in your car, and all cords are connected for power, input and output . If your unit is not fixed with the battery pack, connect the adapter to the LCD TV, the unit will go into standby mode, and you can see the indicator turn red. If your unit is fixed with the battery pack, and the quantity of electricity is high enough, the unit will go to standby mode, the indicator will turn red.
TV MENU SETUP This product can store up to 100-channel programs (0 99). You can scan and store all the channels through manual or automatic mode. In TV mode, press [SETUP] button on the remote control or top panel and menu will show as follows: Through pressing [ ] button on the remote control, you can select main menu sections(main menu PICTURE sections consist of " PICTURE " , " TV SETTING " , " SYSTEM ") . Press [ PICTURE MODE ] or [OK] button to enter this menu section.
TV MENU SETUP TV SETTING Select " "and menu will show as follows: TV SETTING CHANNEL 2 COLOR SYSTEM AUTO SOUND SYSTEM I FINE TUNE 136.20MHZ MANUAL SEARCH AUTO SEARCH CHANNEL EDIT SELECT Press [ ENTER OK ] button to select item and press [ Item RETURN SETUP ] button to adjust . Description CHANNEL To change the channel number. COLOR SYSTEM Can be changed between: "Auto", "PAL" and "SECAM". SOUND SYSTEM Can be changed between:"BG", "DK", "I" and "L" .
TV MENU SETUP during the searching, you can press [SETUP] button to stop. CHANNEL EDIT TV SETTING CHANNEL 2 SKIP OFF SWAP SELECT Item 38 ADJUST RETURN SETUP Description CHANNEL To select current channel . SKIP To select "ON" or "OFF ", you can select " ON " to make current channel unaccessible while using [CH+/-] button to browse channels. SWAP Press [ ] button to select the channel, and press [OK] button to swap the channel.
TV MENU SETUP SYSTEM You can setup some system configuration here. Press [ ] to select " " item and press [ ] button to enter the following section: SYSTEM LANGUAGE ENGLISH TRANSPARENCY LEVEL 2 SLEEP 0 RATIO 16 : 9 RESET SELECT Press [ ENTER OK ] button to select item and press [ Item RETURN SETUP ] button to adjust or activate. Description LANGUAGE Select OSD language. TRANSPARENCY To change transparency of OSD.
AV SETUP If no signal input in TV or AV mode, the screen will show a similar signal to the following figure. This unit will go into standby mode automatically if there is no signal input for more than 5 minutes.
DVB FUNCTION SETUP DVB-T SETUP DVB DVB- T Setup Page Area Time Zone Parental Age Antenna power Channel setup UK Dis Dis Go To DVB - T Setup Page The DVB-T Setup Page is composed of four parts: Area, Time Zone, parental Age, Channel Setup. Note : Press [ ]button to select different item , and press [OK] or [ ] button to enter it. Press [ ] button to return to the previous menu or to exit the current menu . Cursor button 1. Area You can choose the area of your country.
DVB FUNCTION SETUP Auto Scan Connect the antenna to the RF socket on the TV, if the antenna needs a power supply, please press[ANT.ON/OFF] button to turn on the power for the antenna. Then you can automatically search channels without entering any other information. In the scan process, the scan result will be displayed in the Auto Scan window. Auto Scan Status Freq: 65000KHz TV Total: 00 Radio Total: 00 Found Channels Progress: 40% Press [SEARCH] on remote control more than 3 seconds to auto scan.
DVB FUNCTION SETUP 3.Select channel using [ ] button, press number button [3] to set this channel as a protected one, to prevent children from watching the undesired program. Note: If you set a channel protected, a password will need to be inputted in the Protect Channel window. The default password is 000000. Channel remap You can change every channel position as you like in channel remap window. Reserve channel If you want to watch a special program on a channel at a later time, you can reserve it.
FM OPERATION FM With radio decoder built in , you can enjoy radio programs using this unit. Connect the FM antenna in the accessories to the FM socket on the left panel of the TV, change source to FM. Press [SETUP] button and a menu will show as follows: FM 12 CHANNEL 101.20MHz FREQUENCY MANUAL SEARCH AUTO SEARCH SELECT ENTER OK RETURN SETUP 1. CHANNEL: Display current channel number, press [ ] button to change channel. 2.
FM OPERATION SYSTEM In FM setup menu, select " ", a FM system menu will be displayed as follows: SYSTEM ENGLISH LANGUAGE LEVEL 3 TRANSPARENCY SLEEP OFF RATIO 16 : 9 RESET SELECT ENTER OK RETURN SETUP 1. LANGUAGE Set FM setup menu language. For English, only English. 2. TRANSPARENCY Set the transparency level of FM setup menu, optional settings : OFF--LEVEL 6. 3.SLEEP Set the time of how long before the TV goes into standby mode automatically.
TROUBLESHOOTING Please check for causes of problems in accordance with the following chart before contacting any maintenance personnel. TV TROUBLESHOOTING Symptom Cannot power on Causes and Correction Please make sure the power cord is correctly connected. Please make sure the audio cord is correctly connected.
FM antenna RF Battery pack FM Lithium rechargeable battery 5000mAH, 7.4V Input connector Frequency range (VHF/UHF) IEC-Type, IEC 169-2, Female Channel range(VHF/UHF) 7 & 8 Mhz FM frequency range 87.
DISPLAY MODE SUPPORTED VIDEO INPUT MODE Format Hor scanning frequency Ver scanning frequency Vert scan type 720X480 31.47 59.94 480P 720X480 15.734 59.94 480i 720X576 31.25 50 576P 720X576 15.625 50 576i NOTE Specifications and design are subject to change without notice.
