User's Manual

GETTING STARTED
Put 2 batteries into each of your transmitters.
The handheld takes 2 AA batteries and the
battery compartment can be located by
unscrewing the bottom of the handle. The belt-
pack takes 2 AA batteries and the compart-
ment can be located by swinging open the
door. See diagrams on pages 10 and 11.
Attach the two antennae to the back of your
receiver. Attach by screwing onto the receiver
in the proper location. See picture of your
receiver on pages 6, 8 or 9 for help with locat-
ing the proper location.
Connect your sound system to your wireless
microphone system using either 1/4" or XLR
cables but not both at the same time. You will
need to attach 1 XLR cable for each transmit-
ter that you will be operating.
For all receivers, when opting to use a 1/4"
cable (instead of XLR cables) then only one
1/4" cable needs to be used per receiver
regardless of how many transmitters you are
operating with that receiver.
Generally a cleaner more clear sound can be
attained by using XLR cables. We highly rec-
ommend the use of XLR cables instead of a
1/4" cable with your system.
Plug the wall wart power supply into the back
of your receiver and then into an electrical out-
let.
Power on your receiver using the power
switch.
Power on your transmitter.
Handheld: Use the power button to power on
the device.
Beltpack: Power on using the button located
on the central panel of the beltpack. Push
power button for 3 seconds. See diagram on
page 11.
Now you must sync your transmitter and
receiver to the same frequency or channel. By
using the receiver controller on your receiver
you can toggle through the various receiver
settings and choose the IR sync mode. The
receivers allow you to access IR sync mode by
simply hitting the button on your receiver that
says "IR SYNC".
If you are going to be using more than one
transmitter at a time then each transmitter
must be set to a different frequency or chan-
nel. You can use the receiver controller to
select different frequencies (or channels) for
additional transmitters. Choose a frequency or
channel for a specific receiver channel and
sync the next transmitter to a different fre-
quency or channel than the previous trans-
mitter(s). Refer to the page in this manual
that gives instructions for your specific
receiver for detailed instructions.
Locate the IR sync window on the receiver.
Look for the letters IR on your receiver to
locate the window. Please see pictures on
pages 6, 8 and 9 to help locate the IR sync
window location.
Handheld Transmitter:
Point the small IR window on the front of
your transmitter facing towards the IR sync
window on the receiver at a distance of
about one half inch or less. Hold the
handheld in this position. When properly
aligned the handheld should automatically
change frequency to match the frequency
of the receiver. See page 10.
Beltpack Transmitter:
Open the compartment where the batteries
are stored. Align the red IR sync window on
your beltpack to that on your receiver to
automatically sync the transmitter to the
frequency of the receiver. See page 11.
Frequency display can be found on page
10 for the handheld and page 11 for the
beltpack.
Make sure the volume knobs on your
receiver are turned up to the desired level.
Your wireless microphone system should
now be operational as long as all your
sound equipment is set up properly as well.
When you are finished make sure to power
off your transmitter and receiver.
Step 1:
4 5
Step 8:
Step 2:
Step 3:
Note:
Step 4:
Step 5:
Step 6:
Step 7:
Note:
Note:
Step 9:
Step 10:
For detailed instructions regarding
using the IR sync function of your
receiver please refer to the IR sync
instructions that follow for the specific
system that you purchased.
EMPEZANDO
Coloque 2 baterias en cada uno de sus trans-
misores. El dispositivo de mane lleva 2 bater-
fas AA y el compartimiento de la bateria
puede ser localizado desenroscando la parte
inferior del mango. La caja de la cintura lleva
2 pilas AA y el compartimiento se puede lo-
calizar al abrirse la puerta. Vea los diagramas
de las páginas 10 y 11.
Conecte las dos antenas en la parte posterior
de su recibidor. Sujete atornillando en el reci-
bidor en el lugar adecuado. Vea la imagen de
su receptor en las páginas 6, 8 y 9 para ayu-
dar a localizar el lugar adecuado.
Conecte su sistema de sonido a su sistema
de micrófonos inalámbricos utilizando ya sea
cables de 1/4" o XLR, pero no ambos al
mismo tiempo. Usted tendrá que conectar 1
cable XLR para cada transmisor que va a
operar. Para todos los recibidores sólo un
cable de 1/4" debe ser utilizado independien-
temente del número de transmisores que se
estan operando, siempre y cuando no se
exceda el número de transmisores que su
sistema puede funcionar a la vez.
Generalmente se obtiene un sonido mas claro
y limpio con el uso de cables XLR. Recomen-
damos bastante el uso de cables XLR en
lugar de cables de 1/4" con su sistema.
Conecte la fuente de corriente de AC en la
parte posterior de su receptor y luego a una
toma eléctrica.
Encienda el recibidor con el interrupter de
encendido. Presione el botón de encendido
durante 3 segundos.
Encienda su transmisor.
De Mano: Con el interrupter deslizante de dos
posiciones deslizándolo hasta llegar a la
posición de encendido.
De Cintura: Encienda con el botón situado en
la parte superior de el aparato. Pulse el botón
de encendido durante 3 segundos. Vea el
diagrama en la página 11.
El aparato de mano dispone de un interrupter
de tres posiciones que le permite silenciar el
transmisor sin apagarlo, deslice el interrupter
a la posición a mitad de camino entre el en-
cendido / apagado posiciones.
Ahora hay que sincronizar el transmisor y el
recibidor a la misma frecuencia o canal. Al
utilizar el controlador receptor en su recibidor
puede cambiar entre las distintos ajustes del
recibidor y elegir el modo de sincronización
IR. El recibidor puede permitirle acceder a
modo de sincronización IR simplemente pul-
sando el botón en el recibidor que dice "IR
SYNC".
Si va a utilizar más de un transmisor a la vez
entonces cada transmisor debe ajustarse a
una frecuencia o canal. Usted puede utilizar
el controlador del recibidor para seleccionar
diferentes frecuencias (o canales) para trans-
misores adicionales. Elija una frecuencia o
canal para un canal receptor específico y
sincronizar el siguiente transmisor a una
frecuencia o canal del transmisor anterior.
Consulte la página de este manual que con-
tiene instrucciones para su receptor especifi-
co para obtener instrucciones detalladas.
Localice la ventanilla de sincronización IR en
el receptor. Busque las letras IR en su recibi-
dor para localizar la ventanilla. Par favor vea
las imágenes en las páginas 6, 8 y 9 para
ayudarle a localizar la ubicación de la venta-
nilla de sincronización IR.
Transmisor de Mano:
Apunte la parte posterior del transmisor con
la pequeña ventanilla en la parte posterior
del transmisor mirando hacia el recibidor
dentro de aproximadamente media pulgada
de la ventana de sincronización IR en el
recibidor. Sostenga el aparato de mane en
esta posición. Cuando está correctamente
alineado el dispositivo debería cambiar au-
tomáticamente la frecuencia para que coinci-
da con la frecuencia del recibidor. Vea la
página 10.
Transmisor de Cintura:
Abra el compartimiento donde se almacenan
las baterías. Alinie la ventanilla de sincroni-
zación IR de su aparato de cintura a de su
recibidor para sincronizar automáticamente
el transmisor a la frecuencia del recibidor.
Vea la página 11.
Visualización de la frecuencia se puede
encon trar en la página 10 para el aparato de
mano y en la página 11 para el aparato de
cintura.
Asegúrese de que las perillas de volumen del
recibidor se suban hasta el nivel deseado.
Su sistema de micrófono inalámbrico ahora
debería estar en funcionamiento, siempre y
cuando todo el equipo de sonido está config-
urado correctamente también. Cuando haya
terminado, asegúrese de apagar el transmi-
sor y el recibidor.
Paso 1:
Para obtener instrucciones detalladas
sabre el uso de la función de sincroni-
zación IR de su receptor, consulte las
instrucciones de sincronización IR que
siguen para el sistema especifico que
ha adquirido.
Note:
Paso 2:
Paso 3:
Note:
Paso 4:
Paso 5:
Paso 6:
Note:
Paso 7:
Paso 8:
Note:
Paso 9:
Paso 10: