Quick Start Guide

Network Video Recorder
Quick Start Guide
1. Notes
● Please read this instruction carefully for correct use of the product and
preserve it for reference purposes.
● All the examples and pictures used here are for reference only.
● There may be several technically incorrect places or printing errors in
this manual. The updates will be added into the new version of this manual.
The contents of this manual are subject to change without notice.
● This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.
2. HDD Installation
The interfaces of the rear panel are for reference only.
3. Rear Panel Instruction
4. Startup & Shutdown
6. Network Configuration
The default username is admin and the default password is 123456. You must
configure the wizard if you start the NVR for the first time and you may change
the password when you configure the wizard for the first time. You can skip
the settings of wizard next time. Click “Start” and select “Login”. This will
take you to see a login box. Input default username and password you set and
you can see the live image.
►Startup
① Connect the monitor and the power.
② The device will boot and the power indicator will display blue.
③ A wizard window will pop up.
►Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This will bring up a
shutdown window. The device will shut down by clicking “OK” button.
Then disconnect the power.
5. Login
After you finish adding IP cameras, you can see the live images through the
monitor of the NVR. The following will mainly introduce how to add the IP
cameras via LAN/WAN. This NVR has two network ports, you can select the
►LAN
① Set the network of the NVR. Go to Start → Settings → Network →TCP/IP.
Input IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP
in both the NVR and the router.
② Go to Start → Settings → Network → Port. Input HTTP port (the default
value is 80), server port (the default port is 6036).
③ User may modify the MTU (maximum transmission unit) value according to
the real network situation. Click “Apply” to save the settings.
④ Go to Start → Settings → Camera → Add Camera. The NVR will automatically
refresh the cameras searched. The IPC which supports the Onvif protocol may
be added manually. If the IPC searched is not in the same local network as the
NVR, you should select the device and click to modify the IP address.
4.0.0.1.beta 1
Version
1
2
192.168.1.20
192.168.1.38
XXX80
80
80
XXX
XXX
XXX
3.4.2
3.4.2
255.255 .255.0
255.255 .255.0
No.
Address
EditPort
Protocol Model
Subnet Mask
3
192.168.2.45
XXXXXX
255.255 .255.0
Quickly Add
Manually Add
Add Camera
Selected: 1/3
Add
Default Passwo rd
Remain Bandwidth: 108 / 120 Mb
Cancel
Mac Addres s
Address
Port
CE :98 :23 :75 :35 :22
Edit Camera
80
192 .168 . 1 . 45
255 . 255 . 255 . 0
admin
192 .168 . 1 . 1
Subnet Ma sk
Usernam e
Gateway
Passwor d
OK Cancel
Username
Password
admin
Login
Enter Password
Display Password Log In Automatically
LoginEdit Security Question Cancel
This series of the product supports 16 SATA hard drives. Please make sure that
the device is powered off before the installation.
① Get the brackets and screws of installing HDDs from the accessories and then
fix two brackets to the HDD.
② Open the front panel of the device.
TCP/IP Port PPPoE DDNS E-mail UPnP NAT Telnet
MAC Address
MAC Address
Ether net P ort 1
Netwo rk Fa ult Tolera nce
00：18：AE：35：64：1A
00：18：AE：35：64：1B
IP Address Settings
Obtai n an IP v4 addres s aut omatica lly Obtai n an IP v6 addres s aut omatica lly
Ethernet Port 1 ( Online )
Ether net Port 2 ( Online )
Addre ss Addre ss
192 . 168 . 1 . 2
0 . 0 . 0 . 0 0
192 . 168 . 1 . 1
Subne t Mas k Mask Le ngt h
Gatew ay Gatew ay
Prima ry Ca rd
MTU
Work P attern (Modi fyi ng work pat ter n need to reb oot )
network work pattern as required. Network fault tolerance and multiple address
setting are optional.
Network Fault Tolerance: Bound two network ports to one IP address. This
pattern can increase the network bandwidth and form a network redundant array to
share the load. When one port goes wrong, the other port will take over the entire
load immediately and seamlessly.
Multiple Address Setting: You shall set the IP address, subnet mask, gateway
and DNS of each ethernet port respectively.
The pictures are only for reference, please refer to User Manual for details.
③ Use one hand to hold the handles of the two brackets respectively and push the HDD into
the HDD slot. Clamp the HDD to make sure the HDD to install successfully.
④ Choose the number of installing HDDs according to your need as above-mentioned methods.
Tips：Hold the handles of the two brackets to pull out the HDD.
screws
bracket
bracket
handles
N
O3
e-SATA
LAN 1
LAN 2
USB
AUDIO IN
AUDIO OUTALARM INALARM OUT
VGA
2 1