Quick Start Guide

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.
All the examples and pictures used here are for reference only. There may be several technically incorrect places
or printing errors in this manual. The updates will be added into the new version of this manual. The contents of
this manual are subject to change without notice.This device should be operated only from the type of power
source indicatedon the marking label. The voltage of the power must be verified before using the same.
Network Video Recorder
Quick Start Guide
This series of the product supports 16 SATA hard drives. Please make
sure that the device is powered off before the installation.
3. Use one hand to hold the handles of the two brckets respectively,
and push the HDD into the HDD slot. Clamp the HDD to make sure the HDD
to install successfully.
4. Choose the number of installing HDDs according to your need as
above-mentioned methods.
Tips: Hold the handles of the two brackets to pull out the HDD
Please check the device and the accessories after getting the device.
If there are any damages, shortages or defects, please contact your
dealer immediately.
For our HN500 series NVRs, the default username is admin and the
default password is 123456. You must configure the wizard if you
start the NVR for the first time and you may change the password
when you configure the wizard for the first time. You can skip the
settings of wizard next time. Click “Start” and select “Login”. This will
take you to see a login box. Input default username and password
you set and you can see the live image.
2. HDD Installation
1. Packing Check
3. Rear Panel Installation
The interfaces of the rear panel are for reference only.
• Startup
1. Connect the monitor and the power.
2. The device will boot and the power indicator will display blue.
3. A wizard window will pop up.
• Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This will bring
up a shutdown window. The device will shut down by clicking “OK”
button. Then disconnect the power.
4. Startup & Shutdown
4. Login
Username
Password
admin
Login
Enter Password
Display Password Log In Automatically
LoginEdit Security Question Cancel
After you finish adding IP cameras, you can see the live images through
the monitor of the NVR. The following will mainly introduce how to add
the IP cameras via LAN/WAN. This NVR has two network ports, you can
select the network work pattern as required. Network fault toleratnce
and multiple address setting are optional.
Network Fault Tolerance: Bound two network ports to one IP address.
This pattern can increase the network bandwidth and form a network
redundant array to share the load. When one port goes wrong, the
other port will take over the entire load immediately and seamlessly.
Multiple Address Setting: You shall set the IP address, subnet mask,
gateway and DNS of each ethernet port respectively.The pictures are
only for reference, please refer to User Manual for details.
5. Network Configuration
• LAN
1. Set the network of the NVR. Go to Start → Settings →
Network → TCP/IP. Input IP address, subnet mask, gateway,
etc. If using DHCP, please enable DHCP in both the NVR and
the router.
2. Go to Start → Settings → Network → Port. Input HTTP port
(the default value is 80), server port (the default port is 6036).
3. User may modify the MTU(Maximum Transmission Unit) value
according to the real network situation. Click “Apply” to
save the settings.
4. Go to Start → Settings → Camera → Add Camera. The NVR
will automatically refresh the cameras searched. The IPC which
supports the Onvif protocol may be added manually. If the IPC
searched is not in the same local network as the NVR, you
should select the device and click to modify the IP address.
1.Get the brackets and screws of installing HDDs from the accessories and then
fix two brackets to the HDD.
2.Open the front panel of the device.
N
O3
e- SATA
LA N 1
LA N 2
US B
AU DI O IN
AU DI O OUTAL AR M INAL AR M OUT
VG A
2 1
TCP/IP Port PPPoE DDNS E-mail UPnP NAT Telnet
MAC Address
MAC Address
Ethernet Port 1
Network Faul t Tolerance
00：18：AE：35：64：1A
00：18：AE：35：64：1B
IP Addr ess Settings
Obtain an IPv4 a dd re ss a ut om at ic al ly Obtain an IPv6 a dd re ss a ut om at ic al ly
Ethern et Por t 1 ( On line )
Ethern et Por t 2 ( On line )
Address Address
192 . 168 . 1 . 2
0 . 0 . 0 . 0 0
192 . 168 . 1 . 1
Subnet Mask Mask Length
Gateway Gateway
Primary Ca rd
MTU
Work Pattern (Modifyi ng w or k pa tt er n ne ed t o re bo ot )
4.0.0 .1.beta1
Versio n
1
2
192.1 68.1.20
192.1 68.1.38
XXX80
80
80
XXX
XXX
XXX
3.4.2
3.4.2
255.2 55.255.0
255.2 55.255.0
No.
Addre ss
EditPort
Proto col Model
Subne t Mask
3
192.1 68.2.45
XXXXXX
255.255.255.0
Quickly Add
Manually Add
Add Camera
Selected : 1/3
Add
Defau lt Password
Remain Bandwidth: 108 / 120 Mb
Cance l
Mac Address
Addre ss
Port
CE :98 :2 3 :75 :35 :22
Edit Camera
80
192 .168 . 1 . 45
255 . 255 . 2 55 . 0
admin
192 .168 . 1 . 1
Subne t Mask
Usern ame
Gatew ay
Password
OK Cancel