Quick Installation Guide

9. UPnP
10. NAT
11. Manual Recording
12. Playback
⑤ Check each camera you want to add and then click “Add” button. The DVR
will automatically add the camera(s) selected and return to “Edit Camera”
interface. “Online” status means the device connected successfully and you
will see the live image. You may select the added device and click button to
modify channel, IP address, etc.
Versio n
Edit
Upgra de
No. Camera Name
Addre ss
Port
Proto col
Model
Previ ew
Statu s
Edit Camera
IP PlanningCamera Signal
Search Camera
1
2
3
4
5
192.1 68.1.45IP Camera 1
[A01] Camera1
[A02] Camera2
[A03] Camera3
[A04] Camera4
XXX 4.1.0 .0
Onlin e
XXX
80
Camer a Name
Addre ss
Model
Edit Camera
XXX
192 .16 8 . 1 . 58
80
admin
XXX
Port
Usern ame
Proto col
Passw ord
IP Camera 1
OKTest Cancel
Sync to IPC
WAN
If your DVR has been connected correctly to your local network and you can confirm
access to the internet, you can also add remote WAN IP cameras. To add a camera,
either click on the button on a blank channel or navigate to Start>Settings>
Camera and click on “Add Camera”. Choose “Manually Add”. Enter the WAN IP
address, server port, username and password of the remote IP camera. You can test
the connection by clicking on the “Test” button and if camera tests successfully you
can add that camera.
You can take advantage of your router’s UPnP function, which can automatically
configure port forwarding.
① Navigate to Start>Settings>Network>UPnP, and enable UPnP and then click
“Apply” button to save.
② Confirm that the UPnP function is enabled in your router.
③ Click “Refresh” button to refresh the UPnP status. If the UPnP status displays
“Invalid UPnP” after refreshing it for several times, their may be a port conflict.
Please change the mapping type to “Manual” and then click to edit the port
until the UPnP status changes to ”valid UPnP”
NAT Settings
① Confirm that DVR is powered and connected to the Internet.
② Navigate to Start>Settings>Network>TCP/IP. Confirm your IP
address settings (Automatic or Manual)
③ Set the preferred or alternative DNS Server. Click “Apply” to save
the parameters. Default values are 8.8.8.8 and 4.2.2.2
④ Next, navigate to Start>Settings>Network>NAT tab. Enable NAT
and then click apply. Wait up to one minute before testing remote
connection using the QR code.
Instant Playback
Click “Instant Playback” from the right-click menu of any camera’s preview window to
select the amount of time you want to preview. When playback starts you can also click on
the progress bar to change times.
General Playback
Click on the tool bar at the bottom of the live preview interface or click Start>Playback
to enter the playback interface as shown below. The system will load up the current
cameras viewed or you can manually select which cameras you want to view. Click in the
playback window to bring up the “Add Camera” window. Select the cameras you want to
view playback on and then click “Add” to add camera.
Before recording, confirm that a HDD has been installed and formatted. From the live
interface you can access the menu toolbar. Click button to start recording. Click it again
to stop recording. You can also click to check the status of the recording.
QR Code: Click on the menu bar at the bottom of the live interface to
check the QR code or go to Start>Settings>Network>Network Status to check
the QR code (12 digits) of the DVR.
Username: The username of the DVR. The default username is admin.
Password: The password of the DVR. The password is set by yourself when you
configure the wizard for the first time.
NAT Access
After finishing configuring the NAT settings, you can enter
www.autonat.com in the address bar of your browser. If this is the first
time visiting the site, you may have to install some ActiveX plugins.
After successfully installing ActiveX, you should see the login screen
and you should be able to enter in your credentials.
HTTP Port
HTTPS Port
Server Port
80
443
6036
80
443
183.17.254.19
183.17.254.19
Valid U PnP
Valid U PnP
Valid U PnP
Invalid UPnP
6036183.17.254.19
183.17.254.19
Port Type
External Port
External Address
UPnP Stat us Edit
Port
RTSP Por t
554
554
AutoMap Typ e
UPnP
Enable
Refresh App ly
nat.autonat.com NAT Server Address
Enable
Visit Address www.autonat.com
Apply
Enter Password
Enter Username
Enter device serial number
Login
LL
oo
gg
ii
nn