PT-6VBT PT-6VAT PENTIUM II/!!! AT MAINBOARD USER’S MANUAL ( VER 2.X, 3.X ) DOC NUMBER UM-6VBT-E1 ................................................................
VIA 693/693A PENTIUM II/!!! AT MAINBOARD USER’S MANUAL ( VER 2.X, 3.X ) DOC NUMBER UM-IBT-O3 .................................................................
TABLE OF CONTENTS VIA 693/693A AT MAINBOARD TABLE OF CONTENTS Chapter & Section Page 1. INTRODUCTION ...............................................................................1-1 1.1 OVERVIEW............................................................................................... 1-1 1.2 MAINBOARD LAYOUT......................................................................... 1-2 1.3 SPECIFICATION...................................................................................... 1-3 2.
VIA 693/693A AT MAINBOARD SOMETHING IMPORTANT ! ¶ TRADEMARKS All trademarks used in this manual are the property of their respective owners. ¶ LOAD SETUP DEFAULTS “LOAD SETUP DEFAULTS” is the function which will have the BIOS default settings loaded into the CMOS memory, these default settings are the best-case values that should optimize system performance and increase system stability .This function will be necessitated when you receive this mainboard, or when the system CMOS data is corrupted.
INTRODUCTION VIA 693/693A AT MAINBOARD 1. INTRODUCTION 1.1 OVERVIEW This Mainboard is a high performance personal computer mainboard. It is the AT form-factor with Slot 1 CPU connector on the board for Pentium ™ II/!!! Processors. VIA693 or VIA693A chipset is chosen as the system core logic of the mainboard to give the most outstanding performance and reliability.
INTRODUCTION VIA 693/693A AT MAINBOARD 1.2 MAINBOARD LAYOUT CN 5 COM1 COM2 LPT CN7 CN6 USB2 USB1 JP 11 CN 15 ATX POWER AT POWER CN 14 JP1 JP 3 JP 4 JP 5 CN 13 CPU FAN CN 2 CN1 SLOT1 CN16 WOL JP 14 JP 6 JP100 JP 11 + RS HL SYS.
VIA 693/693A AT MAINBOARD 1.3 INTRODUCTION SPECIFICATION ¥ CPU Intel® Pentium™ II or Pentium™ !!! 233, 266, 300, 333. 350, 366, 400, 433, 450, 466, 500MHz and higher speed processors ¥ CPU VCC Switching mode Voltage Regulator onboard, supports +1.30V DC through +3.5V DC CPU Core Voltage. Note : The CPU Core Voltage will be Detected and adjusted automatically by the mainboard, so there is no jumper setting required to select the CPU voltage.
VIA 693/693A AT MAINBOARD INTRODUCTION ¥ WOL PORTS One WOL connector supports Wake-On-LAN (WOL up-designed) ¥ USB PORTS Two Universal Serial Bus (USB) ports. ¥ IDE PORTS Two channels of Ultra DMA/33 (or UDMA/66) Bus Master IDE ports, which will support up to 4 IDE devices like IDE hard disk, ATAPI CD-ROM etc. The IDE ports can be programmed to support PIO Mode 4, DMA mode 2 and Ultra DMA/33.
VIA 693/693A AT MAINBOARD INTRODUCTION Winbond W83783S (U2) is designed on the board to monitor hardware healthy status like system voltage, system temperature, and cooling fans. When the CPU is over heated, the system BIOS will tell the system board to give a series of beeping alarm and then slow down the CPU speed so that you can take proper action to prevent damage to your system.
VIA 693/693A AT MAINBOARD 4. Humidity 5. Altitude : 0 to 90% non-condensing. : 0 to 10,000 feet.
VIA 693/693A AT MAINBOARD INSTALLATION 2. INSTALLATION 2.1 UNPACKING The mainboard contains the following components in the package. Please inspect the following contents and confirm that everything is there in the package. If anything is missing or damaged, call your supplier for instructions before proceeding. l l l l l This mainboard. One USER‘S MANUAL. One Cable set for peripheral devices. One Pentium™ II Processor Retention Mechanism (RM). One CD diskette for device drivers and utility programs.
VIA 693/693A AT MAINBOARD INSTALLATION 2.2 AMAZING WAYS TO POWER ON THE PC SYSTEM Basically, you can connect either AT or ATX power supply to this mainboard. When the ATX power supply is connected, there are many ways to power on the system. Please read the following description for the details. POWER BUTTON The power button (PW switch) on the front panel is not only for power-on and power-off the PC system.
VIA 693/693A AT MAINBOARD INSTALLATION ¨ PS/2™ MOUSE KEY CLICK (optional) When you have a PS/2™ mouse and ATX power supply connected to the system, you may change the setup in the BIOS and use the mouse click to turn on the PC system power. To use the mouse key to turn on the PC system power, the mouse click must be done quickly and continually. Basically, 2-5 quick clicks on the mouse key ( left key or right key ) will turn the power immediately.
VIA 693/693A AT MAINBOARD INSTALLATION ¨ MODEM RING-IN ( For ATX power supply only) This mainboard can be triggered by a modem ring-in signal. When you have a external modem installed, you can use it to power on the PC system. When there is the incoming message from the external modem, the PC system will be triggered by the ring-in signal and wake up automatically to receive the message for you.
VIA 693/693A AT MAINBOARD INSTALLATION 2.3 POWER OFF THE PC SYSTEM 1. When ATX power supply is connected. There are two ways to power off the system. They are “Shut Down by Power Button” and “ Shut Down by OS”. (such as Windows® 95 and Windows® 98, you can choose the Shut Down from the file menu and the system will be powered off immediately ). 2. When AT power supply is connected. You can not use the OS to shut down the PC system, you can use only the power switch to turn the system power off.
HARDWARE SETUP VIA 693/693A AT MAINBOARD 3. HARDWARE SETUP Before you can start to install this mainboard, some hardware settings is required to make sure it will work perfectly with the component which you are going to install in your PC system. To configure this mainboard is a simple task, only a few jumpers, connectors, cables and sockets need to be selected and configured. Please refer to the following sections for the settings. 3.
VIA 693/693A AT MAINBOARD HARDWARE SETUP ( Single-Side DIMM module ) ( Double-Side DIMM Module ) 2. Minimum one DIMM module must be installed on the mainboard. 3. For PC133 M/B (VIA693A chipset). please use 3.3V PC-133 DIMM module. 4. For PC100 M/B (VIA693 chipset), please use 3.3V PC-100 DIMM module. 5. You can use single side or double side DIMM module on this mainboard. 6. Please install the DIMM module starting from DIMM2 first.
VIA 693/693A AT MAINBOARD HARDWARE SETUP (A) CN1: Keyboard Connectors Either the PS/2 (CN20) type or the AT (CN1) type keyboard connector can be installed here, ( only one connector can be installed) The factory default is the AT type connector installed on the board. When the AT type K/B installed on the board, the PS/2 type (CN20) become invisible. K/B CONNECTORS: Either PS/2 or AT type K/B connector can be installed on the mainboard.
HARDWARE SETUP VIA 693/693A AT MAINBOARD (C) CN3: COM 1 (Serial Port 1) Connector CN4: COM 2 (Serial Port 2) Connector CN 4 COM 2 CN 3 COM 1 + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC I/O address 3F8H/2F8H/3E8H/2E8H, IRQ3/IRQ4, selected by CMOS setup.
HARDWARE SETUP VIA 693/693A AT MAINBOARD (E) CN6: USB 1 (Universal Serial Bus) Connector (F) CN7: USB 2 (Universal Serial Bus) Connector 1 CN 6 2 USB 1 3 4 5 CN 7 5 4 USB 2 3 2 1 + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC Wrong USB cable will destroy the USB device or this mainboard, please contact your dealer for correct USB cable if you are installing the USB device on the mainboard..
VIA 693/693A AT MAINBOARD HARDWARE SETUP (G) CN8: Floppy Disk Control Port Connector ( using IRQ6, DMA 2): + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 CN8 FDC Connector (H) CN9: IDE 1 Connectors, (Primary IDE Port: 1F0H, IRQ 14) (I) CN10: IDE 2 Connectors, (Secondary IDE Port: 170H, IRQ 15) + RS HL -BAT 1 DIMM 3 DIMM 2 DIMM 1 FDC CN10: IDE 2 CN9: IDE 1 3-6
VIA 693/693A AT MAINBOARD HARDWARE SETUP (J) CN12: IR / FIR (Infrared Rays) Connector Consumer IR Connector ( Consumer IR connector is active only when W83977CTF-AW I/O Chip is installed on position U10 ) IR/FIR (INFRARED RAYS) ( +5VDC ) ( NO CONNECTION ) ( IR RECEIVE ) ( GROUND ) ( IR TRANSMIT ) CONSUMER IR 1 2 3 4 5 6 7 8 9 ( +5VDC ) ( IR TRANSMIT ) ( COSUMER IR RECEIVE ) ( GROUND ) CN 12 + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC (K) CN13: CPU Cooling Fan Power Connector CN13 CPU Co
VIA 693/693A AT MAINBOARD HARDWARE SETUP (L) CN14: AT Power Connector: CN 14 AT Power Connector + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC (M) CN15: ATX Power Connector: CN15 ATX Power Connector + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC 3-8
HARDWARE SETUP VIA 693/693A AT MAINBOARD (N) CN16: WOL (Wake On LAN) Connector CN 16 WOL 1 2 3 + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC Pin assignment of WOL Connector 1 2 3 Pin # Signal name Pin # Signal name 1 5V standby 2 Ground (O) CN17: Chassis Fan Power Connector + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC CN17 1 2 3 Ground + 12V DC Fan Sense Signal 3-9 Pin # Signal name 3 WOL Signal
VIA 693/693A AT MAINBOARD HARDWARE SETUP (P) Push buttons and LED connectors A series of connectors are designed on the board to connect the push buttons and LED indicators. Followings are the details: + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 P W S T L L H R L S FDC RS: Reset Button connector HL: HDD LED connector TL: Turbo LED SL: Sleep LED connector PW: Power On / Off Suspend switch 1.
VIA 693/693A AT MAINBOARD 5. HARDWARE SETUP PW Power On / Off and External Suspend Switch Connector 5-a. When this mainboard has the ATX power supply connected, According to the setup in CMOS, the PW connector has two functions. It can be the Power Switch or Suspend Switch of your PC system.(please refer to Section- 4-7 and section 4-8 for BIOS setup) Q If the setup in CMOS is “Delay 4 Sec.”, the switch function will be: A. When system is power off : Press this switch, the system will power on.
VIA 693/693A AT MAINBOARD HARDWARE SETUP 5-b. When this mainboard has the AT power supply connected, According to the setup in CMOS, the PW connector has two functions. It can be the Reset button or Suspend Switch of your PC system.(please refer to Section 2-2 and section 4-7 for BIOS setup) A. When the BIOS setup is “Delay 4 sec.”: The PW switch can be used as a suspend switch.
HARDWARE SETUP VIA 693/693A AT MAINBOARD SPK: Speaker connector 1 Pin # Signal name 1 + 5V DC 2 Speaker Data Signal 3 Speaker Data Signal 4 Speaker Data Signal 5 No Connection 5 PWR-LED & KBLOCK: Panel Power LED and Key-Lock Connector 1 Pin # Signal name 1 Pullup (+ 5V DC for Power LED) 2 Ground 3 Ground 4 Keyboard Lock 5 Ground 5 3.3 JUMPERS This section will discuss the jumper setting on this mainboard.
HARDWARE SETUP VIA 693/693A AT MAINBOARD The following jumpers which labeled with “optional” means they are optional on the mainboard and the related components are normally not populated on the board. In order to make the mainboard works properly, please make sure all jumper settings are at correct before installing this mainboard. (A) JP1: Power Supply Connector Selection (optional) This mainboard provides two power connectors to support both the AT and ATX Switching Power Supply (SPS).
VIA 693/693A AT MAINBOARD HARDWARE SETUP (B) JP2: OnNow Function Selection (optional) When JP2 is installed on the board, it will support the OnNow function. The OnNow function will allow you to use Keyboard and PS/2 mouse key click to power on the PC system. Because some certain keyboard does not support OnNow function and it will cause trouble to your PC system, should it happened, please use JP2 to disable the OnNow function so that your PC system will work normally.
HARDWARE SETUP VIA 693/693A AT MAINBOARD 1-2 USB function enabled on CN7 (USB2) (default). 2-3 USB function enabled on AGP slot.
HARDWARE SETUP VIA 693/693A AT MAINBOARD CPU Speed Ratio JP7 JP8 JP9 JP10 233/350MHz 3.5X Open Open Short Short 266/400MHz 4X Short Short Open Short 300/450MHz 4.5X Open Short Open Short 333/500MHz + RS HL DIMM 3 - Short Open Open Short 6X DIMM 2 400/600MHz DIMM 1 433/650MHz 6.5X Open Short Short Open IDE 2 IDE 1 5X 366/550MHz 5.5X Open Open Open Short FDC 466/700MHz 7X Short Short Short Open Short Open Short Open 500/750MHz 7.
HARDWARE SETUP VIA 693/693A AT MAINBOARD the default setting of JP14 will limit the Vcore at 1.3V~2.05V. Please do not change the setting on JP14 unless your CPU needs the voltage higher than 2.05V. + RS HL DIMM 3 -BAT 1 DIMM 2 DIMM 1 IDE 2 IDE 1 FDC OPEN: Vcore = 1.3V ~ 2.05V SHORT : Vcore = 1.3V ~ 3.5V.
HARDWARE SETUP VIA 693/693A AT MAINBOARD (G) JP100/JP133: FSB Clock adjustment JP100/JP133 is designed on the board for the purpose when you want to choose differtne FSB clock. You can use the setting on JP100/JP133 to force the FSB clock at 66/100/133MHz despite of the CPU type detected by the system BIOS. + RS HL -BAT 1 JP100 1 2 3 JP133 1 2 3 Note: When VIA693 chipset is installed on the mainboard, you will see only JP100 on the mainboard.
PT-6IB AWARD BIOS SETUP MAINBOARD 4. AWARD BIOS SETUP 4.1 GETTING STARTED When the system is first time powered on or reset by user, the BIOS will enter the Power On Self Test routines ( POST, which will display a copyright message on the screen and execute a diagnostics and initialization procedure.) In case that there is any error or malfunction detected, the BIOS will give a series of beep sound or display the error message on screen. When the system is normal, the simulate figure Fig.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.2 MAIN MENU ROM PCI / ISA BIOS (2A6LGP8B) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP SUPERVISOR PASSWORD BIOS FEATURES SETUP USER PASSWORD CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION POWER MANAGEMENT SETUP SAVE & EXIT SETUP PNP/PCI CONFIGURATION EXIT WITHOUT SAVING INTEGRATED PERIPHERALS LOAD SETUP DEFAULTS ESC : Quit F10 : Save & Exit Setup : Select Item (Shift)F2 : Change Color Time, Date, Hard Disk Type ... Fig.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.4 STANDARD CMOS SETUP ROM PCI / ISA BIOS (2A6LGP8B) STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm : dd : yy) : Thr, May 7 1999 Time (hh : mm : ss : 14 : 59 : 21 HARD DISKS Primary Master Primary Slave Secondary Master Secondary Slave TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Auto 0 0 0 0 0 0 Auto None 0 0 0 0 0 0 -----Auto 0 0 0 0 0 0 Auto None 0 0 0 0 0 0 ------ Drive A : 1.44M, 3.5 in.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD ROM PCI / ISA BIOS (2A6LGP8B) BIOS FEATURES SETUP AWARD SOFTWARE, INC.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD CPU Internal / External Cache : ( default setting: Enabled ) These fields allow you to turn on or turn off the Level 1 and Level 2 cache that built inside the Pentium™ II/!!! processors. CPU L2 Cache ECC Checking: ( default setting: Enabled ) This option will enable or disable the ECC checking on the CPU L2 cache. The ECC checking will ensure the accuracy of the data stored on the L2 cache.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD Memory Parity / ECC Check: ( default setting: Disabled ) This field allows you to enable or disable the system memory parity and ECC checking. Please make sure that your DIMM module has the parity bit before you will can select "Enabled" in this field. Security Option : ( default setting: Setup ) This selection field allows you to select the secure function of the PC system. There are two choice selectable - "Setup" and "System".
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.6 CHIPSET FEATURES SETUP ROM PCI / ISA BIOS (2A6LGP8B) CHIPSET FEATURES SETUP AWARD SOFTWARE, INC.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD SDRAM Cycle Length : (default setting: 3 ) The Cycle Length in this field is used to define the CAS latency. The CAS latency is one of the most important parameter in the memory subsystem because it will deci8de the system performance. Basically, the default setting “3” is the suggest parameter for this mainboard.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD System BIOS Cacheable : (default setting: Disabled) Select Enabled allows caching of the system BIOS ROM at F000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. Enabled BIOS access cached Disabled BIOS access not cached Video RAM Cacheable : (default setting: Disabled) Select Enabled allows caching of the video RAM , resulting in better system performance.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD USB Keyboard Support : (default setting: Disabled) Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The choice: Enabled, Disabled. Auto Detect DIMM/PCI Clk: ( Default setting: Enabled ) When you select “Enabled”, the mainboard will detect the presence of devices on DIMM and PCI slots.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.7 POWER MANAGEMENT SETUP ROM PCI / ISA BIOS (2A6LGP8B) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. ACPI function : Disabled Power Management : User Define PM Control by APM : Yes Video Off After : Standby Video Off Method : Blank Screen MODEM Use IRQ :3 Soft-Off by PWR-BTTN : Instant-Off.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD There are four selections for Power Management, three of which have fixed mode settings. Disable (default) Min. Power Saving Max. Power Saving User Defined No power management. Disables all four modes Minimum power management. Doze Mode = 1 hr. Standby Mode = 1 hr., Suspend Mode = 1 hr., and HDD Power Down = 15 min. Maximum power management -- ONLY AVAILABLE FOR SL CPU’S. Doze Mode = 1 min., Standby Mode = 1 min., Suspend Mode = 1 min.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD Modem Use IRQ: (Default setting: 3 ) This mainboard has the ACPI feature designed on the board and it will “wakeup” automatically when it detects the incoming modem Ring-in signal. Before you can use the Ring-in signal to wakeup your PC system, you have to install the “External” modem to your PC system and tell the PC system which serial port connects to the modem by selecting the IRQ in this field.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD LPT & COM : (Default setting: LPT/COM) When set to On (default), any event occurring at a COM(serial)/LPT (printer) port will awaken a system which has been powered down. HDD & FDD : (Default setting: ON) When set to On (default), any event occurring at a hard or floppy drive port will awaken a system which has been powered down.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.8 PNP/PCI CONFIGURATION ROM PCI / ISA BIOS (2A6LGP8B) PNP/PCI CONFIGURATION AWARD SOFTWARE, INC.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot. The choice: Enabled and Disabled.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD When Enabled, writes to the PCI bus are executed with zero wait states. Choices are Enabled, Disabled. PCI Delay Transaction : (Default setting: Enabled) The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. The choice: Enabled, Disabled. PCI#2 Access #1 Retry : (Default setting: Disabled) This item allows you enable/disable the PCI #2 Access #1 Retry.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.9 INTEGRATED PERIPHERALS ROM PCI / ISA BIOS (2A6LGP8B) INTEGRATED PERIPHERALS AWARD SOFTWARE, INC.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD Primary/Secondary Master/Slave UDMA: (Default setting: “Auto” ) Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/33, select Auto to enable BIOS support.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD Normal 4.10 LOAD SETUP DEFAULTS ROM PCI / ISA BIOS (2A6LGP8B) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP SUPERVISOR PASSWORD BIOS FEATURES SETUP USER PASSWORD CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION POWER MANAGEMENT SETUP SAVE & EXIT SETUP PNP/PCI CONFIGURATION EXIT WITHOUT SAVING INTEGRATED PERIPHERALS LOAD SETUP DEFAULTS ESC : Quit F10 : Save & Exit Setup : Select Item (Shift)F2 : Change Color Time, Date, Hard Disk Type ...
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.11 SUPERVISOR PASSWORD / USER PASSWORD ROM PCI / ISA BIOS (2A6LGP8B) CMOS SETUP UTILITY AWARD SOFTWARE, INC.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD User Password: The User Password can be used to check the user's authority. Howerver, this password entry is somewhat different to the "SUPERVISOR PASSWORD" mentioned in previous page. The User Password will have different function according to the "Supervisor Password" and the "Security Option" setup in Section 4.5: A. When there is the password stored in the "SUPERVISOR PASSWORD" 1.
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.12 IDE HDD AUTO DETECTION ROM PCI / ISA BIOS (2A6LGP8B) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP SUPERVISOR PASSWORD BIOS FEATURES SETUP USER PASSWORD CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION POWER MANAGEMENT SETUP SAVE & EXIT SETUP PNP/PCI CONFIGURATION INTEGRATED PERIPHERALS EXIT WITHOUT SAVING LOAD SETUP DEFAULTS ESC : Quit : Select Item F10 : Save & Exit Setup (Shift)F2 : Change Color Time, Date, Hard Disk Type ...
AWARD BIOS SETUP VIA 693/693A AT MAINBOARD 4.13 SAVE & EXIT SETUP / EXIT WITHOUT SAVING ROM PCI / ISA BIOS (2A6LGP8B) CMOS SETUP UTILITY AWARD SOFTWARE, INC.
