ADB-510 Page 1 7/16/2021 SENTINEL-SENSE ADB-510 INSTALLATION & OPERATION MANUAL - 041526 APPLIED WIRELESS ID
ADB-510 Page 2 7/16/2021 COPYRIGHT ACKNOWLEDGEMENTS The contents of this document are the property of Applied Wireless Identifications Group, Inc. (AWID) and are copyrighted. All rights reserved. Any reproduction, in whole or in part, is strictly prohibited. For additional copies of this document please contact: AWID 18300 Sutter Blvd Morgan Hill, CA 95037 http://www.AWID.
ADB-510 Page 3 7/16/2021 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 23 cm between the radiator & your body. This module is intended for OEM integrators only.
ADB-510 Page 4 7/16/2021 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: OGSADB510”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.
ADB-510 Page 5 7/16/2021 INDUSTRY CANADA COMPLIANCE This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
ADB-510 Page 6 7/16/2021 DETACHABLE ANTENNA USAGE This radio transmitter [IC: 6449A-ADB510] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
ADB-510 Page 7 7/16/2021 entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6449A-ADB510". Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
ADB-510 Page 8 7/16/2021 Table of Content FCC COMPLIANCE...................................................................................................................... 2 INDUSTRY CANADA COMPLIANCE....................................................................................... 5 REVISION HISTORY.................................................................................................................. 9 1. INTRODUCTION...................................................................
ADB-510 Page 9 7/16/2021 REVISION HISTORY Version No. 0.1 0.2 0.3 Revised By Date AWID Engineering AWID Engineering AWID Engineering 6/2021 7/2021 7/2021 APPLIED WIRELESS ID Sections Affected p.5 p.2, p.
ADB-510 Page 10 7/16/2021 1. INTRODUCTION AWID's Sentinel-Sense ADB-510 is a single-port, long-range Radio Frequency IDentification (RFID) reader module with 3.3 V TTL logical interface that works with most leading UHF passive tags. The reader module comes with a unique combination of long read range, small size, and low power consumption. Its primary applications are asset management and tracking, and fleet management applications. ADB-510 is delivered with Firmware Version such as US0-62.xx.xx.
ADB-510 Page 11 2. SPECIFICATIONS Input voltage Input current Idle Power Protocol language Read range RF connectors Output power Transmit frequency Receiver frequency Hopping channels Channel spacing Hopping sequence Operating temperature range Output data formats I/O Connector Dimension (*) depends on heat sink size 7/16/2021 +5.8 VDC ~ 6 VDC (max) 1.4 A max @ +6V 0.5W in stand-by ISO Type C, EPC Class 1 Gen 2 Depends on type & size of labels used MMCX (F) VSWR<1.2 @50OHMs +30 dBm max 902.60-927.
ADB-510 Page 12 7/16/2021 2.2. CONNECTOR PIN ASSIGNMENT Pin Function Pin Function 1 2 3 4 5 Reserved (*) Reserved Reserved +6.0 V +6.0 V 6 7 8 9 10 GND Unit Enable (**) SCIR (***) SCIT (***) GND (*) unit is disabled if pin 1 is low. (**) pin 7 is internally pulled high, user may leave this pin unconnected if manual control is not required. (***) SCIR receives input of reader, SCIT transmits output of reader. 2.3. MEASURING READ DISTANCE Make sure you know the tag types.
ADB-510 Page 13 7/16/2021 3. Installation & Operation Guidelines For ease of explanation, MPR reader in this section refers to an RFID device that consists of ADB-510 and a high performance circular polarized antenna inside a splash proof, UV stabilized housing case. The module should be installed on a heat sink. Example of a heat sink could be an aluminum plate of size 8”x8”x0.1” exposed to convection air flow. The screws at the bottom of module shall be used for mounting the module on the heat sink 3.
ADB-510 Page 14 7/16/2021 4. Installation Procedure This section provides installation and operation information for ADB-510 reader modules. 4.1. PARTS LIST Verify that all items listed below are present before starting the installation. o Sentinel-Sense ADB-510 o Documentation and Demo SW 2 Qty=1 Qty=1 4.2. PREPARATION FOR INSTALLATION Familiarize yourself with the connectors and pin out assignment of each I/O connectors. 4.2.1.
ADB-510 Page 15 7/16/2021 Notes on Software Programming and System Operation 4.3. SYSTEM OPERATION 4.3.1. Running a Custom Software Application or the AWID Demo Program If AWID Demo Program is not used, it is expected user will launch a Custom Software Application to send commands using AWID MPR Communication Protocol and/or the supporting SDK3 to the reader. 4.4.
ADB-510 Page 16 7/16/2021 5. Reference I. MPR Communication Protocol – Doc# 041479 II.
