Installation Guide
2
There are a variety of building wall surfaces, Awntech does not supply the hardware to install
your awning. You will need to purchase installation hardware at your local hardware store. We
have advised you on different surface applications below:
CONCRETE BLOCK WALLS: (1)1/2” masonry bit with a 3/8” shank, (4-5) 5/16”X3” Masonry
anchor bolts, 9/16” socket. You will also need a roll of weather stripping.
METAL BUILDINGS: (1) 2X6X8 #2YP Cut into 12” blocks for the back side of the metal, (4-5)
5/16”x4” lag bolts, (4-5) 5/16” washer, rubber installation strips (in the shape of the metal) and
3/8” drill bit. Bolt through the washer, the bracket and the metal into wood blocks behind the
metal. Before tightening the bracket insert the rubber strips between the building and the
awning.
ANY TYPE OF SIDING: (4-5) ¼”x4” toggle bolts, (4-5) ¼” washers, (1) Flat head screwdriver,
(1) ½” drill bit (or if you hit a stud) ; (5-8) 5/16”X4” lag bolts, (4-5) 5/16” washers, (1) 3/16” drill bit
and a 9/16” socket, you will also need a roll of weather stripping.
CONCRETE, BRICK OR STONE: (1) ½” Masonry bit with a 3/8” shank, (4-5) 5/16”x3” masonry
anchor bolts, (4) 5/16”X4” bushings, 9/16” sockets. You will also need a roll of weather
stripping.
Stucco: (4-5) ¼”X4” toggle bolts, (4-5) ¼” washers, (1) flat head screwdriver, (1) ½” drill bit (or if
you hit a stud): (4) 5/16”X4” lag bolts, (4-5) 5/16” washers, (1) 3/16” drill bit and a 9/16” socket.
You will need a roll of weather stripping.
PARTS:
Awning Size in Ft.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
(TB) Top Bar – C
Channel
1
1
1
1
2
2
2
2
2
3
3
3
3
3
3
3
3
3
(FB) Front Bar
1
1
1
1
2
2
2
2
2
3
3
3
3
3
3
3
3
3
(CNC) Cover
Support
2
2
2
3
3
3
5
5
5
5
5
5
7
7
7
7
7
7
(CNP) Projection
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(CNPA) Projection
Assembly
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(CNB) Back Bar
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(CPS) Projection
Support
2
2
2
3
3
3
5
5
5
5
5
5
7
7
7
7
7
7
(CNPM) Projection
Bar Assembly
0
0
0
0
1
1
1
3
3
3
3
3
3
5
5
5
5
5
5
Other parts: Z-Brackets, Self tapping Screws
All awning sizes over 9’ wide come in to sections. Example: Top Bar (TB) consists of TB1 &
TB2 and Front Bar (FB) consist of FB1 & FB2
Tools Required: Electrical Drill, ¼” Nut Driver Bit, Full Socket Set, Full set of Steel and
Masonry Bits, Tape Measure, Safety Glasses, 4’ Level, A Safe Ladder, #2 Pencil
YOU MAY ALSO NEED AN ASSISTANT FOR LARGER AWNINGS. IT DEPENDS ON THE
SIZE AND WEIGHT OF THE AWNING.
NOTE: YOU WILL FIND THAT THE FITTINGS HAVE BEEN PRE-INSTALLED, AS WE HAVE
PRE-ASSEMBLED AND INSPECTED IT FOR YOU IN THE FACTORY.