Installation Guide

ManualsBrandsAwntech ManualsAwningsNT33-6BBW

Nantucket Style Awnings

ASSEMBLY AND INSTALLATION INSTRUCTIONS

CAUTION: When you are opening the box keep children away. This

awning frame contains sharp metal and small hardware parts.

Choking hazard: Keep parts away from children. They may choke on

hardware. Be extremely cautious around children.

MODELS WITH VALANCE: NT22, NT33, NT44

MODELS WITH OUT VALANCE: NT22-NV, NT33-NV, NT44-NV

All the awning sizes over 9’ wide come in two sections. Example: Top Bar (TB) consists of

TB1 & TB2 and Front Bar (FB) consists of FB1 & FB2

See the chart below for the width of the awning:

Size

Width in

inches

Size

Width in

inches

3 40.5 12 148.5

4 52.5 13 160.5

5 64.5 14 172.5

6 76.5 15 184.5

7 88.5 16 196.5

8 100.5 17 208.5

9 112.5 18 220.5

10 124.5 19 232.5

11 136.5 20 244.5

OUR AWNINGS ARE DESIGNED 4.5” WIDER THAN STANDARD WINDOW/DOOR

OPENINGS SO THAT YOU WILL BE ANCHORING INTO THE STUDS AROUND THE

WINDOW OR DOOR. EXAMPLE: NT22-5 is for a 5’-0” wide window. It measures 64.5”

wide, 31” tall (24” plus 7” valance) and 24” deep (projection

Summary of content (8 pages)

PAGE 1
Nantucket Style Awnings ASSEMBLY AND INSTALLATION INSTRUCTIONS CAUTION: When you are opening the box keep children away. This awning frame contains sharp metal and small hardware parts. Choking hazard: Keep parts away from children. They may choke on hardware. Be extremely cautious around children. MODELS WITH VALANCE: NT22, NT33, NT44 MODELS WITH OUT VALANCE: NT22-NV, NT33-NV, NT44-NV All the awning sizes over 9’ wide come in two sections.
PAGE 2
Due to the fact that there is such a variety of building wall surfaces, Awntech does not supply the hardware to install your awning. You will need to purchase installation hardware at your local do-it-yourself center. We have advised you on different surface applications below: CONCRETE BLOCK WALLS: (1) ½” masonry bit with a 3/8” shank, (4-5) 5/16”x 3” masonry anchor bolts, 9/16” socket. You will also need a roll of weather stripping.
PAGE 3
NOTE: YOU WILL FIND THAT THE FITTINGS HAVE BEEN PRE-INSTALLED, AS WE HAVE PRE-ASSEMBLED AND INSPECTED IT FOR YOU IN THE FACTORY. STEP 1: Separate all of the parts by part number so they will be easy to assemble. YOU MAY ALSO NEED A HELPER DEPENDING ON THE SIZE, WEIGHT, LENGTH AND HEIGHT OF THE AWNING NOTE: YOU WILL FIND THAT THE FITTINGS HAVE BEEN PRE-INSTALLED, AS WE HAVE PRE-ASSEMBLED AND INSPECTED IT FOR YOU IN THE FACTORY. ASSEMBLING THE FRAME STEP 2: Connect Front Bar (FB) to (2) Back Bars (B).
PAGE 4
POSITIONING THE BRACKETS CORRECTLY ON THE WALL STEP 13: Place the awning on the wall and make adjustments to choose the ideal location. Mark the bottom of the frame after you have centered it on the opening that you are covering. STEP 14: Using a pencil and a level, mark a horizontal line as wide as your awning at that height. Verify that it is centered on the space. STEP 15: From the inside of the awning, make (2) marks on the wall 6” up from that line where the awning frame touches the wall.
PAGE 5
WARRANTY 5-Year Limited Manufacturer's Warranty A. WHO GIVES THIS WARRANTY? Awntech Corporation B. WHO IS ENTITLED TO THIS WARRANTY? This Warranty applies only to the original purchaser who paid for the product and may not be assigned or transferred to subsequent owners. This Warranty applies only to products purchased and installed in the US. C.
PAGE 6
4. DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS, AND YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE. G. RETURNS, DAMAGES RETURN QUALIFICATION: You can only return a product if it is defective upon arrival. If you simply do not like the product or if you did not measure correctly, you will only be qualified for a merchandise credit and you will be required to pay for shipping the product back to Awntech in restockable condition.
PAGE 7
This frame must be assembled on the ground.
PAGE 8