Use and Care Guide

Due to the fact that there is such a variety of building wall surfaces,
Awntech does not supply the hardware to install your awning. You
will need to purchase installation hardware at your local do-it-
yourself center. We have advised you on different surface
applications below:
CONCRETE BLOCK WALLS: (1) ½” masonry bit with a 3/8” shank, (4-5) 5/16”x 3”
masonry anchor bolts, 9/16” socket. You will also need a roll of weather stripping.
METAL BUILDINGS: (1) 2x6x8 #2YP cut into 12” blocks for the back side of the
metal, (4-5) 5/16”x 4” lag bolts, (4-5) 5/16” washers, rubber installation strips (in the
shape of the metal) and a 3/8” drill bit. Bolt through the washer, the bracket and the
metal into wood blocks behind the metal. Before tightening the bracket insert the rubber
strips between the building and the awning.
ANY TYPE OF SIDING: (4-5) ¼”x 4” toggle bolts, (4-5) ¼” washers, (1) Flat head
screwdriver (1) ½ drill bit (or if you hit a stud): (5-8) 5/16”x4” lag bolts, (4-5) 5/16”
washers, (1) 3/16” drill bit and a 9/16” socket. You will also need a roll of weather
stripping.
CONCRETE, BRICK OR STONE: (1) ½ masonry bit with a 3/8” shank, (4-5) 5/16”x
3” masonry anchor bolts, (4-5) 5/16”x1/4” bushings, 9/16” socket. You will also need a
roll of weather stripping.
STUCCO: (4-5) ¼”x 4” toggle bolts, (4-5) ¼” washers, (1) Flat head screwdriver (1) ½
drill bit (or if you hit a stud): (4) 5/16”x4” lag bolts, (4-5) 5/16” washers, (1) 3/16” drill
bit and a 9/16” socket. You will also need a roll of weather stripping
.
• Please read the instructions fully before assembly.
• This awning is designed to be assembled on the wall.
PARTS:
Awning Size in Ft. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
(TB) Top Bar - C Channel 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2
(FB) Front Bar 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2
(NC)Hypotenuse / Cover Support 2 2 2 3 3 3 4 4 5 5 5 5 5 7 7 7 7 7
(BP) Black Projection Bar 2 2 2 3 3 3 4 4 5 5 5 5 5 7 7 7 7 7
Other parts Self tapping screws, Z-brackets
Tools Required: Electrical Drill, ¼” Nut Driver Bit, Full Socket Set, Full set of Steel
and Masonry Bits, Tape Measure, Safety Glasses, 4’ Level, A Safe Ladder, #2 Pencil
YOU MAY ALSO NEED AN ASSISTANT FOR LARGER AWNINGS. IT DEPENDS ON
THE SIZE AND WEIGHT OF THE AWNING.
NOTE: YOU WILL FIND THAT THE FITTINGS HAVE BEEN PRE-INSTALLED, AS WE
HAVE PRE-ASSEMBLED AND INSPECTED IT FOR YOU IN THE FACTORY.