Ver.
Steps To Test Run Before Installation IMPORTANT! Wear gloves to protect against sharp edges. PLEASE FOLLOW THESE INSTRUCTIONS TO TEST THE RANGE HOOD BEFORE INSTALLATION FOR ANY DEFECTS OR SHIPPING DAMAGE: 1. 2. 3. 4. 5. 6. 7. Remove the range hood and accessories from the package carefully. Place the range hood on a flat stable surface, remove the baffle filter and check for any dents or damages on the range hood body. Remove the loosen parts if there's any.
Table of Contents Important Safety Instructions 4 Installation Preparations 5 Venting Requirements 5 Venting System Setup 5 Duct Run Minimum Size 6 Electrical Requirement 6 Installation 7 Installing the Range Hood 7 Connecting the Vent System 7 Electrical Connection 7 Installing the Oil Collector 8 Installing the Baffle Filters 8 Completing the Installation 8 Range Hood Use
IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, PLEASE READ THE FOLLOWING CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE RANGE HOOD: • • • • • • • • • • Always disconnect, lock and tag the power source before installing or servicing the range hood. Failure to do so may result in fire, shock or serious injury.
INSTALLATION PREPARATIONS Venting Requirements DO • • • • • • • • • DO NOT Have the venting system go vertically from the range hood to the roof if possible. Have 24"-30" distance between the cooktop and the range hood. 27" is recommended. Use uniformed duct of 8" round duct. Use metal vent only. Rigid metal vent is recommended. Semi-rigid aluminum vent is also acceptable for easy connection. Make sure there is a minimum of 24" of straight vent between the elbows if more than 1 elbow is used.
INSTALLATION PREPARATIONS IMPORTANT! • • • • • If long duct run is needed, increase the duct size from 8" to 9" or 10". If a reducer is needed, use a long reducer instead of a pancake reducer and install it as far away from the range hood as possible. Reducing the duct size will restrict and decrease the speed of the airflow and hense lower the range hood's performance.
INSTALLATION INSTALLATION INSTRUCTIONS CAUTION CAUTION! Wear gloves to protect against sharp edge. Make sure the range hood is securely mounted before releasing. Installing the Range Hood • • For installing under the cabinet with recessed bottom, attach a 4" wide wood filler strip (not provided) on each side. For a more secure installation, install additional screws into the pre-drilled holes on the backplate of the range hood to secure it to the studs or lumbers.
INSTALLATION • Reconnect the power. Installing the Baffle Filters Installing the Oil Container • • • Locate 2 Brackets at the hood bottom, one on each side, near the back of the range hood. • Peel off the protective film from the baffle filters if there's any. Align the baffle filter's bottom pins to the holes on the hood. (Step 1) Pull and hold the latch. The top pins of the baffle filter will retrack into the filter while the latch is pulled.
RANGE HOOD USE Range Hood Control Panel • Remote Control Delayed Auto Sensor Shut Off Light When the Delayed Auto Shut Off fuction is activated while the blower is running, a countdown timer will show up in the LCD Display. Light • Speed Power Remote Control Sensor • • The Remote Control Sensor receives infrared (IR) signal from the remote control. The maximum distance for IR data transmission is 10 feet and requires direct line of sight.
RANGE HOOD CARE Cleaning • WARNING • • To reduce the risk of electrical shock, DO NOT clean the hood while it's operating. Never put your hands into the area housing the fan when the fan is operating. • • front, align and insert the filter. Pull the spring release handle and push the filter into position. Release the handle. Repeat the steps for the remaining filters.
RANGE HOOD TROUBLESHOOTING Before Calling for Service Issue The range hood doesn't turn on • Possible Cause / Solution Check if the range hood is plugged in. Make sure that all power is turned ON, the fuse isn't blown and all electrical wirings are properly connected. The range hood turns on but the LED light doesn't • Replace the defective LED assembly. Refer to Range Hood Care section for instructions.
WARRANTY This product is warranted for a limited period of ONE YEAR Parts and Labor, begins from the date of purchase. • This limited warranty is applied to the original retail purchaser and valid only for products purchased for home use in the continental United States of America. • • This limited warranty is non-transferable and does not extend to the subsequent owners of this product.
Website: www.awoco.
