User's Manual

ManualsBrandsAxcess International ManualsElectronicsAT132-AT Activator

Table Of Contents

General Installation Information
- Safety
- Information Flags
- Hand Tools, Equipment and Materials
  - Required
  - Recommended
A
ActiveTag System Overview
- ActiveTag System Components
- Tags
- Activator
- Receiver
- Transmit Antennas
  - Types of Transmit Antennas
System Configuration Basics
- Introduction
- Application Types
  - Vehicle
    - System Placement Guidelines
  - Personnel and/or Asset
    - System Placement Guidelines
- Multiple Activator Applications
- Installation Tips
- Basic Installation Steps
C
Configuring and Installing the Activator
- Introduction
  - Activator IDs
- Supplying Power
- Setting the Activator ID
  - Method 1: Serial Commands
  - Method 2: Hardware
- Other Serial Port Commands
- Activator Installation
  - Required Materials
  - Mounting the Activator
- Resizing the Activation Field
  - Adjusting the Field
C
Configuring the Receiver
- Introduction
- Connecting Power to the Receiver
- Configuring the Receiver
- Receiver Responses
- Setting up a Wiegand System
  - Responding to Activator IDs
  - Alarm Output
- Setting up a Serial or LAN System
- Setting the Receiver ID
- Enabling TTL outputs (Logic Control)
- Diagnostic Mode
  - _
  - Turning off Diagnostic Mode
- Viewing Configuration Settings
C
Configuring the NIU
- Introduction
- Connecting the NIU to the PC
- Setting up the Serial Port
- Connecting the Receiver and the NIU
- Modifying the NIU Configuration
I
Installing the Receiver
- Connecting to a Wiegand Control Panel
  - Wiegand Output
- Connecting to a Serial Device
  - Serial Output
- Wiring TTL Outputs to TTL outputs
- Connecting to the NIU and the Network
- Mounting the Receiver
  - Mounting the Receiving Antenna Separately
Road Loop Antenna Installation
- Introduction
- Required Materials
- Prerequisite Tasks
- Road Loop Layout & Connecting to the Activator
- Installing the Road Loop Antenna (Frequently contracted)
B
Bar Antenna Installation
- Introduction
- Prerequisite Tasks
- Installation Considerations
- Installing the Bar Antenna
P
Picture Frame Antenna Installation
- Introduction
- Prerequisite Tasks
- Installing the Picture Frame Antenna
T
Tags
- Types of Tags
- Tag Labeling
- The LED Test Tag
- Mounting Tags to Assets
- Mounting Tags to Vehicles
- Tags and Personnel
  - Required Materials
  - Operating Panic Tags
Appendix A: Troubleshooting the System
- _
A
Appendix B: Coaxial Cable
A
Appendix C: Advanced Wiegand Configuration
- _
  - Setting the Time between Outputs
  - Changing the Duplicate Tag Buffer
Appendix D: Receiver Commands
Appendix E: Specifications
- _
I
Index

Configuring the Receiver

Introduction

The Receiver receives the Tag’s broadcast signal via its receiving

antenna and sends the Tag data to a PC or control device based on

how it has been programmed to respond to the Activator ID.

PWRLF UHF

RX TX

DATA

AUX

RX TX

ActiveTag

Network Receiver

Figure 16 Front of the Receiver

5VDC

GND

24VDC

+5VGD1D0

Power

Wiegand

Output

RS-232

Figure 17 Back of the Receiver

Connecting Power to the Receiver

All Receivers come with a 5 VDC, 400 mA power transformer that

plugs into a 110 VAC outlet. If uninterruptible power is an issue, a

backup battery or UPS can be used. When power is supplied to the

Receiver, the power indicator LED on the front will light up.

Step 1:

Ensure that the 110 VAC outlet is near the Receiver and is

easily accessible.

Step 2:

Plug the AC adapter into the jack labeled

5VDC

on the

back

of the Receiver (Figure 17).

Step 3:

Plug the unit into the power outlet.