User's Manual

ManualsBrandsAxcess International ManualsElectronicsAT132-AT Activator

Table Of Contents

General Installation Information
- Safety
- Information Flags
- Hand Tools, Equipment and Materials
  - Required
  - Recommended
A
ActiveTag System Overview
- ActiveTag System Components
- Tags
- Activator
- Receiver
- Transmit Antennas
  - Types of Transmit Antennas
System Configuration Basics
- Introduction
- Application Types
  - Vehicle
    - System Placement Guidelines
  - Personnel and/or Asset
    - System Placement Guidelines
- Multiple Activator Applications
- Installation Tips
- Basic Installation Steps
C
Configuring and Installing the Activator
- Introduction
  - Activator IDs
- Supplying Power
- Setting the Activator ID
  - Method 1: Serial Commands
  - Method 2: Hardware
- Other Serial Port Commands
- Activator Installation
  - Required Materials
  - Mounting the Activator
- Resizing the Activation Field
  - Adjusting the Field
C
Configuring the Receiver
- Introduction
- Connecting Power to the Receiver
- Configuring the Receiver
- Receiver Responses
- Setting up a Wiegand System
  - Responding to Activator IDs
  - Alarm Output
- Setting up a Serial or LAN System
- Setting the Receiver ID
- Enabling TTL outputs (Logic Control)
- Diagnostic Mode
  - _
  - Turning off Diagnostic Mode
- Viewing Configuration Settings
C
Configuring the NIU
- Introduction
- Connecting the NIU to the PC
- Setting up the Serial Port
- Connecting the Receiver and the NIU
- Modifying the NIU Configuration
I
Installing the Receiver
- Connecting to a Wiegand Control Panel
  - Wiegand Output
- Connecting to a Serial Device
  - Serial Output
- Wiring TTL Outputs to TTL outputs
- Connecting to the NIU and the Network
- Mounting the Receiver
  - Mounting the Receiving Antenna Separately
Road Loop Antenna Installation
- Introduction
- Required Materials
- Prerequisite Tasks
- Road Loop Layout & Connecting to the Activator
- Installing the Road Loop Antenna (Frequently contracted)
B
Bar Antenna Installation
- Introduction
- Prerequisite Tasks
- Installation Considerations
- Installing the Bar Antenna
P
Picture Frame Antenna Installation
- Introduction
- Prerequisite Tasks
- Installing the Picture Frame Antenna
T
Tags
- Types of Tags
- Tag Labeling
- The LED Test Tag
- Mounting Tags to Assets
- Mounting Tags to Vehicles
- Tags and Personnel
  - Required Materials
  - Operating Panic Tags
Appendix A: Troubleshooting the System
- _
A
Appendix B: Coaxial Cable
A
Appendix C: Advanced Wiegand Configuration
- _
  - Setting the Time between Outputs
  - Changing the Duplicate Tag Buffer
Appendix D: Receiver Commands
Appendix E: Specifications
- _
I
Index

Tags

68 750.001.004 R0033 © 2001 AXCESS Inc.

Metal Mount Equipment Tag

Same as the Harsh Environment Tag except its robust design is

suitable for exterior mounting direct to metal surfaces. It attaches to

metal using screws or rivets through two 1/8" mounting holes. The

Metal Mount Tag does not have an LED.

Tag Labeling

The Tag is labeled on its beveled edge. The format for labeling is as

follows:

FCCID:N6E-132-TAG VnnYYMXXTTTTT

where:

FCCID:N6E-132-TAG

FCC information

Vnn

Tag version

YY

Last two digits of the year of manufacture.

M

Month the Tag was made. A, B and C

represent October, November and

December, respectively. Other months are

represented by standard numeric

convention (1 for January, etc.)

XX

Site code, in hexadecimal format. At

present, this value is 19 for site code 25.

TTTTT

Factory ID, a unique preprogrammed ID

number that is stored permanently in the

Tag.

Note: The actual ID number may vary for

custom programmed Tags. The custom ID

number, if any, will be printed on the other

beveled edge.