User's Manual

ManualsBrandsAxcess International ManualsElectronicsAT132-AT Activator

Table Of Contents

General Installation Information
- Safety
- Information Flags
- Hand Tools, Equipment and Materials
  - Required
  - Recommended
A
ActiveTag System Overview
- ActiveTag System Components
- Tags
- Activator
- Receiver
- Transmit Antennas
  - Types of Transmit Antennas
System Configuration Basics
- Introduction
- Application Types
  - Vehicle
    - System Placement Guidelines
  - Personnel and/or Asset
    - System Placement Guidelines
- Multiple Activator Applications
- Installation Tips
- Basic Installation Steps
C
Configuring and Installing the Activator
- Introduction
  - Activator IDs
- Supplying Power
- Setting the Activator ID
  - Method 1: Serial Commands
  - Method 2: Hardware
- Other Serial Port Commands
- Activator Installation
  - Required Materials
  - Mounting the Activator
- Resizing the Activation Field
  - Adjusting the Field
C
Configuring the Receiver
- Introduction
- Connecting Power to the Receiver
- Configuring the Receiver
- Receiver Responses
- Setting up a Wiegand System
  - Responding to Activator IDs
  - Alarm Output
- Setting up a Serial or LAN System
- Setting the Receiver ID
- Enabling TTL outputs (Logic Control)
- Diagnostic Mode
  - _
  - Turning off Diagnostic Mode
- Viewing Configuration Settings
C
Configuring the NIU
- Introduction
- Connecting the NIU to the PC
- Setting up the Serial Port
- Connecting the Receiver and the NIU
- Modifying the NIU Configuration
I
Installing the Receiver
- Connecting to a Wiegand Control Panel
  - Wiegand Output
- Connecting to a Serial Device
  - Serial Output
- Wiring TTL Outputs to TTL outputs
- Connecting to the NIU and the Network
- Mounting the Receiver
  - Mounting the Receiving Antenna Separately
Road Loop Antenna Installation
- Introduction
- Required Materials
- Prerequisite Tasks
- Road Loop Layout & Connecting to the Activator
- Installing the Road Loop Antenna (Frequently contracted)
B
Bar Antenna Installation
- Introduction
- Prerequisite Tasks
- Installation Considerations
- Installing the Bar Antenna
P
Picture Frame Antenna Installation
- Introduction
- Prerequisite Tasks
- Installing the Picture Frame Antenna
T
Tags
- Types of Tags
- Tag Labeling
- The LED Test Tag
- Mounting Tags to Assets
- Mounting Tags to Vehicles
- Tags and Personnel
  - Required Materials
  - Operating Panic Tags
Appendix A: Troubleshooting the System
- _
A
Appendix B: Coaxial Cable
A
Appendix C: Advanced Wiegand Configuration
- _
  - Setting the Time between Outputs
  - Changing the Duplicate Tag Buffer
Appendix D: Receiver Commands
Appendix E: Specifications
- _
I
Index

Tags

72 750.001.004 R0033 © 2001 AXCESS Inc.

Step 4:

Mark the spot you found on the windshield with some

scotch tape or a washable marker.

Note: The LED light can be hard to see in bright daylight.

Shield the LED with your hand while holding it against the

windshield.

Step 5:

Test the various positions to find the one that works best

for your installation and the vehicles involved.

Mounting a Vehicle Tag

Step 1:

Apply mounting tape/Velcro on the back of the Tag. Push

the mounting tape/Velcro securely on the back of the Tag.

IMPORTANT!

To receive maximum range from the

antenna, the Tag must be mounted with the back of the

Tag facing the glass at least 3 inches from the dashboard.

Step 2:

If using Velcro, apply one side of the Velcro mount to the

location where the LED Tag was successfully tested. Then

mount the Tag with the other piece of Velcro onto the

Velcro on the windshield.

Step 3:

If using double-sided tape, peal the cover off the double-

sided tape attached to the Tag. Firmly apply the Tag to the

windshield location you found earlier and press the Tag to

the windshield ensuring solid contact.