User's Manual

ManualsBrandsAxcess International ManualsElectronicsAT132-AT Activator

Table Of Contents

General Installation Information
- Safety
- Information Flags
- Hand Tools, Equipment and Materials
  - Required
  - Recommended
A
ActiveTag System Overview
- ActiveTag System Components
- Tags
- Activator
- Receiver
- Transmit Antennas
  - Types of Transmit Antennas
System Configuration Basics
- Introduction
- Application Types
  - Vehicle
    - System Placement Guidelines
  - Personnel and/or Asset
    - System Placement Guidelines
- Multiple Activator Applications
- Installation Tips
- Basic Installation Steps
C
Configuring and Installing the Activator
- Introduction
  - Activator IDs
- Supplying Power
- Setting the Activator ID
  - Method 1: Serial Commands
  - Method 2: Hardware
- Other Serial Port Commands
- Activator Installation
  - Required Materials
  - Mounting the Activator
- Resizing the Activation Field
  - Adjusting the Field
C
Configuring the Receiver
- Introduction
- Connecting Power to the Receiver
- Configuring the Receiver
- Receiver Responses
- Setting up a Wiegand System
  - Responding to Activator IDs
  - Alarm Output
- Setting up a Serial or LAN System
- Setting the Receiver ID
- Enabling TTL outputs (Logic Control)
- Diagnostic Mode
  - _
  - Turning off Diagnostic Mode
- Viewing Configuration Settings
C
Configuring the NIU
- Introduction
- Connecting the NIU to the PC
- Setting up the Serial Port
- Connecting the Receiver and the NIU
- Modifying the NIU Configuration
I
Installing the Receiver
- Connecting to a Wiegand Control Panel
  - Wiegand Output
- Connecting to a Serial Device
  - Serial Output
- Wiring TTL Outputs to TTL outputs
- Connecting to the NIU and the Network
- Mounting the Receiver
  - Mounting the Receiving Antenna Separately
Road Loop Antenna Installation
- Introduction
- Required Materials
- Prerequisite Tasks
- Road Loop Layout & Connecting to the Activator
- Installing the Road Loop Antenna (Frequently contracted)
B
Bar Antenna Installation
- Introduction
- Prerequisite Tasks
- Installation Considerations
- Installing the Bar Antenna
P
Picture Frame Antenna Installation
- Introduction
- Prerequisite Tasks
- Installing the Picture Frame Antenna
T
Tags
- Types of Tags
- Tag Labeling
- The LED Test Tag
- Mounting Tags to Assets
- Mounting Tags to Vehicles
- Tags and Personnel
  - Required Materials
  - Operating Panic Tags
Appendix A: Troubleshooting the System
- _
A
Appendix B: Coaxial Cable
A
Appendix C: Advanced Wiegand Configuration
- _
  - Setting the Time between Outputs
  - Changing the Duplicate Tag Buffer
Appendix D: Receiver Commands
Appendix E: Specifications
- _
I
Index

Appendix E: Specifications

Sequential Command List

<number>D set control TTL output 1 signal duration time in seconds (0-255,5)

<number>E set control TTL output 2 signal duration time in seconds (0-255,5)

set Device ID for Network Receiver (0-999)

<number>L set tag redundancy buffer time in tenths of seconds (0-255, 125)

<number>T set time between tag read outputs in tenths of seconds (0-255, 13)

<number>W set single valid Wiegand Activator ID (1-250, 127)

<number>+ add new Device ID or Status Code to Valid ID list (0-255, max 34)

<number>- delete a Device ID or Status Code to Valid ID list (0-255, min. 1 entry)

10c turn on TTL output 1 now

11c turn on TTL output 2 now

12c set Wiegand alarm output to OFF

13c set TTL output 1 alarm flag to OFF

14c set TTL output 2 alarm flag to OFF

15c set Wiegand output to ON

16c set TTL output 1 valid read flag to OFF

17c set TTL output 2 valid read flag to OFF

18c set tag read serial output to ON

19c set Wiegand Activator ID filter to ON

20c set Wiegand/TTL output interrupts to ON

21c set serial output to the long format (RRRAAAFFFTTTTT)

22c set serial diagnostics output to OFF

23c set serial data rate to 4800 baud

24c set serial data rate to 9600 baud

25c set serial data rate to 19200 baud

26c set Wiegand alarm output to ON

27c set TTL output 1 alarm flag to ON

28c set TTL output 2 alarm flag to ON

29c set Wiegand output to OFF

30c set TTL output 1 valid read flag to ON

31c set TTL output 2 valid read flag to ON

32c set tag read output to OFF

33c set Wiegand Activator ID filter to OFF

34c set Valid ID list to default values (per V5 list)

35c set Wiegand/TTL output interrupts to OFF

36c set serial output to short format (AAAFFFTTTTT)

37c clear Valid ID list (except 127)

38c return and display current configuration data

39c set serial diagnostics output to ON

40c return and display Supervisory data