User Manual
Table Of Contents
- 1. INTRODUCTION
- Scope and Purpose of Document
- Limitation of Liability Notice
- 2. SAFETY CONSIDERATIONS
- 3. EQUIPMENT OVERVIEW
- 4. SUB-UNIT MODULES
- 4.1 Bandpass Filter (02-010201)
- 4.2 Two-Way Splitter (07-002503)
- 4.3 0.25Watt 0- -30dB Switched Attenuator (10-000703)
- 4.4 11-007302 & 11-007402 Low Noise Amplifiers
- 4.4.1 Description
- 4.4.2 Technical Specification (11-007302)
- 4.4.3 Technical Specification (11-007402)
- 4.4.4 LNA ‘D’ Connector Pin-out details
- 4.4.5 Drg. # 11-007302, LNA Assembly With Alarm Relay
- 4.4.6 Drg. # 11-007370, LNA RF Circuit Diagram
- 4.4.7 Drg. # 11-007371, LNA DC Wiring Diagram
- 4.4.8 Drg. # 11-003971, LNA DC Circuit Diagram
- 4.4.9 Drg. # 11-007402, LNA Assembly With Alarm Relay
- 4.4.10 Drg. # 11-007470, LNA RF Circuit Diagram
- 4.5 12-021601 5Watt Medium Power Tetra Amplifier
- 4.6 12-022101 10Watt Power Tetra Amplifier
- 4.7 8A Mains Filter Assembly (13-003301)
- 4.8 Channel Control Module (17-002101)
- 4.9 Channel Selective Module (17-003007)
- 4.10 12V Single Relay Board (80-008901)
- 4.11 12V Switch-Mode PSU (96-300052)
- 5. INSTALLATION
- 6. FAULT FINDING & MAINTENANCE
- 6.1 General Fault Finding Procedures
- 6.2 Downlink
- 6.3 Uplink
- 6.4 Fault repair
- 6.5 Checking service
- 6.6 Service Support
- 6.7 Tools & Test Equipment
- 6.8 General Maintenance Procedures
- _
- 6.9 Module Removal (LNA’s, general procedure)
- 6.10 Module Replacement (general)
- 6.11 Power Amplifiers
- 6.12 Low Power Amplifier Replacement
- 6.13 Module Transportation
- APPENDIX A
- _
- APPENDIX B
Two Channel UHF Cell Enhancer
User Handbook
Handbook Number: 50-187601HBKM Page: 49 of 51
Glossary of Terms
Repeater or
Cell Enhancer
A Radio Frequency (RF) amplifier which can simultaneously
amplify and re-broadcast Mobile Station (MS) and Base
Transceiver Station (BTS) signals.
Band Selective
Repeater
A Cell Enhancer designed for operation on a range of channels
within a specified frequency band.
Channel Selective
Repeater
A Cell Enhancer, designed for operation on specified channel(s)
within a specified frequency band. Channel frequencies may be
factory set or on-site programmable.
AC Alternating Current
AGC Automatic Gain Control
BBU Battery Backup Unit
BTS Base Transceiver Station
CEMS Coverage Enhanced Management System
C/NR Carrier-to-Noise Ratio
DC Direct Current
Downlink (D/L) RF signals Tx from the BTS to the Master Site
FO Fibre Optic
GND Ground
ID Identification Number
LED Light Emitting Diode
LNA Low Noise Amplifier
LPA Low Power Amplifier
MOU Master Optical Unit
M.S. Mobile Station
MTBF Mean Time Between Failures
N/A Not Applicable
N/C No Connection
OFR On Frequency Repeater
OIP3 Output Third Order Intercept Point = RFout +(C/I)/2
PA Power Amplifier
RF Radio Frequency
RSA Receiver/Splitter Amplifier
Rx Receiver
S/N Serial Number
Tx Transmitter
Uplink (U/L) RF signals transmitted from the MS to the BTS
VSWR Voltage Standing Wave Ratio
WDM Wave division multiplex