AXW-D800 / AXW-D1900 CDMA 1xEVDO Wireless Broadband Modem User Manual
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 User ID and Password You may need to enter the user ID and password in order to use the 1xEV-DO Modem Please write User ID and Password for future need. Keep this manual in a secure place.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Table of Contents Package Contents……………………………………………………. …... Introduction…………………………………………………………………. Features…………………………………………………………………….. Safety Precaution………………………………………………………….. Basic Installation…………………………………………………………… Getting to know the EV-DO modem……………………………………… Connection using Ethernet port…………………………………………... Configuring Your PC………………………………………………………. Configuring Ethernet Connection………………………………………… Connection using USB port……………………………………………….
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Package Contents After opening the package, check to make sure that you have all the parts shown below. If any piece is missing or broken, please call customer service.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Introduction Axesstel 1xEv-DO Broadband EV-DO modem allows users to "get connected" to high speed data services with unprecedented ease. Powered by the latest QUALCOMM MSM6500 processor, this wireless broadband modem provides high speed data service through USB or Ethernet interfaces at rates of up to 2.4Mbps download and 153.6 Kbps upload.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Safety Precaution 1. Avoid placing the unit in a dusty location, or near a source of gas or fire. 2. Do not shake, hit or drop the unit. 3. To clean the unit, use only a soft, dry cloth. The chemicals in alcohol, benzine or acetone can damage the surface of the unit. 4. Do not twist or pull the cord out of the unit. 5. Do not disassemble the phone. 6.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Getting to know the EV-DO modem Power Switch Power Switch is located on the front side of the EV-DO modem. Turn on the unit by moving switch to ON position (O). Turn off the unit by moving switch to OFF position (|). NOTE: When you turn on the EV-DO modem, it automatically searches for service signal. When it successfully acquires service signal, the signal LED turns to green, orange or red depending on signal strength.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Connection using Ethernet port 1. Power off the unit before connecting the cables. 2. Connect CAT-5 Ethernet cable to Ethernet port of EV-DO Modem. 3. Connection type switch next to the Ethernet port should be set to Ethernet. If not, slide the switch toward the Ethernet port. 4. Connect other end of Ethernet cable to the RJ-45 connector of Ethernet network adapter or a network device. 5.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 2. Double click the Network Connection icon. 3. Go to Local Area Connection Properties.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 4. Select the “Internet Protocol (TCP/IP)” 1. If there is no TCP/IP line listed, you will need to install TCP/IP first. 5. Press the “Properties” button. 6. Check “Obtain an IP address automatically” 7. Check “Obtain DNS Server address automatically”. 8. Click Ok to exit Properties. 9. If asked to re-start the PC, click “YES”.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Configuring Ethernet Connection EV-DO modem provides an embedded Web-based Management Utility. Configure your EV-DO modem by using your Web Browser. Please refer to Web-based Manager section. Log In Open your Web browser and enter 192.168.0.1 in the address bar When prompt for User name and password, enter the following user id and password.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 1. Click on the “Network” tab. 2. Under “Local Area Network Setup”, Select “DHCP Server->Enable” to enable Dynamic IP assignments. 3. Under “PPP Configuration”, enter login User ID and Password of the account. Choose type of Authentication process used by the network. Enter access dial number of login account. 4. Press “APPLY” button. 5. Turn off and turn on the terminal. 6. Log in and check if the information you have entered are correctly shown.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Connection using USB port USB Driver Installation (Part 1) Run Setup from the CD Run the Setup program on the USB Driver CD. It is important that you should run the setup before connecting the USB cables to your PC. 1. Run the setup. Make sure that the USB cable is not yet connected. z If you wish to change the location of the files, press “Browse” and select location. 2. Otherwise, press “Next”.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 z If you wish to change the START Menu location, change the name of the folder. 3. Otherwise, press “Next” z If you do not wish to restart the window, but restart later, check “No, I will restart my computer later.” 4. Otherwise, press Finish. USB Driver Installation (Part 2) Preparation 1. Turn off both the EV-DO modem and your PC. 2. Connect the included USB Cable to USB port on your PC. 3.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 USB Driver Installation (Part 3) Driver Installation 1. Power on the PC. After the boot up process, you will see “Found New Hardware” screen. 2. The New Hardware Wizard may recognize the name by itself. Or you may have to select from a list. 3. Select “Qualcomm Multimedia USB Modem”. 4. When you encounter this window, press “Continue Anyway”.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 5. Press “Finish”. Connection Using USB connection. After USB driver has been installed, follow following steps to connect to the 1`xEV-DO network. 1. Open Network Connections from the Start Menu or Control Panel.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 2. Double click “AxessD2” connection item. Make sure that the modem associated with the connection is “Qualcomm Multimedia USB Modem”. 2. Enter User name and Pasword. z Check “Save this user…” if you do not wish to enter the user name and password every time you use the EVDO modem. 3. On you first use, press “Properties” button to check if all settings are correct. 4. Make sure to enter the dial number as well.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 3. Check that the correct modem is select. 4. Check “Show icon in notification area when connected” z If a wrong modem is select, connection attempt will fail. 5. Your PC is trying to connect to the EV-DO network. If failed check each step of this section and try again.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 To disconnect USB connection 1. To disconnect the EV-DO connection, Select “Disconnect” from the Tray Icon Area. 2. If the tray icon is not visible, open the “Network Connections” and select the “AxessD2” connection item. 3. Right click on the icon and select “Disconnect”.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Advanced Menu: Web Admin Tool EV-DO modem provides an embedded Web-based Management Utility. This utility is operating system independent. Configure your EV-DO modem by using your Web Browser. Log In 1. Open your Web browser 2. Enter 192.168.0.1 in the address bar as in the diagram. z The default IP address of the EV-DO modem is 192.168.0.1.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 System Host Name Change Password System Upgrade Restore Default Reboot System - 21 - Name of the EV-DO modem. You may change this name according to your network need. To change the password of your account, enter your old password and new password. To download new firmware. Restore all settings to factory default settings. Restart EV-DO modem.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Network IP Address Subnet Mask DHCP Server DHCP Server IP Range IP address of EV-DO modem. Subnet Mask Enable if using Dynamic IP Address. Range of IPs that can be assigned by the DHCP Server to each PC. DNS IP Address PPP Configuration APPLY IP address of DNS Server provided by your Service Provider. Enter User ID, Password, Authentication type, and dial number of your wireless data network account.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Security Firewall Support Client Filtering Packet Forward MAC Filtering DMZ Server Blocking WAN Ping APPLY - 23 - Enable/Disable built-in firewall feature. Local Client PC group can not access specified remote application. Enable specific ports to be opened for specific applications. Block specific MAC addresses. Open a virtual server to public. Do not response to ping request with WAN IP address.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Status Local Area Network Wide Area Network - 24 - Current operation and connection status of LAN. Current operation and connection status of WAN.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Troubleshooting General z Check for the appropriate power indication on the LED. If no power, check the adaptor (or External Power Supply) connection between the electrical outlet and the modem. I can’t get good signal. My connection is unstable. z Check for the Signal LED. If off, there is no service coverage. (Out of service area) z Two antennas should be firmly connected to the unit.
CDMA 1xEV-DO Wireless Broadband Modem AXW-D800 / AXW-D1900 Specifications Categories Frequency AXW-D800 Range AXW-D1900 Operation Temperature Operation Humidity AC Adaptor Dimension Weight - 26 - Specifications TX: 824.64~848.37 MHz RX: 859.64~893.37 MHz TX: 1850.00~1909.95 MHz RX: 1930.00~1989.
