SJE10 USER MANUAL
Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Axesstel.
Table of Contents 1. Introduction. …………………………………………....……….. 5 2. Product Overview. ……………………………………...…....… 6 3. Knowing your Smart Jacket. ……………………………..……….. 9 Package Contents. …………………………………...…………...9 Smart Jacket Interface………………………………………………..…9 System Components. ………………………………..…………..10 4. Connecting and Configuring your Smart Jacket …….……….…12 5. Web Manager User Interface. ……………….…………..…... 16 Basic Settings. ………………………………….……….….…… 18 Configuring the Wireless Network Settings………...…..……...
Introduction Thank you for purchasing the Axesstel SJE10 WIFI Smart kit (the Smart Jacket). This user manual will help you setup, configure and outline best practices for maximizing your wireless home network performance with the Smart Jacket. Please be sure to read through this User Manual completely, and pay special attention to the section entitled “Placement of your Smart Jacket for Optimal Performance” on page 2.
• • Jacket itself is positioned vertically, point the antennas as much as possible in an upward direction. In multistory homes, place the Smart Jacket on an upper floor. Try not to place the Smart Jacket near a cordless phone 2. Avoid Obstacles and Interference Avoid placing your Smart Jacket near devices that may emit radio “noise,” such as microwave ovens.
Actual speed depends on the network conditions. ¾ HSUPA Provides up-link performance of up to 5.76Mbit/s. Actual speed depends on the network conditions. Once the connection is established, you can open your browser and connect to any web site that is accessible through the Internet, or access other Internet services (such as email). The connection is “active” when data transmission is occurring.
Solid Yellow Valid connection in WCDMA Blinking Yellow Data transferring in WCDMA Solid Red Valid connection in GPRS Blinking Red Data transferring in GPRS Signal LED Solid Blue Strong signal Blinking Blue (once per blinking) Medium signal Blinking Blue (twice per blinking) Low signal Web-Based Advanced User Interface You can set up the Smart Jacket’s advanced functions easily through web browser, without having to install additional software onto the computer.
Knowing your Smart Jacket Packages Contents • • • • • Smart Jacket main unit User Manual Side Cover Power Supply Battery Smart Jacket Interfaces The Smart Jacket has been designed to be placed on a desktop. The LED indicators are easily visible on the top of the Smart Jacket to provide you with information about network activity and status. 1. Power LED a. Adaptor only OFF Solid Blue Power is OFF Power is ON b. Battery only OFF Solid Blue Blinking Blue Power is OFF Power is ON Battery is low c.
Solid Blue Blinking Blue Wi-Fi network within Modem is activated Active data passed through Wi-Fi 3. Power Jack Connect the included 5V DC power supply to this jack. 4. Rechargeable Battery System components Your Smart Jacket is just one part of a system designed to provide you with a wide range of communication features. Every component of the system is needed to enable these capabilities.
The Smart Jacket The Smart Jacket provides your computer with a connection to the GSM/WCDMA wireless network. Every GSM network operates on one of four radio frequency bands (850MHz, 900MHz and 1800/1900MHz) and WCDMA for three frequency bands(850MHz, 1900MHz and 2100Mhz). The Smart Jacket is available in five configurations: A GSM/WCDMA service provider account Companies that operate GSM/WCDMA networks and provide access to these networks are called service providers.
Connecting and Configuring your Smart Jacket The Smart Jacket has been provisioned at the factory for use with a particular service provider. This sets the Smart Jacket to use particular radio channels and enables services specific for that provider. You will have access to more advance features of the Smart Jacket such as Wi-Fi configuration, and password management. This chapter provides the step-by-step process to access the Smart Jacket. Step 1 │Connect to the Smart Jacket 1.1.
2.5 Open your wireless interface of your PC. Then try to find the SSID”SJE10”. Then, please associate to that SSID. Then you could configure the SJE10 through WEB Browser by enter the http://192.168.1.1 to the browser. Step 3 │ Preparing your PC Your Smart Jacket’s Wireless is configured with DHCP by default. This means that IP address of your PC is automatically assigned by the Smart Jacket.
3.3 Select the “Internet Protocol (TCP/IP)”. Press the “Properties” button. If there is no TCP/IP line listed, you will need to install TCP/IP first. 3.4 Check “Obtain an IP address automatically” 3.5 Check “Obtain DNS address automatically” Server 3.6 Click Ok to exit Properties 3.7 If asked to re-start the PC, click “YES”.
Web Manager User Interface The Web Manager User Interface is a web-based tool that you can use to set up the Smart Jacket if you don’t want to use the default setting of Install CD. You can also use it to manage advanced functions of the Smart Jacket.
Step 2 │Navigate web-based UI 2.1 The Basic Setting page is the first page you will see when you access the web based Advanced User Interface (UI). The basic setting page shows you a quick view of the Smart Jacket’s login setting. All advanced setup pages can be reached from this page. 1. Quick Navigation Links You can go directly to any of the Smart Jacket’s UI pages by clicking directly on these links.
2. Page Name The page you are on can be identified by this name. This User Manual will sometimes refer to pages by name. For instance “Advanced > LAN IP Setup” refers to the “LAN IP Setup” page. Basic Settings Clicking on the header of the “Basic Settings” tab will take you to the “Basic Settings” header page. From this page, the Smart Jacket’s basic settings can be modified.
Configuring the Wireless Network Settings SJE10(Smart Jacket) only Clicking on the header of the “Wireless Settings” tab will take you to the “Wireless Settings” header page. From this page, the Smart Jacket’s Wi-Fi router wireless radio can be enabled or disabled (the default setting is enabled). There are options that allow you to make changes to the Wi-Fi wireless network settings.
Your Smart Jacket can operate in three different wireless modes: “g and b”, “g only”, and “b only”. g and b Mode In this mode, the Smart Jacket is compatible with 802.11b and 802.11g wireless clients simultaneously. This is the factory default mode and ensures successful operation with all Wi-Fi compatible devices. If you have a mix of 802.11b and 802.11g clients in your network, we recommend setting the Smart Jacket to g and b mode.
be changed if needed. If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks. For best performance, use a channel that is at least five channels away from the other wireless network. For instance, if another network is operating on channel 11, then set your network to channel 6 or below. To change the channel, select the channel from the drop-down list. Click “Apply Changes”. The change is immediate.
type this IP address into the address bar of your browser. This address can be changed if needed. 2. Subnet Mask This is a unique, advanced feature of your Axesstel Smart Jacket. It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so. The default setting is “255.255.255.0”. From this page, users can see all settings associated with the Smart Jacket’s router network functions.
Configuring Port Forwarding Clicking on the header of the “Port Forwarding” tab will take you to the “Port Forwarding” header page. This function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network. Since your internal computers are protected by a firewall, computers outside your network (over the Internet) cannot get to them because they cannot be “seen.
quickly. It is recommended that you disable the settings when you are not using a specific application. Block Services The Smart Jacket can be configured to restrict access to the Internet, email, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers. To restrict Internet access to a single computer, for example, enter the IP address of the computer you wish to restrict access to in the IP fields.
¾ Deny. In this mode, the service table shows the client MAC address being blocked by the Smart Jacket. ¾ Allow. In this mode, the service table shows the client MAC address allowed by the Smart Jacket. To modify the service table (i.e. to add, change address or remove clients) simply enter the correct value and click “Apply”. Note: You will not be able to delete the MAC address of the computer you are using to access the Router’s administrative functions (the computer you are using now).
HTTP Ping Blocking To turn OFF the HTTP response, select “Not Respond to HTTP on Internet Port” and click “Apply”. The Smart Jacket will not respond to an HTTP ping. LAN IP Setup Clicking on the header of the “LAN IP Setup” tab will take you to its header page. LAN TCP/IP Setup All settings for the internal LAN setup of the Router can be viewed and changed here. 1. IP Address: The “IP address” is the internal IP address of the Smart Jacket. The default IP address is “192.168.1.1”.
subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so. The default setting is “255.255.255.0”. Use Router as DHCP Server The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network.
Technical Specifications This chapter provides technical product data for the Smart Jacket. Radio frequency and electrical specifications Tri-band UMTS: 2100/ 1900/ 850 MHz (Band I/ II/V) 3.5G Frequency Follow the EU230 Range Quad-band GSM / GPRS / EDGE: 850 / 900 / 1800 / 1900 MHz 3.5G Channel Bandwidth WCDMA 5 MHz WiFi Channel 802.
Appendix A: Glossary HSDPA Provides improved down-link performance of up to 14.4 Mbit/s theoretically. Existing deployments provide up to 7.2 Mbit/s in down-link. Up-link performance is a maximum of 384 kbit/s. Part of 3GPP/UTRAN-FDD Release 5 WCDMA specifications HSUPA Provides improved up-link performance of up to 5.76 Mbit/s theoretically. Standardized as part of 3GPP Release 6. bps bits per second—The actual data speed over the transmission medium.
change than hardware but more permanent than software stored on disk. host 1. A computer that uses a modem or a similar device to answer a calling computer. 2. A source or destination in the communication network. 3. A computer that contains data or files to be accessed by client computers. Also known as a server. IS Interim Standard—After receiving industry consensus, the TIA forwards the standard to ANSI for approval.
system tray Usually located in the lower right corner of your screen TIA Telecommunications Industry Association—A standards-setting trade organization, whose members provide communications and information technology products, systems, distribution services and professional services in the United States and around the world. Consult www.tiaonline.org.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
31