Stealth Reader Stealth Reader Quick Installers Guide Version A.
Stealth Reader Table of Contents Introduction..........................................................................................................3 Specifications ...........................................................................................3 FCC Compliance..................................................................................................4 Pre-Installation ....................................................................................................
Stealth Reader Introduction Specifications Working Environment: The Stealth Reader's operating environment should reside in an area that has the temperature range of -40C to +85C. Also do not submerge the Stealth Reader for more than 30 minutes at a depth of 1 meter. Any longer and the Stealth Reader will receive damage.
Stealth Reader FCC Compliance Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Stealth Reader • • • • • 99% Isopropyl Rubbing Alcohol Cotton Squares (lint free) Plumber's Goop Adhesive #15112 Wire Cutter 9 volt battery In order to install the Stealth Reader without Any chance of water damage these materials are needed: • Devcon Mark 5 epoxy gun for 50ml cartridge • Mixing Nozzle for the Gun #14285 • UY Connectors ◦ 3M IDC Connector-Yellow Part No. 34-7035-9854-9 ◦ 3M IDC Connector-Red Part No. 78-8064-7439-7 ◦ AMP Tel-Splice Connector 2 Wire 19-26 AWG-Part No.
Stealth Reader Installation Installation of the Stealth Reader consists of several different steps. This section goes over the installation of the Stealth Reader and the mounting process with considerations to have in mind. Considerations 1. Signal distance depends on the location of the Stealth Reader's antenna. When the Stealth Reader's antenna is higher the signal is generally stronger. 2. The Pit Lid or Vault may affect the transmission range.
Stealth Reader Mesh Master Metron Neptune Neptune Rockwell Dialog Prolink T-8 AUTO ECR Encoded Encoded Encoded Encoded Encoded 3 Wire Rockwell ECR Encoded 2 Wire Rockwell Touchread Encoded 3 Wire Rockwell Touchread Encoded 2 Wire Schlumberger Schlumberger Schlumberger Sensus ARB V ARB VI AUTO SR II Copyright 2013, Axiometric, LLC Encoded Encoded Encoded Encoded Page 7 Green Green Black Black Red Green Green Green Black Red Brown Red White Green Black Bla
Stealth Reader 3 Wire Sensus SR II Encoded 2 Wire Invensys Neptune Badger Metron AMR System E-coder Absolute Encoder Spectrum 22 AMCO InVision Invensys/Sensus ICE Encoded Encoded Encoded Encoded Encoded Encoded Green Green Black Black Red Red Green Red Black Black Red Red Green Green Black Black Red Black Green Red Black Green Red Red Green Green Black Black Red Red Green Green Black Black Red Green White Red Black Black Red Red Green Green Bl
Stealth Reader wires are connected correctly before filling pods with epoxy. If the wires are hooked up wrong and need to go back and redo them these are the steps to fix the problem. 1. Cut off the wires where they go into the UY gel caps. 2. Repeat procedures 2-4 from the section above. There are some registers that do not connect through wires. Instead they have screws that are next to the indicator that shows which color it would be in the previous chart.
Stealth Reader Mounting When putting a Meter and Register in a certain location it has to be properly mounted. The mounting that will be described in this Manuel will be Pit Mounting. There are other ways to mount compatible with the Stealth Reader, Wall and Pole mounting. Pit Mounting 1. Get the materials for the mounting like in the picture to the right. (Not including Lid) 2.
Stealth Reader Configuration In order to configure the Stealth Reader it has to be fully Installed go to the SMiRF. MIU installations are typically performed in response to an assigned workorder (task). MIUs may also be installed independently by a technician (e.g. for a demonstration or as a repeater to extend range). The installation processes for task assigned and independent installs are very similar. They are described below and the differences are noted.
Stealth Reader It is critical to confirm that this information is correct, especially the MIU ID. When many technicians are working in the same area, it is possible that the SMiRF received a message from a different MIU that was activated by another technician. It is very important to check the Meter Id and MIU ID to ensure the installation is properly recorded. If any of this data is in error, tap “Back” and correct it. When everything is correct tap “Next”.
Stealth Reader Shipping and Handling When sending products to a location, here are guidelines and warnings about shipping and handling the Stealth Reader. • Do NOT ship the Stealth Reader on a Plane or any aircraft. The lithium-ion batteries don't handle the plane ride well and can cause a fire that can't be extinguished by aircraft personal. Trouble Shooting If something hasn't gone the way that was described in this Manuel refer to the proper sections below.