FDK172-834 Open Frame Display PANEL PC User’s Manual
Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
Safety Precautions Before getting started, read the following important cautions. 1. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 2. Disconnect the power cords from the FDK191 Series before making any installation. Be sure both the system and the external devices are turned OFF.
Table of Contents Disclaimers ..................................................................................................... ii Safety Precautions ........................................................................................ iii Chapter 1 Introduction ............................................. 1 1.1 General Description ............................................................................ 1 1.2 Specifications ..................................................................
3.6 Boot Menu.......................................................................................... 50 3.7 Save&Exit........................................................................................... 51 Chapter 4 4.1 System ............................................................................................... 53 4.1.1 4.1.2 4.2 Win 7 ......................................................................................................... 53 Win 8/8.x .............................
This page is intentionally left blank.
FDK172-834 User’s Manual Chapter 1 Introduction This chapter contains general information and detailed specifications of the FDK172-834 series. Chapter 1 includes the following sections: 1.1 General Description Specification Dimensions I/O Outlets Package List General Description The FDK series is an open frame touch panel computer, equipped with a 17-inch TFT LCD ® TM display and low power consumption Intel Atom processor J1900 2.0 GHz.
FDK172-834 User’s Manual 1.2 Specifications Main CPU Board CPU ® Intel Atom TM J1900 2.00GHz processor onboard System Memory One 204-pin DDR3L 1333MHz SO-DIMM socket Maximum memory up to 8GB BIOS America Megatrends BIOS I/O System Standard I/O 2 x RS-232/422/485, 2 x RS232 2 x USB 2.0, 2 x USB 3.0 1 x VGA Ethernet 1 x INTEL I210IT RJ45 for Giga Ethernet Audio 1x Line-out Expansion 2 x Full size Mini-card slot Storage 1 x 2.
FDK172-834 User’s Manual System Specification 17” SXGA(1280x1024) TFT LCD Touch (equip on FDK172-834-R models) 5-wired resistive touch Heat Dispensing Design Disk drive housing One 2.5” SATA drive Net Weight 5.52 Kgs (12.16 lb) Dimension (Main Body Size) 367x 65x 304.
FDK172-834 User’s Manual 1.3 Dimensions and Outlines The following diagrams show the dimensions and outlines of FDK172-834.
FDK172-834 User’s Manual 1.4 I/O Outlets Please refer to the following illustration for I/O locations of the FDK172-834. No Function No Function 1 POWER SWITCH (ATX) 7 COM 2 (RS-232/422/485) 2 1 x 12VDC Power input connector or 24V DC phoenix connector 8 1 X VGA 3 2 X USB 2.0 9 1 X ETHERNET (RJ-45) 4 COM 3 (RS-232) 10 2 X USB 3.
FDK172-834 User’s Manual 1.5 Packing List When you receive the FDK172-834, the bundled package should contain the following items: FDK172-834 unit x 1 Driver CD x1 Power adaptor x 1 (for 12V DC Power Jack type only) Phoenix terminal x 1 (for phoenix type only) If you can not find the package or any items are missing, please contact Axiomtek distributors immediately.
FDK172-834 User’s Manual Chapter 2 Hardware and Installation The FDK172-834 provides rich I/O ports and flexible expansions for you to meet different demand, for example CF card. The chapter will show you how to install the hardware.
FDK172-834 User’s Manual 2.1 Open and close back cover This section tells users how to open and close the back cover. Please follow the steps below. Step 1 Unscrew eleven screws on the back cover. Please refer the photo of top side, right side and left side. Step 2 When users open the back cover, there is a cable connecting between a fan and the motherboard.
FDK172-834 User’s Manual Step 3 Remove the connector first before remove the back cover totally. Step 4 After removing the back cover, users can see the inside of the unit. Step 5 Before closing the back cover, users must connect the fan cable to the motherboard first. Step 6 Then close back cover and fix back the eleven screws.
FDK172-834 User’s Manual 2.2 CF card Installation The FDK172-834 provides one CF slot for users to install CompactFlash™ card. Please refer to the following instructions for installation: Step 1 Turn off the system, and unplug the power cord. Step 2 Locate the CompactFlash 2.3 Serial Ports Interface TM socket, and insert the card into the socket. The FDK172-834 has four serial ports. COM1 and COM2 are RS-232/422/485, while COM3 and COM4 are RS-232.
FDK172-834 User’s Manual 2.3.1 COM port Connector The pin assignment of RS-232/RS-422/RS-485 is listed on the following table.
FDK172-834 User’s Manual 2.4 Ethernet The FDK172-834 is equipped with a high performance Plug and Play Ethernet interface, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
FDK172-834 User’s Manual 2.5 Mountings: Openframe/VESA There are two mounting ways for the FDK172-834 series, openframe and VESA mountings. 2.5.1 Openframe Mount The FDK172-834 series can be mounted into the wall or put on customized front bezel. Please follow the steps below to for the open frame mounting installation. Step 1 Users need to prepare the front bezel/wall, screws, nuts, sponge, and L-type holders by themselves. Step 2 Follow section 1.4 dimensions and drawing below.
FDK172-834 User’s Manual 2.5.2 VESA Mounting FDK172-834 series provides two types of VESA holes, 75mm x 75mm and 100mm x 100mm. These VESA holes can easy for users to install FDK172-834 series via many different types of VESA mounting holders, such as VESA arm, VESA wall holders…etc.
FDK172-834 User’s Manual 2.6 HDD Installation The FDK172-834 provides a convenient Hard Disk Drive (HDD) bracket for users to install 2.5” SATA HDD. Please follow the steps: Step 1 Refer section 2.1 to open the back cover. Step 2 Unscrew 4 screws to take off the HDD bracket. Step 3 Fix the HDD on bracket by 4 screws, and connect SATA cable as well as power cable.
FDK172-834 User’s Manual Step 4 Fix the HDD bracket into the system, and plug the data and power cable to HDD. Installation completes.
FDK172-834 User’s Manual 2.7 DRAM Installation The FDK172-834 provides one 204-pin DDR3 SODIMM socket that support system memory up to 4GB. Please follow steps below to install the memory modules: Step 1 Refer to section 2.1 to open the back cover and find out DIMM socket on mainboard (SBC87832). Step 2 Insert the DRAM to the DIMM socket, and then push it down firmly until it is clipped by the socket. 2 Step 3 1 Installation completes.
FDK172-834 User’s Manual 2.8 Mini cards installation 2.8.1 Wireless LAN card installation The FDK172-834 provides two Mini card slots for user to install wireless LAN cards. You can choose either slot 1 or slot 2 to install the wireless LAN card and refer to the following instructions and illustration: Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot on mainboard. slot1 slot2 Step 2 Insert the wireless LAN card to the slot.
FDK172-834 User’s Manual Step 3 Remove the antenna plug from the top of back cover. Step 4 Install the antenna cable on the back cover. Step 5 Install the antenna on the antenna connector.
FDK172-834 User’s Manual Step 6 2.8.2 Connect the antenna cable to wireless LAN card. mSATA Card Installation The FDK172-834 provides one Mini card slot for user to install mSATA. Please choose the slot 2 when installing the mSATA card and refer to the following instructions and illustration: Step 1 Refer to section 2.1 to open the back cover and find out mini-card slot on mainboard. slot1 slot2 Step 2 20 Insert the mSATA card to the slot 2. Screw it firmly on the slot.
FDK172-834 User’s Manual 2.
FDK172-834 User’s Manual Solder Side 22 Hardware and Installation
FDK172-834 User’s Manual 2.9.1 Jumper Settings Making the proper jumper settings configure the SBC87834 to match the needs of your application. The following table shows the default jumper settings for the onboard devices. ★ Default Setting Jumper JP1 JP2 JP4 JP5 JP6 JP7 JP8 JP11 JP12 JP13 JP14 JP15 Jumper Setting ★ Panel backlight control PWM mode Panel backlight control DC mode Touch Controller 4,8 WIRE ★ Touch Controller 5 WIRE Short 1-2 Short 3-4 ★ LVDS Panel Power : 3.
FDK172-834 User’s Manual 2.9.2 Connectors The connectors allow the CPU Board to connect with other parts of the system. Ensure that all connectors are in place and firmly attached. The following table lists the function of each connector on the SBC87834.
FDK172-834 User’s Manual LVDS connector: CN1 CN1 Pin Assignment Pin Description Pin Description 1 VCC 21 GND 2 VCC 22 GND 3 VCC 23 LVDSA_DATAN0 4 VCC 24 LVDSB_DATAN2 5 VCC 25 LVDSA_DATAP0 6 VCC 26 LVDSB_DATAP2 7 DDC DATA 27 GND 8 DDC CLOCK 28 GND 9 GND 29 LVDSA_DATAN1 10 GND 30 LVDSA_DATAN3 11 LVDSB_DATAN3 31 LVDSA_DATAP1 12 LVDSB_DATAN0 32 LVDSA_DATAP3 13 LVDSB_DATAP3 33 GND 14 LVDSB_DATAP0 34 GND 15 GND 35 LVDSA_DATAN2 16 GND 36 LVDSA_CLK
FDK172-834 User’s Manual LVDS inverter connector: CN2 CN2 Pin Assignment Pin Description Pin Description 1 GND 5 Inverter ON-OFF 2 GND 6 +12V 3 GND 7 +12V 4 Backlight control 8 +12V TOUCH connector: CN3 CN3 Pin Assignment Pin Description 1 X+ 2 X- 3 Y+ 4 Sense 5 X+ 6 X- 7 Y+ 8 Y- 9 GND 26 Hardware and Installation
FDK172-834 User’s Manual HDD power connector: CN4 CN9 Pin Assignment Pin Description 1 +12V 2 GND 3 GND 4 +5V FRONT PANEL pin header: CN6 CN6 Pin Assignment Pin Description Pin Description 1 + 5V 2 Beep 3 GND 4 BUZZER 5 GND 6 Beep 7 NC 8 +5V 9 GND 10 PWBTN 11 GND 12 RESET 13 SATA LED 14 +3.
FDK172-834 User’s Manual SIM card connector: CN7 CN7 Pin Assignment Pin Description Pin Description 1 UIM PWR 5 GND 2 UIM RST 6 UIM VPP 3 UIM CLK 7 UIM DATA 4 NC 8 NC Power connector: CN9 CN9 Pin Assignment Pin Description 1 DCIN (9V -36V) 2 DCIN (9V -36V) 3 GND 4 GND 28 Hardware and Installation
FDK172-834 User’s Manual Digital I/O pin header: CN10 CN10 Pin Assignment Pin Description Pin Description 1 GND 6 GND 2 GPIO0 7 GPIO1 3 GPIO2 8 GPIO3 4 GPIO4 9 GPIO5 5 GPIO6 10 GPIO7 11 GPIO8 12 GPIO9 13 GPIO10 14 GPIO11 15 GPIO12 16 GPIO13 17 GPIO14 18 GPIO15 19 GND 20 GND Speaker Out & MIC IN connector: CN11 CN11 Pin Assignment Pin Description Pin Description 1 SPKOUT_L- 2 SPKOUT_L + 3 SPKOUT_R- 4 SPKOUT_R + 5 MIC IN 6 GND Hardware and Installat
FDK172-834 User’s Manual VGA Cable Connector: CN12 CN12 Pin Assignment Pin Signal Pin Signal 1 Red 2 GND 3 Green 4 N.C. 5 Blue 6 N.C. 7 VCC 8 DDC DATA 9 GND 10 N.C. 11 GND . 12 Horizontal Sync 13 GND 14 Vertical Sync 15 DCC CLK 16 N.C.
FDK172-834 User’s Manual Audio Lin In connector: CN15 CN15 Pin Assignment Pin Description 1 LINE IN L 2 GND 5 LIN IN R Power lamp connector: CN16 CN16 Pin Assignment Pin Description 1 Power (+5V) Pin 2 Description GND Power button connector: CN17 CN17 Pin Assignment Pin Description 1 Power Button Hardware and Installation Pin 2 Description GND 31
FDK172-834 User’s Manual Touch function enable/disable & LED indicator connector: CN18 CN18 Pin Assignment Pin Description 1 ON/OFF button 2 GND 3 LED Panel control Keypad connector: CN19 CN19 Pin Assignment Pin Description 1 GND 2 Panel ON/OFF 3 Abnormal indicate LED 4 Normal indicate LED 5 Blacklight down 6 Blacklight up 32 Hardware and Installation
FDK172-834 User’s Manual USB box header: USB1 USB1 Pin Assignment Pin Description Pin Description 1 +5V 2 +5V 3 USB- 4 USB- 5 USB+ 6 USB+ 7 GND 8 GND 9 GND 10 GND Serial Port box header: COM3, COM4 COM3, COM4 Pin Assignment Pin Description Pin Description 1 DCD 2 DSR 3 RX 4 RTS 5 TX 6 CTS 7 DTR 8 RI 9 GND 10 NC Hardware and Installation 33
FDK172-834 User’s Manual This page is intentionally left blank.
FDK172-834 User’s Manual Chapter 3 AMI BIOS Setup Utility This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility. 3.1 Navigation Keys The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include , , , , , , keys, and so on.
FDK172-834 User’s Manual 3.2 Main Menu System Time/Date Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard. Press the key or the keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.
FDK172-834 User’s Manual 3.3 Advanced Menu The Advanced menu allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: ACPI Settings NCT6106D Super IO Configuration NCT6106D H/W Monitor CPU Configuration IDE Configuration Security Configuration LPSS & SCC Configuration For items marked with “”, please press for more options.
FDK172-834 User’s Manual ACPI Sleep State Allow you to select the Advanced Configuration and Power Interface (ACPI) state to be used for system suspend. Here are the options for your selection, Suspend disable and S3 (Suspend to RAM).
FDK172-834 User’s Manual NCT6106D Super IO Configuration Use this screen to select options for the Super IO Configuration, and change the value of the selected option Serial Port 1-4 configuration Serial port: This option used to enable or disable the serial port. Device Setting: This item specifies the base I/O port address and Interrupt Request address of serial port. The port 0 Optimal setting is 3F8/IRQ4. The port 1 Optimal setting is 2F8/IRQ3.
FDK172-834 User’s Manual Serial type This option used to select RS232/422/485 function.
FDK172-834 User’s Manual NCT6106D H/W Monitor This screen shows the Hardware Health Configuration.
FDK172-834 User’s Manual CPU Configuration This screen shows the CPU Configuration and Intel virtualization technology enable/disable selected 42 AMI BIOS Setup Utility
FDK172-834 User’s Manual IDE Configuration You can use this screen to select options for the SATA Configuration, and change the value of the selected option. SATA Mode Use this item to choose the SATA operation mode. Here are the options for your selection, IDE Mode, AHCI Mode.
FDK172-834 User’s Manual Security Configuration The Advanced menu allows users to update the TXE firmware.
FDK172-834 User’s Manual LPSS & SCC Configuration You can select any of the items in the frame of the screen to change the OS, the default setting is Win 7. Please be informed to select the Windows 8.x when installing Win 8 or Win 8.1. If using the Android OS, please refer to https://01.org/android-ia.
FDK172-834 User’s Manual 3.4 Chipset Menu The Chipset menu allows users to change the advanced chipset settings.
FDK172-834 User’s Manual North Bridge This screen shows the North Bridge memory information.
FDK172-834 User’s Manual USB Configuration You can use this screen to select options for the USB Configuration, If USB3.0 function used, XHCI Mode must enable and EHCI must disable. **XHCI default is Auto.
FDK172-834 User’s Manual 3.
FDK172-834 User’s Manual 3.6 Boot Menu The Boot menu allows users to change boot options of the system. You can select any of the items in the left frame of the screen to go to the sub menus: Setup Prompt Timeout Set the Timeout for wait press key to enter Setup Menu. Bootup NumLock State Use this item to select the power-on state for the NumLock. The default setting is on. Quiet Boot Use this item to enable or disable the Quite Boot state. The default setting is disable.
FDK172-834 User’s Manual 3.
FDK172-834 User’s Manual This page is intentionally left blank.
FDK172-834 User’s Manual Chapter 4 Drivers Installation 4.1 System GOT5152T-834 supports Windows 7, Windows 8/8.1 ,WES 7 and WE8S. To facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing. 4.1.1 Win 7 1. Insert Driver CD and select the “\Drivers”. 2. Select all files and follow the installing procedure. NOTE Please install Microsoft KB2685811 before TXE installation under Windows 7, then installing the drivers.
FDK172-834 User’s Manual 4.1.2 4.2 Win 8/8.x 1. Insert Driver CD and select the “\Drivers”. 2. Select all files and follow the installing procedure. Touch Screen The GOT5152T-834 uses the 5-wire analog resistive. There are the specification and driver installation which are listed below. 4.2.
FDK172-834 User’s Manual 4.2.2 Driver Installation- Windows 7/8.x The GOT5152T-834 provides a touch screen driver that users can install it under the operating system Windows 7/8.x. To facilitate installation of the touch screen driver, you should read the instructions in this chapter carefully before you attempt installation. 1. Insert Driver CD and follow the path to select the “\Drivers\Step 7 - Touch”. 2. Follow the installing procedure and press OK. 3.
FDK172-834 User’s Manual 4. Select the “Standard Calibrate” tab. 5. Calibration: To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration. 6. 56 Press OK.
FDK172-834 User’s Manual 4.3 Embedded O.S. The GOT5152T-834 provides the WES 7 and WE8S Embedded. The O.S. is supported devices which are listed below. 4.3.1 WES 7 & WE8S Here are supported onboard devices: Onboard Multi I/O SATA HDD USB CRT/LCD display 10/100/1000 base-T Ethernet TM CFast or mSATA Onboard Audio Touch Screen PenMount Touch screen Before you can use and calibrate it, here is what you should do: 1.
FDK172-834 User’s Manual This page is intentionally left blank.
FDK172-834 User’s Manual Appendix A Watchdog Timer About Watchdog Timer Software stability is major issue in most application. Some embedded systems are not watched by human for 24 hours. It is usually too slow to wait for someone to reboot when computer hangs. The systems need to be able to reset automatically when things go wrong. The watchdog timer gives us solution. The watchdog timer is a counter that triggers a system reset when it counts down to zero from a preset value.
FDK172-834 User’s Manual WDT Sample Program Enable WDT 1.Enable configuration -O 2E 87 -O 2E 87 2. Select Logic device: -O 2E 07 -O 2F 08 3. WDT Device Enable -O 2E 30 -O 2F 01 4. Set timer unit -O 2E F0 -O 2F 00 (00: Sec; 08: Minute) 5. Set base timer: -O 2E F1 -O 2F 0A Set Reset Time (Ex.0A:10 Sec) Disable WDT 1.Enable configuration -O 2E 87 -O 2E 87 2. Select Logic device: -O 2E 07 -O 2F 08 3.
FDK172-834 User’s Manual Watchdog Timer 61
FDK172-834 User’s Manual 62 Watchdog Timer
FDK172-834 User’s Manual Appendix B Backlight Control About Backlight Control Axiomtek offers the backlight control tool under Windows 7 and Windows 8, people can adjust the panel backlight depending on your personal taste and the amount of ambient light in the room after installing the backlight control tool. How to Use Backlight Control Step 1 According to the OS version, please insert the driver CD and follow the path to select the proper driver, “\Driver\Win8.
FDK172-834 User’s Manual 64 Backlight Control
FDK172-834 User’s Manual Step 2 Follow the installing procedures and press “Close”.
FDK172-834 User’s Manual 66 Backlight Control
FDK172-834 User’s Manual Backlight Control 67
FDK172-834 User’s Manual 68 Backlight Control
FDK172-834 User’s Manual Backlight Control 69
FDK172-834 User’s Manual Step 3 System auto reboot, installation completed. Step 4 Select “△” icon then find out the “Axiomtek” to ensure the brightness driver is installed appropriately. Step 5 How to use the brightness Control There are two ways to adjust the display brightness. Step 5.1 70 Click the “Brightness” to adjust the display brightness with the bar. (For Windows 8.x only.
FDK172-834 User’s Manual Step 5.2. Click the “Control Panel” then select “Power Options” to adjust the display brightness.
FDK172-834 User’s Manual Removed Brightness Control Tool Step 1 72 According to the OS version, please insert the driver CD and follow the path to select the proper driver, “\Driver\Win8.x\Step 8 – Setup” or \Driver\Win7\Step 8 - Setup”.
FDK172-834 User’s Manual Step 2 Follow the procedures and press “Close”.
FDK172-834 User’s Manual 74 Backlight Control
FDK172-834 User’s Manual Step 3 System auto reboot, uninstallation completed.
FDK172-834 User’s Manual This page is intentionally left blank.
