ICO300 Series Robust Din-rail Fanless Embedded System User’s Manual
Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual.
Safety Precautions Before getting started, please read the following important safety precautions. 1. The ICO300 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices.
Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IP40 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5. Type of protection against electric shock: Class I equipment General Cleaning Tips You may need the following precautions before you begin to clean the computer .
Cleaning Tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of item s you may need or want to use while cleaning your computer or computer peripherals. Keep in mind that some components in your computer may only be able to be cleaned using a product designed for cleaning that component, if this is the case it will be mentioned in the cleaning.
Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform your Axiomtek distributor as soon as possible for the suitable solution. For the computers that are no longer useful or no longer working well, please contact your Axiomtek distributor for recycling and we will make the proper arrangement. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd.
Table of Contents Safety Precautions ................................................................................................. iii Classification .......................................................................................................... iv General Cleaning Tips ........................................................................................... iv Scrap Computer Recycling ...................................................................................
APPENDIX A WATCHDOG TIMER ....................................................................... 49 About Watchdog Timer .................................................................................... 49 How to Use Watchdog Timer ...........................................................................
ICO300 Series User’s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the ICO300. The Chapter 1 includes the following sections: General Description System Specification Dimensions I/O Outlets 1.1 General Description ICO300 Din-rail fanless embedded system is suitable for communications control and for protocol converter applications in critical environments.
ICO300 Series User’s Manual Embedded O.S. Supported ® ® ICO300 not only supports W indows 7 and W indows 8, but also supports ® ® embedded OS, such as W indows 7 embedded, W indows 8 embedded and Linux package support. For storage device, ICO300 supports one SATA SSD (or HDD) and one type II CompactFlash ™ socket. 1.2 System Specifications 1.2.1 ® Onboard Intel ATOM™ E3815 (1.46 GHz) processor or E3827 (1.75GHz) processor 1.2.2 CPU BIOS AMI (American Megatrends Inc.
ICO300 Series User’s Manual 1.2.8 USB 2 x USB2.0 USB Pin Define : Pin Signal USB Port 0 Pin Signal USB Port 1 1 2 3 4 VCC DD+ GND 5 6 7 8 VCC DD+ GND 1.2.9 5 6 7 8 1 2 3 4 COM 4 ports DB9 support RS-232/422/485 which can be selected by BIOS. Supports Auto Flow Control in RS485 mode.
ICO300 Series User’s Manual 1.2.11 One DB9 female connector supports 8 bits TTL level programmable digital input/output Pin Signal 1 DIO0 2 DIO1 3 DIO2 4 DIO3 5 DIO4 6 DIO5 7 DIO6 8 DIO7 9 GND 1.2.12 Restore BIOS Optimal Defaults (JP2) Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1 -2. Doing this procedure can restore BIOS optimal defaults . Function Setting Normal (Default) 1-2 close Restore BIOS optimal defaults 2-3 close 1.2.
ICO300 Series User’s Manual 1.2.15 Operation Temperature -20℃ ~ +70℃ -40℃ ~ +70℃ (optional) 1.2.16 -40℃ ~ +85℃ 1.2.17 Weight 1 kg 1.2.19 Humidity 10% ~ 95% (non-condensation) 1.2.18 Storage Temperature Dimensions 48mm(1.88”) (W) x110mm(4.33”) (D) x155mm(6.1”) (H) 1.2.20 System I/O Outlets Four 9-pin D-Sub male connectors, COM1~COM4. One 15-pin D-Sub female connector for VGA. Two 10/100/1000 Base-T RJ-45 with 1.5KV magnetic isolated protection. Two USB 2.
ICO300 Series User’s Manual 1.
ICO300 Series User’s Manual 1.4 I/O Outlets The following figures show you I/O outlets on front view and top view of the ICO300.
ICO300 Series User’s Manual This page is intentionally left blank.
ICO300 Series User’s Manual CHAPTER 2 HARDWARE INSTALLATION The ICO300 is convenient for your various hardware configurations, such as Memory Module and Hard Disk Drive. The chapter 2 will show you how to install the hardware. It includes: 2.1 Installing the Memory Module Step 1 Turn off the system. Step 2 Loosen all screws of the cover and remove the cover from the system. Step 3 Use two fingers to hold the memory module, and insert the gold figure into the slot and push the module down.
ICO300 Series User’s Manual Step 4 The memory module is locked by two latches on the sides. We strongly recommend using “LDC737” silicone on the two sides of the memory for good ability of vibration. Step 5 Put the cover back to the system, and fasten screws tight close the chassis.
ICO300 Series User’s Manual 2.2 Installing the CompactFlash (CF) Step 1 Turn off the system. Step 2 Loosen all screws of the cover and remove the cover from the system. Step 3 Stick CF mylar on CF card. Step 4 Insert the CF card into the socket tightly. Note: Pullout the CF card from the socket when taking out.
ICO300 Series User’s Manual 2.3 Step 1 Installing the Hard Disk Drive Turn off the system. Step 2 Loosen all screws of the cover and remove the cover from the system.
ICO300 Series User’s Manual Step 3 Loosen 4pcs screws of the cover, and put the HDD into the HDD bracket and fix the HDD by 4pcs of screws in the accessory bag. Step 4 Put the HDD bracket on the cover and use 4pcs screws to fix tightly. Takes the SATA+Power HDD cable and Cable Tie out from the accessory bag and connect SATA+Power HDD cable to HDD then use Cable Tie to fix it on the HDD bracket, cut off the lengthy Cable Tie.
ICO300 Series User’s Manual Step 5 Connect SATA+Power HDD cable to the board connector, SATA side first then power side second. Step 6 Put the cover back to the system, and fasten screws tight close the chassis.
ICO300 Series User’s Manual 2.4 Installing Din-rail Mounting The ICO300 provides Din-rail Mount for 2 methods that customers can install as below: Step 1 Prepare Din-rail Mount assembling components (screws and bracket) ready. Step 2 Assembly the bracket to the system and fasten screws tight.
ICO300 Series User’s Manual Method-2 : 16 Hardware Installation
ICO300 Series User’s Manual 2.5 Installing Wall Mounting (optional) The ICO300 provides W all Mounting that customers can install as below: Step 1 Prepare Wall Mount assembling components (screws and bracket) ready. Step 2 Assembly the bracket to the system, and fasten screws tight.
ICO300 Series User’s Manual This page is intentionally left blank.
ICO300 Series User’s Manual CHAPTER 3 AMI UEFI BIOS UTILITY The AMI UEFI BIOS provides users with a built-in Setup program to modify basic system configuration. All configured parameters are stored in a flash-backed-up to save the Setup information whenever the power is turned off . 3.1 Entering Setup To enter the setup screens, follow the steps below: 1. Turn on the computer and press the key immediately. 2. After you press the key, the main BIOS setup menu displays.
ICO300 Series User’s Manual 3.2 The Main Menu Once you enter the AMI BIOS Aptio Setup Utility, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for your selection. Use Select Screen Keys (or Move Keys) to select the Setup Page you intend to configure then press to accept or enter its sub menu. System Date The date format is .
ICO300 Series User’s Manual 3.3 Advanced Features This Advanced section allows users to configure and improve your system, to set up some system features according to your preference.
ICO300 Series User’s Manual Serial Port Configuration The default setting for all Serial Ports are RS232. You can change the setting by selecting the value you want in each COM Port Type. Supports internal 120 ohms terminator in RS422 & RS485 mode. (Please refer below graphics.
ICO300 Series User’s Manual AMI UEFI BIOS Utility 23
ICO300 Series User’s Manual 24 AMI UEFI BIOS Utility
ICO300 Series User’s Manual H/W Monitor Scroll to this item and press to view the monitor hardware status. (Please refer below graphics.
ICO300 Series User’s Manual RTC Wake Settings The default setting is “disable”. If the setting is changed for “enable”, you can set up the fixed time to boot up automatically. (Please refer below graphics.
ICO300 Series User’s Manual AMI UEFI BIOS Utility 27
ICO300 Series User’s Manual 28 AMI UEFI BIOS Utility
ICO300 Series User’s Manual AMI UEFI BIOS Utility 29
ICO300 Series User’s Manual Serial Port Console Redirection Only COM1 has the console redirection function. The default setting for the console redirection function is [ Disabled] (Please refer below graphics.
ICO300 Series User’s Manual If the setting for the console redirection function is changed for [Enabled], the settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or com patible settings.
ICO300 Series User’s Manual And you can further change the setting by selecting or setting the value you want in each function as the following pictures.
ICO300 Series User’s Manual CPU Configuration Scroll to this item and press to view the CPU Configuration informati ons. (Please refer below graphics.
ICO300 Series User’s Manual IDE Configuration Scroll to this item and press to view the IDE Configuration informations. (Please refer below graphics.
ICO300 Series User’s Manual Note: CF and mSATA function can be either one, it can be select by BIOS menu. mSATA and wireless use the same slot, and only one of them can be selected.
ICO300 Series User’s Manual USB Configuration Scroll to this item and press to view the USB Configuration informations. (Please refer below graphics.
ICO300 Series User’s Manual 3.
ICO300 Series User’s Manual 38 AMI UEFI BIOS Utility
ICO300 Series User’s Manual 3.5 Security The default setting for Administrator Password is “Not setting passwords”. The Security menu allows users to change the security settings for the system. You can set the password for both Administrator Password and User Password. (Please refer below graphics.
ICO300 Series User’s Manual Note: The BIOS default has no password, when user created the password, please remember the password number, if users forget password the RMA is the only solution.
ICO300 Series User’s Manual 3.6 Boot Type The default setting boot from onboard LAN PxE Rom is [Disabled] (Please refer below graphics.
ICO300 Series User’s Manual The Boot Option Priorities can select by Boot Option #1, #2… (Please refer below graphics.
ICO300 Series User’s Manual Hard Drive BBS Priorites supports the hard drive boot option.
ICO300 Series User’s Manual 44 AMI UEFI BIOS Utility
ICO300 Series User’s Manual 3.7 Save & Exit This section allows you to determine whether or not to accept your modifications. Type “Y” to quit the setup utility and save all changes. Type “N” to bring you back to the Previous Setup utility. (Please refer below graphics.
ICO300 Series User’s Manual 46 AMI UEFI BIOS Utility
ICO300 Series User’s Manual AMI UEFI BIOS Utility 47
ICO300 Series User’s Manual This page is intentionally left blank.
ICO300 Series User’s Manual APPENDIX A WATCHDOG TIMER About Watchdog Timer After the system stops working for a while, it can be auto-reset by the watchdog timer. The integrated watchdog timer can be set up in the system reset mode by program. How to Use Watchdog Timer The following example enables configuration using debug tool.
ICO300 Series User’s Manual Disable WDT Enable configuration: O 2E 87 ; Un-lock super I/O O 2E 87 Select logic device: O 2E 07 O 2F 08 WDT device disable: O 2E 30 O 2F 00 50 WATCHDOG TIMER
