IFO2225-851 Series 22” TFT Fanless Touch Panel Computer with Intel○R CoreTM 2 Duo Processor User’s Manual
Disclaimers This manual has been carefully checked and believed to contain accurate information. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. AXIOMTEK does not make any commitment to update the information in this manual.
Safety Approvals CE Marking FCC Class A FCC Compliance This equipment has been tested in compliance with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are meant to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications.
Safety Precautions Before getting started, read the following important safety precautions. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. iv The IFO2225-851 Series does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any staticshielded devices.
11. input/out or other connectors shall comply with relevant UL/IEC standard. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: z Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds.
General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. 1. 2. 3. 4. 5. 6. When you need to clean the device, please rub it with a piece of dry cloth. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor. Turn the system off before you start to clean up the component or computer.
z z Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs. Note We strongly recommended that you should shut down the system before you start to clean any single components. Please follow the steps below: 1. Close all application programs 2. Close operating software 3. Turn off power switch 4.
Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform your Axiomtek distributor as soon as possible for the suitable solution. For the computers that are no longer useful or no longer work well, please contact your Axiomtek distributor for recycling and we will make the proper arrangement. Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Table of Contents Disclaimers ..........................................................................ii Safety Approvals.................................................................iii Safety Precautions..............................................................iv Classification ...................................................................... v General Cleaning Tips ........................................................vi Scrap Computer Recycling ...........................................
3.8 Exit Menu.......................................................... 60 CHAPTER 4 DRIVER INSTALLATION ......................... 62 4.1 4.2 4.2.1 4.2.2 x System.............................................................. 62 Touch Screen ................................................... 63 Specification.............................................................. 63 Driver Installation ......................................................
MEMO xi
IFO2225-851 Series User’s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the IFO2225-851 Series. Chapter 1 includes the following sections: 1.1 General Description Features System Specification Dimensions I/O Outlets Package List General Description The IFO2225-851 is an ultra slim panel computer equipped with 22inch 300nits high brightness WSXGA+ LCD display and supports superior Intel○R CoreTM 2 Duo processor up to 2.
IFO2225-851 Series Panel PC User’s Manual 1.2 1.3 Features ¾ 22” ( 300nits) WSXGA+ TFT LCD ¾ Fanless socket P Intel CoreTM 2 Duo or Intel○R Celeron M processor ¾ Spill and dust resistant design (front panel: IP65, whole enclosure: IPX1) ¾ Optional 1 PCI or PCIe x 4 expansion slot ¾ Built-in 1.3 mega pixels camera ¾ Optional wireless (802.
IFO2225-851 Series User’s Manual MAIN SYSTEM CPU Intel ○R Core TM 2 Duo processor up to 2.53 GHz with FSB 667/800/1067MHz CHIPSET INTEL GM/GL45+ICH9M ® SYSTEM MEMORY SUPPORTS 2 DDR3 SODIMM MEMORY UP TO 8 GB 1 x 2.5" SATA HDD DRIVE BAY STORAGE 1 x CompactFlashTM OPTIONAL 1 COMPACT CDOPTICAL DRIVE ROM OR COMBO DRIVE 1 x RS-232/RS-422/RS-485 (COM 1) I/O CONNECTORS 2 x RS-232 (COM 2/3) 4 x USB 2.
IFO2225-851 Series Panel PC User’s Manual OPERATION TEMPERATURE: 0ºC~40ºC (32ºF~104ºF) ENVIRONMENTA RELATIVE HUMIDITY: 10%~95%, NONL CONDESING SHOCK: 10G PEAK ACCELERATION (11 SEC. DURATION) CERTIFICATION CE, FCC classB, EN6060101, UL60601-1 NOTE All specifications and images are subject to change without notice.
IFO2225-851 Series User’s Manual 1.4 Dimensions The following diagrams show you dimensions and outlines of the IFO2225-851 Series.
IFO2225-851 Series Panel PC User’s Manual 1.5 I/O Outlets The following figures show you the locations of the IFO2225-851 Series I/O outlets.
IFO2225-851 Series User’s Manual ¾ I/O Outlets Introduction NO CONNECTOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BRIGHTNESS ADJUST BUTTONS VOLUME ADJUST BUTTONS POWER LED MIC COM 2 (RS-232) COM 1 (RS-232/422/485) ETHERNET X 2 USB 2.0 X 2 Audio (Line-out / Mic-in) VGA Power connector PCI or PCIe slot USB 2.
IFO2225-851 Series Panel PC User’s Manual 1.6 Packing List The package bundled with your IFO2225-851 Series should contain the following items: IFO2225-851 Series Unit x 1 AC-DC Power Adaptor Power Cord x 1 CD x 1 (For Driver and User’s Manual) DVD-combo Cover x 2 (For within DVD-combo) (option) Wall-Mount Bracket x 1 z z z z z z If you can not find this package or any items are missing, please contact AXIOMTEK distributors immediately.
IFO2225-851 Series User’s Manual MEMO Introduction 9
IFO2225-851 Series Panel PC User’s Manual CHAPTER 2 HARDWARE INSTALLATION The IFO2225-851 Series are convenient for your various hardware configurations, such as CPU (Central Processing Unit) and HDD (Hard Disk Drive). The chapter 2 will show you how to install the hardware. It includes: 2.1 DRAM Installation The IFO2225-851 provides socket P and two 204-pin DDR3 SODIMM sockets that support system memory up to 8GB.
IFO2225-851 Series User’s Manual Step 3 Please open the back cover by lifting the joint part as marked. Step 4-1 Open the back cover and find main board and locate the SO-DIMM socket and CPU cooler.
IFO2225-851 Series Panel PC User’s Manual Step 5-1 Release these screws as marked. Step 5-2 Align pins of the CPU with pin holes of the socket. Be careful of the CPU’s orientation that you need to align the arrow mark on the CPU with the arrow key on the socket. Place the CPU into the socket, and use a screwdriver to lock it onto the socket as marked.
IFO2225-851 Series User’s Manual Step 5-3 Place the heat sink on the CPU, and lock it down as marked. Step 6-1 Push down latches on each side of the SO-DIMM socket.
IFO2225-851 Series Panel PC User’s Manual Step 6 Install the memory module into the socket and push it firmly down until it is fully seated. The socket latches are levered upwards and clipped on to the edges of the SO-DIMM.
IFO2225-851 Series User’s Manual 2.2 Hard Disk Drive Installation The IFO2225-851 Series offers a convenient drive bay module for users to install HDD. The system offers users one 2.5” Hard Disk Drive for installation. Please follow the steps: Step 1 Turn off the system, and unplug the Power cord. Step 2 Locate and release these screws to open the back cover.
IFO2225-851 Series Panel PC User’s Manual Step 3 Please open the back cover by lifting the joint part as marked. Step 4 Find the HDD bracket on accessory package and fine HDD socket on main board as marked.
IFO2225-851 Series User’s Manual Step 5 Use assembly parts to fix HDD with the bracket. 1. HDD Bracket x1 2. 2.5 inch Hard-disk 3. Screw x 4 4. Fix four screw holes on the bracket, and assembly the HDD with the bracket. ATTENTION Please follow the direction of Hard-disk installation. “Hard-disk PCB faceup”.
IFO2225-851 Series Panel PC User’s Manual Step 6 Install the HDD bracket inside the system. Plug the HDD in the SATA connector on main board. Step 7 Fix two screw holes on main board as marked.
IFO2225-851 Series User’s Manual Step 8 Close the back cover to the chassis, and fasten all screws.
IFO2225-851 Series Panel PC User’s Manual 2.3 CF Card Installation The IFO2225-851 series provides one CF slot for users to install CompactFlash™ card. Please refer to the following instructions for installation: Step 1 Turn off the system, and unplug the Power cord. Step 2 Locate and release these screws to open the back cover.
IFO2225-851 Series User’s Manual Step 3 Please open the back cover by lifting the joint part as marked. Step 4 Locate the CompactFlash the socket.
IFO2225-851 Series Panel PC User’s Manual Step 5 22 Close the back cover to the chassis, and fasten all screws.
IFO2225-851 Series User’s Manual 2.4 Serial Ports Interface The IFO2225-851 series has three serial ports, COM1 (RS-232/ 422/ 485) and COM2 / COM3 (RS-232).
IFO2225-851 Series Panel PC User’s Manual When COM1 is set to RS-422 or RS-485, the pin assignments are listed below: Pin # 1 2 3 4 5 6 7 8 9 24 Signal Name RS-422 RS-485 TXTX+ RX+ RXNo connector No connector No connector No connector GND DATADATA+ No connector No connector No connector No connector No connector No connector GND Hardware Installation
IFO2225-851 Series User’s Manual 2.5 Wireless Module Installation (Optional) You can follow the steps below to install an optional wireless module. Step 1 Turn off the system, and unplug the Power cord. Step 2 Locate and release these screws to open the back cover.
IFO2225-851 Series Panel PC User’s Manual Step 3 Please open the back cover by lifting the joint part as marked. Step 4 Open the back cover and find main board.
IFO2225-851 Series User’s Manual Step 5 The socket latches are clipped on to the edges of the Mini card. Install wireless LAN card to the socket. ○ 1 ○ 2 Step 6 Find the built-in Antenna cable which is tied with other cables on the bottom of the device. There are two connectors on wireless LAN card. One is MAIN, and the other is AUX. Connect antenna cable to MAIN connector on wireless LAN card.
IFO2225-851 Series Panel PC User’s Manual Step 7 28 Close the back cover to the chassis, and fasten all screws.
IFO2225-851 Series User’s Manual 2.6 Add-on card Installation (Optional) You can follow the steps below to install an optional add-on card. Step 1 Turn off the system, and unplug the Power cord. Step 2 Locate and release these screws to open the back cover.
IFO2225-851 Series Panel PC User’s Manual Step 3 Please open the back cover by lifting the joint part as marked. Step 4 Release the screw as marked. And remove plates.
IFO2225-851 Series User’s Manual Step 5 Insert the add-on card in the socket firmly until it is completely seated.
IFO2225-851 Series Panel PC User’s Manual Step 7 32 Close the back cover to the chassis, and fasten all screws.
IFO2225-851 Series User’s Manual 2.7 Mount There are several mounting ways for the IFO2225-851 Series, Wall mount, VESA and Desktop mountings as below: 2.6.1 Wall mount The mounting for IFO2225-851 Series is Wall mount as below: Step 1 Prepare all parts for installing the wall mount kit. Step 2 Assemble the wall mount kit by using screws to fix the backplane.
IFO2225-851 Series Panel PC User’s Manual 2.6.2 VESA Mount The mounting for IFO2225-851 Series is VESA-Arm as below: Assemble the VESA-Arm by using screws to fix the backplane.
IFO2225-851 Series User’s Manual 2.6.3 Desktop Stand (Optional) The IFO2225-851 Series provides you with an optional Desktop Stand that you can follow the steps below: Step 1 Prepare the parts of desktop stand.
IFO2225-851 Series Panel PC User’s Manual Step 2 Assemble the desktop stand. Fix the screws as marked on the bottom side of chassis. (Use Screw A) Step 3 Assemble the desktop stand by fixing it onto the system. (Use Screw B).
IFO2225-851 Series User’s Manual Step 4 Assembly the hinge cover and fix the screws as marked on the back side of chassis (Use Screw C). Step 4 Fix the desktop stand finish.
IFO2225-851 Series Panel PC User’s Manual Front View 38 Hardware Installation
IFO2225-851 Series User’s Manual MEMO Hardware Installation 39
IFO2225-851 Series Panel PC User’s Manual CHAPTER 3 BIOS SETUP UTILITY This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility. 3.1 Starting To enter the setup screens, follow the steps below: 1. Turn on the computer and press the key immediately. 2. After you press the key, the main BIOS setup menu displays.
IFO2225-851 Series User’s Manual F10 The key allows you to save any changes you have made and exit Setup. Press the key to save your changes. Esc The key allows you to discard any changes you have made and exit the Setup. Press the key to exit the setup without saving your changes. Enter BIOS Setup Utility The key allows you to display or change the setup option listed for a particular setup item. The key can also allow you to display the setup sub- screens.
IFO2225-851 Series Panel PC User’s Manual 3.3 Main Menu When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below. z System Time/Date Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard.
IFO2225-851 Series User’s Manual 3.4 Advanced Menu The Advanced menu allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: y CPU Configuration y IDE Configuration y Super IO Configuration y Hardware Health Configuration y ACPI Configuration y AHCI Configuration y USB Configuration For items marked with “f”, please press for more options.
IFO2225-851 Series Panel PC User’s Manual z CPU Configuration This screen shows the CPU Configuration, 44 BIOS Setup Utility
IFO2225-851 Series User’s Manual z IDE Configuration You can use this item to change options for the IDE Configuration,. The available options appear on the right side of the screen. For items marked with “f”, please press for more options. ¾ SATA#1 Configuration Use this item to control the onboard SATA controller. there are three options for your selection, Compatible, Disabled, and Enhanced. ¾ Configure SATA#1 as Use this item to choose the SATA operation mode.
IFO2225-851 Series Panel PC User’s Manual z Super IO Configuration You can use this item to set up the SuperIO configuration. ¾ 46 Serial Port1 Address This option specifies the base I/O port address and Interrupt Request address of serial port 1. The Optimal setting is 3F8/IRQ4. The Fail-Safe default setting is Disabled.
IFO2225-851 Series User’s Manual ¾ Serial Port2 Address This option specifies the base I/O port address and Interrupt Request address of serial port 2. The Optimal setting is 2F8/IRQ3. The Fail-Safe setting is Disabled. ¾ Serial Port3 Address This option specifies the base I/O port address and Interrupt Request address of serial port 2. The Optimal setting is 3E8/IRQ11. The Fail-Safe setting is Disabled.
IFO2225-851 Series Panel PC User’s Manual z Hardware Health Configuration This item shows the Hardware Health Configuration.
IFO2225-851 Series User’s Manual z ACPI Setting You can use this item to set up ACPI Configuration. ¾ General ACPI Configuration Scroll this item and press to view the General ACPI Configuration sub menu, which contains General ACPI (Advanced Configuration and Power Management Interface) options for your configuration.
IFO2225-851 Series Panel PC User’s Manual z Advanced ACPI Configuration You can use this item to set up advanced ACPI.
IFO2225-851 Series User’s Manual z AHCI Configuration You can use this item to set up AHCI configuration.. ¾ AHCI BIOS Support You can enable or disable this item to control the AHCI function of the SATA controller.
IFO2225-851 Series Panel PC User’s Manual z USB Configuration You can use this item to set up the USB Configuration. ¾ 52 Legacu USB Support Use this item to enable or disable support for USB device on legacy operating system. The default setting is Enabled.
IFO2225-851 Series User’s Manual 3.5 Boot Menu The Boot menu allows users to change boot options of the system. You can select any of the items in the left side of the screen to go to the sub menus: z Boot Settings Configuration For items marked with “f”, please press for more options.
IFO2225-851 Series Panel PC User’s Manual z Boot Settings Configuration 54 ¾ Quick Boot Enabling this item lets the BIOS skip some power on self tests (POST). The default setting is Enabled. ¾ AddOn ROM Display Mode This item selects the display mode for option ROM. The default setting is Force BIOS. ¾ Boot Num-Lock This item selects the power-on state for the NumLock. The default setting is On.
IFO2225-851 Series User’s Manual 3.6 Security Menu The Security menu allows users to change the security settings for the system. ¾ Supervisor Password This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. ¾ User Password This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
IFO2225-851 Series Panel PC User’s Manual ¾ Change User Password Select this option and press to access the sub menu. You can use the sub menu to change the user password. ¾ Boot Sector Virus Protection This option is near the bottom of the Security Setup screen. The default setting is Disabled Disabled Enabled 56 Set this value to prevent the Boot Sector Virus Protection. This is the default setting. Select Enabled to enable boot sector protection.
IFO2225-851 Series User’s Manual 3.7 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left side of the screen to go to the sub menus: y y North Bridge Configuration South Bridge Configuration For items marked with “f”, please press for more options.
IFO2225-851 Series Panel PC User’s Manual z North Bridge Configuration 58 ¾ Memory Hole You can reserve this area of system memory for ISA adapter ROM. When this area is reserved it cannot be cached. Check the user information of peripherals that need to use this area o f system memory for the memory requirements. There are two options, Disabled and 15M16M. ¾ Boot Graphic Adapter Priority This item allows you to select the graphics controller as the primary boot device.
IFO2225-851 Series User’s Manual You can press for the sub-menu to set up video function. z South Bridge Configuration ¾ USB Controller This item allows you to enable or disable USB function/controller. ¾ Restore on AC Power Loss This item controls how the PC will behave once power is restored following a power outage, or other unexpected shutdown.
IFO2225-851 Series Panel PC User’s Manual 3.8 Exit Menu The Exit menu allows users to load your system configuration with optimal or failsafe default values. 60 ¾ Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press . Select Ok to save changes and exit.
IFO2225-851 Series User’s Manual ¾ Discard Changes Use this item to abandon all changes. ¾ Load Optimal Defaults It automatically sets all Setup options to a complete set of default settings when you select this option. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications. In particular, do not use the Optimal Setup options if your computer is experiencing system configuration problems.
IFO2225-851 Series Panel PC User’s Manual CHAPTER 4 DRIVER INSTALLATION 4.1 System IFO2225-851 supports Windows XP/ Windows Vista to facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing. 1. Insert Driver CD in the disk, and select the \IFO2225-851\Driver\.. 2. Please follow folder Step 1 to Step 7 for IFO2225-851 driver installation.
IFO2225-851 Series User’s Manual 4.2 Touch Screen 4.2.1 Specification Touch Screen For 5-wire analog resistive type Touch Screen Controller PenMount 6000 microcontroller Communications USB Resolution 1024 x 1024 Power Input 5V Power Consumption Standby Mode : 13.4mA; Active Mode: 24.
IFO2225-851 Series Panel PC User’s Manual 4.2.2 Driver Installation The IFO2225-851 Series provides a driver of the touch screen that users can install it under operating system Windows XP/ Windows Vista. To facilitate this touch screen driver installation, users should read the instructions in this chapter carefully before start the installation. 1. Insert Driver CD and select the D:\IFO2225-851\Driver\Step6 Touch\Driver\Win2000-XP\setup.exe 2. Follow the installing procedure and press OK. 3.
IFO2225-851 Series User’s Manual 5. Calibration: To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration. 6. Press OK.
