USER MANUAL AXIS Q6042 PTZ Dome Network Camera
About this Document This manual is intended for administrators and users of AXIS Q6042 PTZ Dome Network Camera, and is applicable to firmware 5.55 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be beneficial, for developing shell scripts and applications. Later versions of this document will be posted to the Axis website, as required.
Europe This symbol means that the product shall not be disposed of together with household or commercial waste. Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) is applicable in the European Union member states. To prevent potential harm to human health and the environment, the product must be disposed of in an approved and environmentally safe recycling process.
AXIS Q6042 PTZ Dome Network Camera Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Midspan LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessing the Product . . .
AXIS Q6042 PTZ Dome Network Camera Table of Contents Multi-Connector Cable (sold separately) . . . . . . . . . . . . . . . . . . . . . . . . 57 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Checking the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Q6042 PTZ Dome Network Camera Hardware Overview Hardware Overview 1 2 3 4 5 6 7 1 2 3 4 5 6 7 Part number (P/N) & Serial number (S/N) Network connector (PoE+) Multi-connector SD card slot Status LED indicator Control button Power button Connectors and Buttons For technical specifications, see page 64. Network Connector RJ45 Ethernet connector. Supports Power over Ethernet Plus (PoE+). Use the supplied midspan.
AXIS Q6042 PTZ Dome Network Camera Hardware Overview NOTICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the midspan shall be shielded (STP) and intended for their specific use. Make sure that the midspan is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 .
AXIS Q6042 PTZ Dome Network Camera Hardware Overview Midspan LED Indicators LED Color Indication Port Unlit No camera connected. Green Steady when camera connected, normal operation. Green, flashing Slow flash when overcurrent or short circuit condition on the port. Green, flashing Fast flash when input voltage is out of range or other internal error. Green Steady when AC power input connected.
AXIS Q6042 PTZ Dome Network Camera Accessing the Product Accessing the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems. See Technical Specifications, on page 64. To view streaming video in Internet Explorer, allow installation of AXIS Media Control (AMC) when prompted.
AXIS Q6042 PTZ Dome Network Camera Accessing the Product Access from the Internet Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must configure your network router to allow incoming data traffic to the product. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the product. This is enabled from Setup > System Options > Network > TCP/IP Advanced.
AXIS Q6042 PTZ Dome Network Camera Accessing the Product A temporary certificate (valid for one year) is created, enabling encryption of all traffic to and from the product, and the password can now be set securely. 2. Enter a password and then re-enter it to confirm the spelling. 3. Click OK. The password has now been configured. The Live View Page The controls and layout of the Live View page may have been customized to meet specific installation requirements and user preferences.
AXIS Q6042 PTZ Dome Network Camera Accessing the Product 3. From the Trigger drop-down list, select Input Signal. 4. From the second drop-down list, select Manual Trigger. 5. Select the desired action and configure the other settings as required. For more information about action rules, see . To show the manual trigger buttons in the Live View page: 1. Go to Setup > Live View Layout. 2. Under Action Buttons, select Show manual trigger button.
AXIS Q6042 PTZ Dome Network Camera Accessing the Product PTZ Controls The Live View page also displays Pan/Tilt/Zoom (PTZ) controls. The administrator can enable/disable controls for specified users under System Options > Security > Users. With the PTZ Control Queue enabled the time each user is in control of the PTZ settings is limited. Click the buttons to request or release control of the PTZ controls. The PTZ Control Queue is set up under PTZ > Control Queue.
AXIS Q6042 PTZ Dome Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.
AXIS Q6042 PTZ Dome Network Camera Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS Q6042 PTZ Dome Network Camera Media Streams Note • = IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime adds latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS Q6042 PTZ Dome Network Camera Setting Up the Product Setting Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all settings except System Options See also the online help .
AXIS Q6042 PTZ Dome Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 18. • Stream profiles. See page 19. • Camera settings. See page 20. • Overlay image. See page 21. • Privacy mask. See page 22. • Audio settings. See page 23. • Audio clips. See page 24.
AXIS Q6042 PTZ Dome Network Camera Video and Audio • Video & Audio > Video Stream. Under Preview, click Open and select the Show pixel counter option to enable the rectangle in the image. Use the mouse to move and resize the rectangle, or enter the number of pixels in the Width and Height fields and click Apply. • The Live View page in Internet Explorer in Windows. Right-click in the image and select Pixel counter. Use the mouse to move and resize the rectangle.
AXIS Q6042 PTZ Dome Network Camera Video and Audio • When setting up recording using action rules. See . • When setting up continuous recording. See Continuous Recording, on page 43. • In the Live View page – select the stream profile from the Stream profile drop-down list. For quick setup, use one of the predefined stream profiles. Each predefined profile has a descriptive name, indicating its purpose.
AXIS Q6042 PTZ Dome Network Camera Video and Audio infrared light. The image is shown in black and white when the IR cut filter is off. Set the IR cut filter to Auto to automatically switch between On and Off according to the lighting conditions. Day/Night shift priority - Use the Day/Night shift priority bar to determine when the camera shifts into either day mode or night mode.
AXIS Q6042 PTZ Dome Network Camera Video and Audio 1. Go to Video & Audio > Overlay Image. 2. Click Browse and browse to the file. 3. Click Upload. 4. Select the image to use from the Use overlay image list. 5. Click Save. To display the overlay image: 1. Go to Video & Audio > Video Stream and select the Image tab. 2. Under Overlay Settings, select Include overlay image at the coordinates and enter the X and Y coordinates. 3. Click Save. For information about supported image formats, see the online help .
AXIS Q6042 PTZ Dome Network Camera Video and Audio Since the Pan/Tilt/Zoom coordinates define its size and position, a privacy mask is dynamic in relation to the monitored area. This means that regardless of the angle and zoom of the lens, the same place or object will be hidden. To define at what magnification the mask should be displayed, zoom to the desired level and click Set level. You can add a new mask, re-size the mask with the mouse, choose a color for the mask, and give the mask a name.
AXIS Q6042 PTZ Dome Network Camera Video and Audio • AAC requires a license for both encoding and decoding. AAC is the least complicated and most widely used codec. If achieving the best possible audio quality is a priority, AAC is the recommended codec to use. An AAC license is included in the Axis product. • G711 is an unlicensed standard codec that is useful when integrating audio into a VoIP system • G726 is an unlicensed speech codec that is most commonly used within the security industry.
AXIS Q6042 PTZ Dome Network Camera Live View Config Live View Config You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 19. • Default Viewer for Browser. See page 25. • Viewer Settings. See page 26. • Action Buttons. These are the buttons described in Controls on the Live View Page, on page 11. • User Defined Links. See page 26. • Output Buttons. See page 26.
AXIS Q6042 PTZ Dome Network Camera Live View Config Browser Viewer Description Windows Internet Explorer AMC Recommended viewer in Internet Explorer (H.264/Motion JPEG). QuickTime H.264. Java applet A slower imaging alternative to AMC (Motion JPEG). Requires one of the following installed on the client: • JVM (J2SE) 1.4.2 or higher. • JRE (J2SE) 5.0 or higher. Still image Displays still images only. Click the Refresh button in your browser to view a new image.
AXIS Q6042 PTZ Dome Network Camera Live View Config 2. Under Output Buttons, select the type of control to use: - Pulse activates the output for a defined period of time. The pulse time can be set from 1/100 second to 60 seconds. - Active/Inactive displays two buttons, one or each action. To configure the active and inactive states, go to System Options > Ports & Devices > I/O Ports and set the port’s Normal state. For more information about I/O ports, see I/O Ports, on page 54.
AXIS Q6042 PTZ Dome Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) Preset Positions A preset position is a predefined view that can be used to quickly steer the camera to a specific location. Preset positions can be accessed in several ways: • By selecting the preset from the Preset positions drop-down list in the Live View Page. • When setting up action rules. See . • When setting up Guard Tour. See page 30. • When setting up the Gatekeeper. See page 29 To add a preset position: 1.
AXIS Q6042 PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Gatekeeper The Active Gatekeeper monitors an area such as an entrance gate. When motion is detected in the monitored area, the Gatekeeper will, depending on configuration, steer the camera to a selected preset position or start autotracking from a selected preset position. Using a zoomed-in preset position can make it possible to, for example, read a license plate or identify a person.
AXIS Q6042 PTZ Dome Network Camera PTZ (Pan Tilt Zoom) 2 1 0° 0° B -90° 90° -90° A -180°/180° A 90° -180°/180° B Top view A B Pan limit start Pan limit end Guard Tour A guard tour displays the video stream from different preset positions, one-by-one, in a predetermined order or at random and for configurable time periods. The enabled guard tour will keep running after the user has logged off or closed the browser. The guard tour capability in this Axis product also includes tour recording.
AXIS Q6042 PTZ Dome Network Camera PTZ (Pan Tilt Zoom) 1. Go to PTZ > Guard Tour and click Add. 2. Select Create a record tour and click OK. 3. Enter a descriptive name. 4. Specify the pause length between runs. 5. Click to start recording the Pan/Tilt/Zoom movements. . 6. When satisfied, click 7. Click OK. Note Only the name of the recorded tour and pause between runs can be modified. Starting a new recording will overwrite the existing guard tour.
AXIS Q6042 PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Controls Panel Shortcut Command Buttons can be configured to provide direct access to commands issued via the VAPIX® Application Programming Interface. The buttons will be displayed in the PTZ control panel, which is available in the Live View page through the Ctrl panel button, see page 13. Deselect the options under Enable/Disable controls to disable the pan, tilt, zoom, focus and iris controls.
AXIS Q6042 PTZ Dome Network Camera Detectors Detectors Shock Detection Enable Shock Detection from the Detectors menu. Shock detection is used, for example, to generate an alarm if the product is hit by an object. Use the Shock sensitivity slider to adjust the sensitivity level at which the product should send an alarm upon being hit. Low sensitivity value implies that the product will generate an alarm only if the hit is powerful.
AXIS Q6042 PTZ Dome Network Camera Detectors 3. Adjust the size (drag the bottom right-hand corner) and the position (click on the text at the top and drag to the desired position) of the window. 4. Adjust the Object Size, History and Sensitivity profile sliders (see Motion Detection Parameters for details). Any detected motion within an active window is indicated by red peaks in the Activity window. 5. Click Save.
AXIS Q6042 PTZ Dome Network Camera Detectors Note A multi-connector cable (available from Axis) is required when connecting external audio equipment to the Axis product. See Multi-Connector Cable (sold separately), on page 57. Detected audio is indicated by colored peaks in the Activity indicator. An event is triggered when detected audio rises above or falls below the threshold value, which is represented by the bar.
AXIS Q6042 PTZ Dome Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications Note • It is recommended to run one application at a time.
AXIS Q6042 PTZ Dome Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings.
AXIS Q6042 PTZ Dome Network Camera Events Events The Axis product can be configured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that defines how and when the action is triggered is called an Action Rule. Available Action Rule triggers and conditions include: • Applications — use installed applications to trigger the rule, see Applications, on page 36.
AXIS Q6042 PTZ Dome Network Camera Events - • • Recording — triggers the rule when the Axis product records to the storage device. The recording status trigger can be used to notify the operator, for example by flashing LED lights, if the product has started or stopped to record to the storage device. Note that, this trigger can be used only for edge storage recording status. System - Shock Detected — Trigger the rule when the Axis product detects it has been tilted or hit.
AXIS Q6042 PTZ Dome Network Camera Events 3. Select Detectors from the Trigger drop-down list. 4. Select Motion Detection from the drop-down list. Select the motion detection window to use. 5. Optionally, select a Schedule and Additional conditions, see below. 6. Under Actions, select Record Video from the Type drop-down list. 7. Select a Stream profile and configure the Duration settings as described below. 8. Select Network Share from the Storage drop-down list.
AXIS Q6042 PTZ Dome Network Camera Events 2. A network share can also be used as a storage device for recorded video. Go System Options > Storage to configure a network share before setting up a continuous recording or an action rule to record video. See Storage, on page 53 for more information about storage devices. To add a recipient: 1. Go to Events > Recipients and click Add. 2. Enter a descriptive name. 3. Select a recipient Type. 4. Enter the information needed for the recipient type. 5.
AXIS Q6042 PTZ Dome Network Camera Events Recurrences Recurrences are used to trigger Action Rules repeatedly, for example every 5 minutes or every hour. To set up a recurrence: 1. Go to Events > Recurrences and click Add. 2. Enter a descriptive name and recurrence pattern. 3. Click OK. To use the recurrence in an Action Rule, first select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list.
AXIS Q6042 PTZ Dome Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 43. • To set up action rules, see page 39. • To access recordings, see Recording List, on page 43. • To configure camera controlled storage, see Storage, on page 53. Recording List Recorded videos are listed on the Recordings > List page.
AXIS Q6042 PTZ Dome Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS Q6042 PTZ Dome Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS Q6042 PTZ Dome Network Camera System Options 2. Select an HTTPS certificate from the list of installed certificates. 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups. 5. Click Save to enable the settings. To access the Axis product via the desired protocol, enter https:// or http:// in the address field in a browser. The HTTPS port can be changed on the System Options > Network > TCP/IP > Advanced page.
AXIS Q6042 PTZ Dome Network Camera System Options To install a self-signed certificate: 1. Go to System Options > Security > Certificates. 2. Click Create self-signed certificate and provide the requested information. To create and install a CA-signed certificate: 1. Create a self-signed certificate as described above. 2. Go to System Options > Security > Certificates. 3. Click Create certificate signing request and provide the requested information. 4.
AXIS Q6042 PTZ Dome Network Camera System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled. IPv4 Address Configuration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.
AXIS Q6042 PTZ Dome Network Camera System Options ping -l 408 -t Windows example (this may require that you run the command prompt as an administrator) arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125 4. Check that the network cable is connected and then restart the product by disconnecting and reconnecting power. 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar. 6.
AXIS Q6042 PTZ Dome Network Camera System Options Primary/Secondary DNS server - Enter the IP addresses of the primary and secondary DNS servers. The secondary DNS server is optional and will be used if the primary is unavailable. NTP Configuration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are configured under System Options > Network > TCP/IP > Advanced.
AXIS Q6042 PTZ Dome Network Camera System Options Enable/Disable - When enabled, the Axis product attempts to configure port mapping in a NAT router on your network, using UPnPTM. Note that UPnPTM must be enabled in the product (see System Options > Network > UPnP). Use manually selected NAT router - Select this option to manually select a NAT router and enter the IP address for the router in the field. If no router is specified, the product automatically searches for NAT routers on your network.
AXIS Q6042 PTZ Dome Network Camera System Options Enter the host names or IP addresses and port numbers for the primary and secondary mail servers in the fields provided. A From email address is also required. If the mail server requires authentication, check Use authentication to log in to this server and enter the necessary information. SNMP The Simple Network Management Protocol (SNMP) allows remote management of network devices.
AXIS Q6042 PTZ Dome Network Camera System Options Bonjour The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. Bonjour can be disabled under System Options > Network > Bonjour. Storage SD Card NOTICE To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.
AXIS Q6042 PTZ Dome Network Camera System Options 2. Click Network Share. 3. Enter the IP address, DNS or Bonjour name to the host server in the Host field. 4. Enter the name of the share in the Share field. Sub folders cannot be used. 5. If required, select The share requires login and enter the user name and password. 6. Click Connect. To clear all recordings and data from the Axis product’s folder on the designated share, click Clear under Storage Tools.
AXIS Q6042 PTZ Dome Network Camera System Options For information about firmware upgrade, see Upgrading the Firmware, on page 59. Support Support Overview The System Options > Support > Support Overview page provides information on troubleshooting and contact information, should you require technical assistance. See also Troubleshooting, on page 59. System Overview To get an overview of the Axis product’s status and settings, go to System Options > Support > System Overview.
AXIS Q6042 PTZ Dome Network Camera System Options File Upload Files, for example web pages and images, can be uploaded to the Axis product and used as custom settings. To upload a file, go to System Options > Advanced > File Upload. Uploaded files are accessed through http:///local// where is the selected user group (viewer, operator or administrator) for the uploaded file. Plain Config Plain Config is for advanced users with experience of Axis product configuration.
AXIS Q6042 PTZ Dome Network Camera Multi-Connector Cable (sold separately) Multi-Connector Cable (sold separately) When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller. Connect the multi-connector cable to the product’s multi-connector. To locate the multi-connector, see Hardware Overview, on page 6 .
AXIS Q6042 PTZ Dome Network Camera Multi-Connector Cable (sold separately) 1 3.
AXIS Q6042 PTZ Dome Network Camera Troubleshooting Troubleshooting Checking the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS Q6042 PTZ Dome Network Camera Troubleshooting 1. In UNIX/Linux, type the following from the command line: arp -s temp ping -l 408 In Windows, type the following from a command/DOS prompt (this may require that you run the command prompt as an administrator): arp -s ping -l 408 -t 2. If the product does not reply in 30 seconds, restart it and wait for a reply. Press CTRL+C to stop Ping. 3.
AXIS Q6042 PTZ Dome Network Camera Troubleshooting The IP address has been changed by DHCP IP addresses obtained from a DHCP server are dynamic and may change. If the IP address has been changed, use AXIS IP Utility or AXIS Camera Management to locate the product on the network. Identify the product using its model or serial number, or by the DNS name (if the name has been configured). If required, a static IP address can be assigned manually.
AXIS Q6042 PTZ Dome Network Camera Troubleshooting Lower frame rate than expected See Performance Considerations, on page 66. Reduce the number of applications running on the client computer. Limit the number of simultaneous viewers. Check with the network administrator that there is enough bandwidth available. Check in the AMC Control Panel (H.264 tag) that video processing is NOT set to Decode only key frames. Lower the image resolution.
AXIS Q6042 PTZ Dome Network Camera Troubleshooting Condensation in dome Blurred image Activate fan and heater to remove possible moisture from dome 63
AXIS Q6042 PTZ Dome Network Camera Technical Specifications Technical Specifications Function/group Item Specifications Camera Models AXIS Q6042 60 Hz AXIS Q6042 50 Hz Image sensor ¼” ExView HAD progressive scan CCD Lens f 3.3 – 119 mm F1.4 – 4.2 Autofocus Automatic day/night Horizontal angle of view: 57.2˚ – 1.7˚ Vertical angle of view: 45° – 1.3° Minimum illumination Color: 0.5 lux at 30 IRE F1.4 B/W: 0.008 lux at 30 IRE F1.4 Shutter time 1/30000 s to 0.5 s (60 Hz) 1/30000 s to 1.
AXIS Q6042 PTZ Dome Network Camera Technical Specifications Function/group Item Specifications Network Security Password protection, IP address filtering, HTTPS encryption*, IEEE 802.1X network access control*, digest authentication, user access log *This product includes software developed by the Open SSL Project for use in the Open SSL Toolkit (www.openssl.
AXIS Q6042 PTZ Dome Network Camera Technical Specifications Function/group Item Specifications Operating conditions 0 °C to 50 °C (32 °F to 122 °F) Humidity 10 – 85% RH (non-condensing) Approvals EN 55022 Class A EN 61000-3-2 EN 61000-3-3 EN 61000-6-1 EN 61000-6-2 EN 55024 FCC Part 15 Subpart B Class A ICES-003 Class A VCCI Class A C-tick AS/NZS CISPR 22 Class A KCC KN22 Class A, KN24 IEC/EN/UL 60950-1 IEC/EN 60529 IP52 IEC 60721-4-3 Class 3K3, 3M3 IEC 60068-2 IEC/EN 62262 IK10 Midspan: EN 60950-1, G
AXIS Q6042 PTZ Dome Network Camera Technical Specifications • Heavy network utilization due to poor infrastructure. Bandwidth affected. • Viewing on poorly performing client computers lowers perceived performance. Frame rate affected.
User Manual AXIS Q6042 PTZ Dome Network Camera © Axis Communications AB, 2013 Ver. M2.2 Date: December 2013 Part No.
