AXIS M1065-LW Network Camera User Manual
About this Document This manual is intended for administrators and users of AXIS M1065-LW Network Camera, and is applicable to firmware 6.15 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be useful when developing shell scripts and applications. Later versions of this document will be posted at www.axis.com.
interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. This product complies with FCC radiation exposure limits for an uncontrolled environment. This equipment shall be installed and operated with a minimum distance of 20 cm (7.9 in) between the user and the device. Canada This device complies with Industry Canada licence-exempt RSS standard(s).
223 69 Lund Sweden Tel: +46 46 272 18 00 Fax: +46 46 13 61 30 www.axis.com Support Should you require any technical assistance, please contact your Axis reseller. If your questions cannot be answered immediately, your reseller will forward your queries through the appropriate channels to ensure a rapid response. If you are connected to the Internet, you can: • download user documentation and software updates • find answers to resolved problems in the FAQ database.
AXIS M1065-LW Network Camera Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . . . . . .
AXIS M1065-LW Network Camera Table of Contents Continuous Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS M1065-LW Network Camera Safety Information Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE TICE NO Indicates a situation which, if not avoided, could result in damage to property.
AXIS M1065-LW Network Camera Hardware Overview Hardware Overview For specifications of the hardware components, see Technical Specifications on page 71. 1 2 3 4 5 6 7 8 9 10 11 Focus lock ring Focus ring IR LED PIR sensor Speaker Status LED Control button WLAN pairing button Network connector SD card slot Power connector Connectors and Buttons Network Connector RJ45 Ethernet connector. NOTICE TICE NO The product shall be connected using a shielded network cable (STP).
AXIS M1065-LW Network Camera Hardware Overview SD card slot NOTICE TICE NO • Risk of damage to SD card. Do not use sharp tools, metal objects or excessive force when inserting or removing the SD card. Use your fingers to insert and remove the card. • Risk of data loss and corrupted recordings. Do not remove the SD card while the product is running. Disconnect power or unmount the SD card from the Axis product’s webpages before removal. This product supports microSD/microSDHC/microSDXC cards (not included).
AXIS M1065-LW Network Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. We recommend the following browsers: • Internet Explorer® with Windows® • Safari® with OS X® • ChromeTM or Firefox® with other operating systems. To view streaming video in Internet Explorer, allow installation of AXIS Media Control (AMC) when prompted. The Axis product includes one (1) H.
AXIS M1065-LW Network Camera Access the Product Set the Root Password To access the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which opens when the product is accessed for the first time. To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate.
AXIS M1065-LW Network Camera Access the Product Click Snapshot to save a snapshot of the video image. This button is primarily intended for use when the AXIS Media Control viewer toolbar is not available. Enable this button from Live View Config > Action Buttons. The Audio clip drop-down list allows you to play an audio clip from the Live View page. Select the audio clip and click the Play button. Activate or de-activate IR illumination from Setup > Video & Audio > Camera Settings.
AXIS M1065-LW Network Camera Access the Product For information about how to configure audio, see Set Up Audio on page 25. Speaker button — Click to turn the speakers on or off. Microphone button – Click to mute or unmute the microphone. In Simplex - speaker only mode, the Microphone and Talk buttons must both be active to send audio to the Axis product. Click either button to stop audio transmission. Use the slider to control the volume of the speakers and the microphone.
AXIS M1065-LW Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.264 H.
AXIS M1065-LW Network Camera Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start screen or Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS M1065-LW Network Camera Media Streams Note • = IP address • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS M1065-LW Network Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have restricted access to settings, see Users on page 50 See also the online help .
AXIS M1065-LW Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 18. • Stream profiles. See page 20. • Camera settings. See page 21. • View area. See page 23. • Overlay image. See page 23. • Privacy mask. See page 25. • Audio settings. See page 25. • Audio clips. See page 26.
AXIS M1065-LW Network Camera Video and Audio • Rotate image. If required, the image can be rotated. • Color setting. Select either Color or Black & White. Black & White uses less bandwidth than Color. • Maximum frame rate. To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a fixed amount. Alternatively, the frame rate can be set as Unlimited, which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay settings.
AXIS M1065-LW Network Camera Video and Audio How to set an H.264 profile 1. To change the settings for all H.264 streams that do not use a stream profile, go to Video & Audio > Video Stream > H.264. 2. To increase or decrease the number of frames per GOP, set the GOP length. 3. Select one of the H.264 profiles. 4. Select on of the following: - Variable bit rate - Maximum bit rate 5. If you select Maximum bit rate, select which variable to prioritize in the Priority drop-down list. 6. Click Save.
AXIS M1065-LW Network Camera Video and Audio Camera Settings The Video & Audio > Camera Settings page provides access to advanced image settings for the Axis product. Image Appearance To change Image Appearance go to the menus under Setup > Video & Audio > Camera Settings. Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation and the value 0 gives minimum color saturation.
AXIS M1065-LW Network Camera Video and Audio Shutter speed is related to the amount of time the shutter is opened and is measured in seconds (s). A slow shutter speed allows more light to reach the sensor and can help produce a brighter image in low light situations. On the other hand, a slow shutter speed can cause moving objects to appear blurry. Set Wide Dynamic Range to WDR Off and set Shutter to • Auto to set the shutter speed automatically.
AXIS M1065-LW Network Camera Video and Audio The IR illumination can be activated or de-activated, and its intensity can be increased or decreased by moving the slider, from the product’s Live View page. Other settings can be defined from Setup > Video & Audio > Camera Settings. De-select the Enable IR illumination option to disable IR illumination altogether. If you disable the Synchronize IR illumination with day/night option, IR illumination will not be synchronized with day/night changes.
AXIS M1065-LW Network Camera Video and Audio 2. To include date and time, select Include date and Include time. 3. To include a text string, select Include text and enter the text in the field. Modifiers can be used, see File Naming & Date/Time Formats in the online help . 4. Select size, color, and placement of the text string. 5. Click Save. To modify the date and time format, go to System Options > Date & Time. See Date & Time on page 52. How to include overlay text in an action rule 1.
AXIS M1065-LW Network Camera Video and Audio For more examples of hexadecimal values, see the online help - . To scale the image automatically, select Scale with resolution. The image will be scaled down to fit the resolution used by the Axis product. 5. Click Save. How to include an overlay image 1. Go to Video & Audio > Overlay Image. 2. Select the image to use from the Use overlay image list and click Save. 3. Go to Video & Audio > Video Stream and select the Image tab. 4.
AXIS M1065-LW Network Camera Video and Audio Audio Input Configure the audio input settings under Audio> Audio Settings. Source lists the built-in microphone. Use the Input gain to control the volume (dB Full Scale) of the audio input. If the sound is too low, choose a higher dB, to amplify the sound. If the sound is too high, choose a lower dB. The Level bar gives a visual representation of the audio signal level in dB relative to the full-scale input level. • Green – the signal is at a good level.
AXIS M1065-LW Network Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 20. • Default Viewer for Browser. See page 27. • Viewer Settings. See page 27. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 11 . • User Defined Links. See page 28.
AXIS M1065-LW Network Camera Configure the Live View Page User Defined Links To display user-defined links in the Live View page, select the Show custom link option, give the link a name and then enter the URL to link to. When defining a web link do not remove the 'http://' from the URL address. Custom links can be used to run scripts or activate external devices connected to the product, or they can link to a web page.
AXIS M1065-LW Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) PTZ (pan, tilt and zoom) is available if you have enabled digital PTZ in the selected view area. For more information on view areas, see View Area on page 23. About preset positions A preset position is a saved view that can be used to quickly steer the camera to a specific position.
AXIS M1065-LW Network Camera PTZ (Pan Tilt Zoom) The Panel Shortcut Command Buttons list shows the user-defined buttons that can be accessed from the Live View page’s Ctrl panel. These buttons can be used to provide direct access to commands issued using the VAPIX® application programming interface. Click Add to add a new shortcut command button.
AXIS M1065-LW Network Camera Detectors Detectors About camera tampering Camera Tampering can generate an alarm when the camera is repositioned, or when the lens is covered, spray-painted or severely de-focused. To send an alarm, for example via email, an action rule must be set up. How to configure tampering detection 1. Go to Detectors > Camera Tampering. 2. Set the Minimum duration, that is the time that must elapse before an alarm is generated.
AXIS M1065-LW Network Camera Detectors Once motion detection windows are configured, the Axis product can be configured to perform actions when motion is detected. Possible actions include uploading images and start recording. For more information, see Set Up Action Rules on page 42. Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera.
AXIS M1065-LW Network Camera Detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window, and select a low object size. • To avoid triggering on small objects, select a high object size. • While monitoring an area where moving objects are not expected, select a high history level. This will cause motion detection to trigger as long as the object is present in the window. • To only detect flashing light, select a low sensitivity.
AXIS M1065-LW Network Camera Applications Applications AXIS Camera Application Platform (ACAP) is an open platform that enables third parties to develop analytics and other applications for Axis products. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications Note • Several applications can run at the same time but some applications might not be compatible with each other.
AXIS M1065-LW Network Camera Applications If the Axis product is reset to factory default, uploaded applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings on page 65.
AXIS M1065-LW Network Camera AXIS Video Motion Detection AXIS Video Motion Detection AXIS Video Motion Detection is an application that detects moving objects in the camera’s field of view. When a moving object is detected, AXIS Video Motion Detection sends an alarm that can be used by the Axis product or by third-party software to for example, record video or send a notification. AXIS Video Motion Detection 3 is included with the Axis product and is available under Setup > Applications.
AXIS M1065-LW Network Camera AXIS Video Motion Detection 7. If too many unwanted objects are tracked, enable and configure one or more of the ignore filters. See Ignore Filters on page 38. After modifying a setting, click Save to apply the changes. The video stream will be restarted and it may take a few seconds before the change is applied. Include Area The include area is the area in which moving objects will be detected. Objects moving outside the include area will be ignored.
AXIS M1065-LW Network Camera AXIS Video Motion Detection To highlight the exclude areas, click on the icon. Visual Confirmation Visual confirmation is used to validate that the settings are correct, that is, that all objects that should be detected are detected. Visual confirmation is used to validate that the settings are correct, that is, that all objects that should be tracked are tracked. Note To use visual confirmation, Internet Explorer and AXIS Media Control (AMC) must be used.
AXIS M1065-LW Network Camera AXIS Video Motion Detection ponds or large trees, use exclude areas instead of the filter. The filter will be applied to all moving objects in scene and, if set to a value too large, important objects might not be detected. The swaying object filter is used to avoid tracking objects that only move a short distance, for example moving trees, flags and their shadows. Use the filter if such objects cause a lot of unwanted tracked objects.
AXIS M1065-LW Network Camera AXIS Video Motion Detection 1. Select the Short-lived objects option. 2. Enter the number of seconds in the field. The number of seconds is the minimum time that must pass before the object is detected. Start with a small number. 3. Enter the number of seconds in the field. The number of seconds is the minimum time that must pass before tracking starts. Start with a small number. 4. Click Save to apply the filter. 5. Use visual confirmation to verify the settings. 6.
AXIS M1065-LW Network Camera AXIS Video Motion Detection 1. Insert an SD card in the Axis product, or go to Setup > System Options > Storage in the Axis product’s webpages and configure the product to use a network share. 2. Optionally, go to Setup > Video & Audio > Stream Profiles and create a stream profile to use for recording. 3. Go to Setup > Events > Action Rules and click Add to create a new action rule. 4. From the Trigger drop-down list, select Applications and then select VMD 3DigitalAutoTracking.
AXIS M1065-LW Network Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS M1065-LW Network Camera Events • • • • - Virtual Inputs – can be used by a VMS (Video Management System) to trigger actions. Virtual inputs can, for example, be connected to buttons in the VMS user interface. - Moving – Trigger the rule when the camera view moves due to a PTZ operation. This can for example be used as an additional condition to prevent an action rule triggered by motion detection to record video while the camera view moves due to a PTZ operation.
AXIS M1065-LW Network Camera Events • Status LED – Flash the LED indicator. This can for example be used to validate triggers such as motion detection during product installation and configuration. • WDR Mode – The WDR Mode can be turned on or off when the action rule is triggered. Add Recipients The product can send media files and messages to notify users about events. Before the product can send media files or notification messages, you must define one ore more recipients.
AXIS M1065-LW Network Camera Events Network Share A network share can also be used as a storage device for recorded video. Go System Options > Storage to configure a network share before setting up a continuous recording or an action rule to record video. For more information about storage devices, see Storage on page 61.
AXIS M1065-LW Network Camera Events 3. Click OK. To use the recurrence in an action rule, first select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list. To modify or remove recurrences, select the recurrence in the Recurrences List and click Modify or Remove.
AXIS M1065-LW Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 48. • To set up action rules, see page 42. • To access recordings, see Find Recordings on page 47. • To play recordings, see Play Recording on page 47. • To export a recording as a video clip, see Export Video Clip on page 48. • To configure camera controlled storage, see Storage on page 61.
AXIS M1065-LW Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List. 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the filters. See also Find Recordings on page 47. 3. Select the recording and click Play. The recording will be played in a new browser window. Export Video Clip Recordings on the SD card or network share can be exported as video clips.
AXIS M1065-LW Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS M1065-LW Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS M1065-LW Network Camera System Options HTTPS HTTPS (HyperText Transfer Protocol over Secure Socket Layer, or HTTP over SSL) is a web protocol providing encrypted browsing. HTTPS can also be used by users and clients to verify that the correct device is being accessed. The security level provided by HTTPS is considered adequate for most commercial exchanges. The Axis product can be configured to require HTTPS when users from different user groups (administrator, operator, viewer) log in.
AXIS M1065-LW Network Camera System Options About certificates Certificates are used to authenticate devices on a network. Typical applications include encrypted web browsing (HTTPS), network protection via IEEE 802.1X and secure upload of images and notification messages for example via email. Two types of certificates can be used with the Axis product: Server/Client certificates - To authenticate the Axis product. A Server/Client certificate can be self-signed or issued by a Certificate Authority (CA).
AXIS M1065-LW Network Camera System Options • Synchronize with NTP Server – Obtains date and time from an NTP server. With this option, date and time settings are updated continuously. For information on NTP settings, see NTP Configuration on page 55. If using a host name for the NTP server, a DNS server must be configured. See DNS Configuration on page 55. • Set manually – Allows you to manually set date and time. If using an NTP server, select your Time zone from the drop-down list.
AXIS M1065-LW Network Camera System Options Assign IP Address Using ARP/Ping The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power. 1. Acquire a free static IP address on the same network segment as the computer. 2. Locate the serial number (S/N) on the product label. 3. Open a command prompt and enter the following commands: Linux/Unix syntax arp -s temp ping -s 408 Linux/Unix example arp -s 192.
AXIS M1065-LW Network Camera System Options AXIS Internet Dynamic DNS Service AXIS Internet Dynamic DNS Service assigns a host name for easy access to the product. For more information, see www.axiscam.net To register the Axis product with AXIS Internet Dynamic DNS Service, go to System Options > Network > TCP/IP > Basic. Under Services, click the AXIS Internet Dynamic DNS Service Settings button (requires access to the Internet).
AXIS M1065-LW Network Camera System Options HTTP The HTTP port used by the Axis product can be changed under System Options > Network > TCP/IP > Advanced. In addition to the default setting, which is 80, any port in the range 1024–65535 can be used. HTTPS The HTTPS port used by the Axis product can be changed under System Options > Network > TCP/IP > Advanced. In addition to the default setting, which is 443, any port in the range 1024–65535 can be used.
AXIS M1065-LW Network Camera System Options Note H.264 video streams will not be available if the RTSP server is disabled. Wireless Status of wireless networks To view a list of available wireless networks, go to System Options > Network > Wireless. The status of wireless networks list is the result of a network scan and provides the following information: • SSID is the name of a wireless network. • Mode shows the type of network, for example Master (an access point).
AXIS M1065-LW Network Camera System Options Note SSID is sometimes written as ESSID. Select the network Security method. All settings must match the settings in the access point. The following security methods are supported, where WPATM-/WPA2TM-Enterprise is more secure than WPA-/WPA2-PSK, which in turn is more secure than WEP: • WPA-/WPA2–PSK. See page 58. • WPA-/WPA2-Enterprise. See page 58. • No security (not recommended). See page 60. If applicable, select the Network type.
AXIS M1065-LW Network Camera System Options Important To ensure successful certificate validation, time synchronization should be performed on all clients and servers prior to configuration. How to configure the wireless settings using WPATM-/WPA2-Enterprise and EAP-TLS 1. Go to System Options > Security > Wireless. 2. In the SSID field, type the name of the wireless network. 3. Under Security, select WPA-/WPA2–Enterprise. 4. Under WPA-Enterprise type, select EAP-TLS. 5.
AXIS M1065-LW Network Camera System Options No Security The No security option provides no protection against attacks. It is not a recommended method and should only be used during short periods and exceptional cases. To configure the wireless settings with no security: 1. Select the network type being used by the access point, Master. 2. Click Save. SOCKS SOCKS is a networking proxy protocol.
AXIS M1065-LW Network Camera System Options Note All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps. SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required. To use SNMP v3, HTTPS must be enabled, see HTTPS on page 51. To enable SNMP v3, check the box and provide the initial user password. Note The initial password can only be set once.
AXIS M1065-LW Network Camera System Options The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management. If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card. To avoid filling the card, it is recommended to remove recordings continuously.
AXIS M1065-LW Network Camera System Options 5. Click OK to start formatting the card. Encrypt SD Card Data To prevent unauthorized individuals and systems from accessing recorded video, the SD card content can be encrypted. Encryption can only be enabled when the card is unmounted. After enabling encryption, the SD card must be formatted so that no unencrypted data remains on the card. The card must also be mounted before it can be used.
AXIS M1065-LW Network Camera System Options To stop writing to the share and protect recordings from being removed, select Lock under Recording Settings. Maintenance The Axis product provides several maintenance functions. These are available under System Options > Maintenance. Click Restart to perform a correct restart if the Axis product is not behaving as expected. This will not affect any of the current settings. Note A restart clears all entries in the Server Report.
AXIS M1065-LW Network Camera System Options Access Log - Lists all failed attempts to access the product. The Access Log can also be configured to list all connections to the product (see below). Server Report - Provides information about the product status in a pop-up window. The Access Log is automatically included in the Server Report. You can view or download the server report. Downloading the server report creates a .zip file that contains a complete server report text file in UTF–8 format.
AXIS M1065-LW Network Camera System Options To reset the product to the factory default settings: 1. Disconnect power from the product. 2. Press and hold the control button and reconnect power. See Hardware Overview on page 8 . 3. Keep the control button pressed for 15–30 seconds until the status LED indicator flashes amber. 4. Release the control button. The process is complete when the status LED indicator turns green. The product has been reset to the factory default settings.
AXIS M1065-LW Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS M1065-LW Network Camera Troubleshooting 3. Open a browser and type in the product’s IP address. In the page that opens, use the Browse button to select the upgrade file to use. Then click Load to restart the upgrade process. 4. After the upgrade is complete (1–10 minutes), the product automatically restarts and shows a steady green on the Status indicator. 5. Reinstall the product, referring to the Installation Guide.
AXIS M1065-LW Network Camera Troubleshooting The product is accessible locally but not externally Router configuration To configure your router to allow incoming data traffic to the Axis product, enable the NAT-traversal feature which will attempt to automatically configure the router to allow access to the Axis product, see NAT traversal (port mapping) for IPv4 on page 56. The router must support UPnPTM. Firewall protection Check the Internet firewall with your network administrator.
AXIS M1065-LW Network Camera Troubleshooting No audio Incorrect setup Check the sound card in the computer. Ensure that mute is not selected and that the volume settings are correct. Check that Enable audio support is selected under Setup > System Options > Security > Audio Support. Check that the correct Audio Input source is selected under Setup > Video & Audio > Audio Settings. Poor audio quality Stuttering Reduce the number of listeners and viewers. Decrease image resolution and compression.
AXIS M1065-LW Network Camera Technical Specifications Technical Specifications You can find the latest version of the technical specifications at www.axis.com Camera Image sensor 1/3" progressive scan RGB CMOS Lens Fixed focal length, 2.8 mm, F2.0 Horizontal field of view: 110° Vertical field of view: 61° M12 mount, fixed iris, IR corrected Day and night Automatically removable IR cut filter Minimum illumination Color: 0.25 lux at 50 IRE F2.0 B/W: 0.05 lux at 50 IRE F2.
AXIS M1065-LW Network Camera Technical Specifications Application Open API for software integration, including VAPIX® and AXIS Camera Application Platform; specifications Programming at www.axis.com Interface AXIS Video Hosting System (AVHS) with One-Click Connection ONVIF Profile S; specifications at www.onvif.org Analytics AXIS Video Motion Detection 3, Audio detection Support for AXIS Camera Application Platform, AXIS Cross Line Detection, AXIS Digital Autotracking and third-party applications, see www.
AXIS M1065-LW Network Camera Technical Specifications General Casing Polycarbonate, Aluminium, recycled plastic Color: White NCS S 1002-B For repainting instructions of skin cover or casing and impact on warranty, contact your Axis partner. Sustainability PVC free, 64% recycled plastic Memory 512 MB RAM, 256 MB Flash Power 4.75–5.25 V DC, typical 2.7 W, max 5.0 W IR illumination IR illumination, LED with adjustable intensity.
AXIS M1065-LW Network Camera Technical Specifications Performance Considerations When setting up your system, it is important to consider how various settings and situations will affect performance. Some factors affect the amount of bandwidth (the bit rate) required, others can affect the frame rate, and some affect both. If the load on the CPU reaches its maximum, this will also affect the frame rate.
User Manual AXIS M1065-LW Network Camera © Axis Communications AB, 2016 Ver. M1.18 Date: August 2016 Part No.
