AXIS M1045-LW Network Camera User Manual
About this Document This manual is intended for administrators and users of AXIS M1045-LW Network Camera, and is applicable to firmware 6.15 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be useful when developing shell scripts and applications. Later versions of this document will be posted at www.axis.com.
Korea 이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에 서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. 적절히 접지된 STP (shielded twisted pair) 케이 블을 사용하여 제품을 연결 하십시오. Radio transmission This equipment may generate or use radio frequency energy. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. USA This device complies with Part 15 of the FCC Rules.
will appear in the product’s server report. For more information about the server report, see the product´s setup pages or contact Axis support. The battery should not be replaced unless required, but if the battery does need replacing, contact Axis support at www.axis.com/techsup for assistance. Lithium coin cell 3.0 V batteries contain 1,2-dimethoxyethane; ethylene glycol dimethyl ether (EGDME), CAS no. 110-71-4. WARNING • Risk of explosion if the battery is incorrectly replaced.
AXIS M1045-LW Network Camera Table of Contents Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hazard levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other message levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . . . . .
AXIS M1045-LW Network Camera Table of Contents Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS M1045-LW Network Camera Safety information Safety information Hazard levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE TICE NO Indicates a situation which, if not avoided, could result in damage to property.
AXIS M1045-LW Network Camera Hardware overview Hardware overview For specifications of the hardware components, see Technical specifications on page 68. 1 2 3 4 5 6 7 8 9 Focus lock ring Focus ring IR LED Status LED Control button WLAN pairing button Network connector SD card slot Power connector Connectors and Buttons Network connector RJ45 Ethernet connector. NOTICE TICE NO The product shall be connected using a shielded network cable (STP).
AXIS M1045-LW Network Camera Hardware overview SD card slot NOTICE TICE NO • Risk of damage to SD card. Do not use sharp tools, metal objects or excessive force when inserting or removing the SD card. Use your fingers to insert and remove the card. • Risk of data loss and corrupted recordings. Do not remove the SD card while the product is running. Disconnect power or unmount the SD card from the Axis product’s webpages before removal. This product supports microSD/microSDHC/microSDXC cards (not included).
AXIS M1045-LW Network Camera How to access the product How to access the product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. We recommend the following browsers: • Internet Explorer® with Windows® • Safari® with OS X® • ChromeTM or Firefox® with other operating systems. To view streaming video in Internet Explorer, allow installation of AXIS Media Control (AMC) when prompted.
AXIS M1045-LW Network Camera How to access the product How to set the root password To access the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which opens when the product is accessed for the first time. To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate.
AXIS M1045-LW Network Camera How to access the product Click Snapshot to save a snapshot of the video image. This button is primarily intended for use when the AXIS Media Control viewer toolbar is not available. Enable this button from Live View Config > Action Buttons. Activate or de-activate IR illumination from Setup > Video > Camera Settings. Enable this button from Live View Config > Action Buttons. Move the slider to increase or decrease the intensity of the IR illumination.
AXIS M1045-LW Network Camera How to access the product Click the Emulate joystick mode button and click in the image to move the camera view in the direction of the mouse pointer. Click the Center mode button and click in the image to center the camera view on that position. The center mode button could also be used to zoom in on a specific area. Click in the image and drag to draw a rectangle surrounding the area to be magnified. To zoom out, rotate the mouse wheel.
AXIS M1045-LW Network Camera About media streams About media streams The Axis product provides several video stream formats. Your requirements and the properties of your network will determine the type you use. The live view window in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream profiles. Other applications and clients can access video streams directly, without going via the live view window. About H.264 format H.
AXIS M1045-LW Network Camera About media streams The AMC Control Panel can be used to configure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start screen or Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS M1045-LW Network Camera About media streams Note • = IP address • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS M1045-LW Network Camera How to set up the product How to set up the product The Axis product can be configured by users with administrator or operator rights. To open the product’s setup pages, click Setup in the top right-hand corner of the live view window. • Administrators have unrestricted access to all settings. • Operators have restricted access to settings, see Users on page 48 See also the online help .
AXIS M1045-LW Network Camera About video settings About video settings It is possible to configure the following video features in your Axis product: • Video stream. See page 18. • Stream profiles. See page 20. • Camera settings. See page 20. • View area. See page 23. • Overlay image. See page 23. • Privacy mask. See page 25. How to set up video streams To set up the product’s video streams, go to Video > Video Stream. The video stream settings are divided into the following tabs: • Image.
AXIS M1045-LW Network Camera About video settings • Maximum frame rate. To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a fixed amount. Alternatively, the frame rate can be set as Unlimited, which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay settings. See About overlay text on page 23. Click Save to apply the new settings. About H.264 H.
AXIS M1045-LW Network Camera About video settings 3. Select one of the H.264 profiles. 4. Select one of the following: - Variable bit rate - Maximum bit rate 5. If you select Maximum bit rate, select which variable to prioritize in the Priority drop-down list. 6. Click Save. About Zipstream Axis’ Zipstream Technology is a bitrate reduction technology optimized for video surveillance. Zipstream reduces the average bitrate in the H.
AXIS M1045-LW Network Camera About video settings About image appearance To change Image Appearance go to the menus under Setup > Video > Camera Settings. Increasing the Color level increases the color saturation. The value 100 produces maximum color saturation and the value 0 results in a black and white image. The image Brightness can be adjusted in the range 0–100, where a higher value produces a brighter image. Increasing the Sharpness can increase bandwidth usage.
AXIS M1045-LW Network Camera About video settings • Auto to set the shutter speed automatically. If required, use Max shutter to limit the shutter speed to prevent the frame rate from being reduced. For example, to get 30 fps, set Max shutter to 1/30. • Fixed to use a fixed shutter speed. Gain, measured in decibel (dB), is the amount of amplification applied to the image. A high gain may provide a better image in low light situations but will increase the amount of image noise.
AXIS M1045-LW Network Camera About video settings The IR illumination can be activated or de-activated, and its intensity can be increased or decreased by moving the slider, from the product’s Live View page. Other settings can be defined from Setup > Video > Camera Settings. De-select the Enable IR illumination option to disable IR illumination altogether. If you disable the Synchronize IR illumination with day/night option, IR illumination will not be synchronized with day/night changes.
AXIS M1045-LW Network Camera About video settings 2. To include date and time, select Include date and Include time. 3. To include a text string, select Include text and enter the text in the field. Modifiers can be used, see File Naming & Date/Time Formats in the online help . 4. Select size, color, and placement of the text string. 5. Click Save. To modify the date and time format, go to System Options > Date & Time. See Date & Time on page 50. How to include overlay text in an action rule 1.
AXIS M1045-LW Network Camera About video settings For more examples of hexadecimal values, see the online help - . To scale the image automatically, select Scale with resolution. The image will be scaled down to fit the resolution used by the Axis product. 5. Click Save. How to include an overlay image 1. Go to Video > Overlay Image. 2. Select the image to use from the Use overlay image list and click Save. 3. Go to Video > Video Stream and select the Image tab. 4.
AXIS M1045-LW Network Camera How to configure the live view window How to configure the live view window You can customize the live view window and alter it to suit your requirements. It is possible to define the following features of the live view window. • Stream Profile. See page 20. • Default Viewer for Browser. See page 26. • Viewer Settings. See page 26. • Action Buttons. These are the buttons described in About the controls in the live view window on page 11 . • User Defined Links.
AXIS M1045-LW Network Camera How to configure the live view window About user-defined links To display user-defined links in the live view window, select the Show custom link option, give the link a name and then enter the URL to link to. When defining a web link do not remove the 'http://' from the URL address. Custom links can be used to run scripts or activate external devices connected to the product, or they can link to a web page.
AXIS M1045-LW Network Camera About PTZ (Pan Tilt Zoom) About PTZ (Pan Tilt Zoom) PTZ (pan, tilt and zoom) is available if you have enabled digital PTZ in the selected view area. For more information on view areas, see View Area on page 23. About preset positions A preset position is a saved view that can be used to quickly steer the camera to a specific position.
AXIS M1045-LW Network Camera About PTZ (Pan Tilt Zoom) The Panel Shortcut Command Buttons list shows the user-defined buttons that can be accessed from the Live View page’s Ctrl panel. These buttons can be used to provide direct access to commands issued using the VAPIX® application programming interface. Click Add to add a new shortcut command button.
AXIS M1045-LW Network Camera About detectors About detectors About camera tampering Camera Tampering can generate an alarm when the camera is repositioned, or when the lens is covered, spray-painted or severely de-focused. To send an alarm, for example via email, an action rule must be set up. How to configure tampering detection 1. Go to Detectors > Camera Tampering. 2. Set the Minimum duration, that is the time that must elapse before an alarm is generated.
AXIS M1045-LW Network Camera About detectors Once motion detection windows are configured, the Axis product can be configured to perform actions when motion is detected. Possible actions include uploading images and start recording. For more information, see How to set up action rules on page 40. Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera.
AXIS M1045-LW Network Camera About detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window, and select a low object size. • To avoid triggering on small objects, select a high object size. • While monitoring an area where moving objects are not expected, select a high history level. This will cause motion detection to trigger as long as the object is present in the window. • To only detect flashing light, select a low sensitivity.
AXIS M1045-LW Network Camera About applications About applications AXIS Camera Application Platform (ACAP) is an open platform that enables third parties to develop analytics and other applications for Axis products. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications Note • Several applications can run at the same time but some applications might not be compatible with each other.
AXIS M1045-LW Network Camera AXIS Video Motion Detection AXIS Video Motion Detection AXIS Video Motion Detection is an application that detects moving objects in the camera’s field of view. When a moving object is detected, AXIS Video Motion Detection sends an alarm that can be used by the Axis product or by third-party software to for example, record video or send a notification. AXIS Video Motion Detection 3 is included with the Axis product and is available under Setup > Applications.
AXIS M1045-LW Network Camera AXIS Video Motion Detection 6. If too many unwanted objects are detected, enable and configure one or more of the ignore filters. See Ignore Filters on page 36. 7. If too many unwanted objects are tracked, enable and configure one or more of the ignore filters. See Ignore Filters on page 36. After modifying a setting, click Save to apply the changes. The video stream will be restarted and it may take a few seconds before the change is applied.
AXIS M1045-LW Network Camera AXIS Video Motion Detection • To move a point, click and drag the point to the new position. • To move the exclude area, place the mouse pointer inside the area. When the pointer becomes a cross, drag the area to the new position. • To select an exclude area, click on the border. • To remove an exclude area, select the area and then click Remove. • To highlight the exclude areas, click on the icon.
AXIS M1045-LW Network Camera AXIS Video Motion Detection Ignore filters are applied to all moving objects found by the application and should be configured with care to ensure that no important objects are ignored. Only use ignore filters if needed and use as few filters as possible. Enable and configure one filter at a time and use visual confirmation to verify the settings before enabling another filter.
AXIS M1045-LW Network Camera AXIS Video Motion Detection The filter size can also be set by entering a value between 10 and 50 in the field. The value corresponds to the distance from the center of the cross to one of the arrowheads. The value 50 implies that an object must travel from its initial point to one sixth of the image width or height before being tracked.
AXIS M1045-LW Network Camera AXIS Video Motion Detection 2. Click Small objects. 3. Click Enable. 4. Click on the icon to show the filter size in the image. 5. Use the mouse to adjust the filter size. Start with a small size. Moving objects that fit inside the rectangle will be ignored. The filter displayed in the image can be moved to make it easier to compare the filter size with the size of objects in the image.
AXIS M1045-LW Network Camera About events About events The event pages allow you to configure your product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS M1045-LW Network Camera About events • • • - Moving – Trigger the rule when the camera view moves due to a PTZ operation. This can for example be used as an additional condition to prevent an action rule triggered by motion detection to record video while the camera view moves due to a PTZ operation. - Preset Reached – Trigger the rule when the camera stops at a preset position. This can be for example be used with the Send Images action to upload images from the preset position.
AXIS M1045-LW Network Camera About events How to add recipients The product can send media files and messages to notify users about events. Before the product can send media files or notification messages, you must define one ore more recipients. For information about available options, see About recipient types on page 42. To add a recipient: 1. Go to Events > Recipients and click Add. 2. Enter a descriptive name. 3. Select a recipient Type. 4. Enter the information needed for the recipient type. 5.
AXIS M1045-LW Network Camera About events Network Share A network share can also be used as a storage device for recorded video. Go System Options > Storage to configure a network share before setting up a continuous recording or an action rule to record video. For more information about storage devices, see Storage on page 59.
AXIS M1045-LW Network Camera About events 3. Click OK. To use the recurrence in an action rule, first select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list. To modify or remove recurrences, select the recurrence in the Recurrences List and click Modify or Remove.
AXIS M1045-LW Network Camera About recordings About recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 46. • To set up action rules, see page 40. • To access recordings, see How to find recordings on page 45. • To play recordings, see How to play recordings on page 45. • To export a recording as a video clip, see How to export a video clip on page 46.
AXIS M1045-LW Network Camera About recordings To play a recording, follow these steps: 1. Go to Recordings > List. 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the filters. See also How to find recordings on page 45. 3. Select the recording and click Play. The recording will be played in a new browser window. How to export a video clip Recordings on the SD card or network share can be exported as video clips.
AXIS M1045-LW Network Camera About languages About languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS M1045-LW Network Camera About system options About system options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS M1045-LW Network Camera About system options HTTPS HTTPS (HyperText Transfer Protocol over Secure Socket Layer, or HTTP over SSL) is a web protocol providing encrypted browsing. HTTPS can also be used by users and clients to verify that the correct device is being accessed. The security level provided by HTTPS is considered adequate for most commercial exchanges. The Axis product can be configured to require HTTPS when users from different user groups (administrator, operator, viewer) log in.
AXIS M1045-LW Network Camera About system options About certificates Certificates are used to authenticate devices on a network. Typical applications include encrypted web browsing (HTTPS), network protection via IEEE 802.1X and secure upload of images and notification messages for example via email. Two types of certificates can be used with the Axis product: Server/Client certificates - To authenticate the Axis product.
AXIS M1045-LW Network Camera About system options The Date & Time Format Used in Images is the date and time format displayed as a text overlay in the video stream. Use the predefined formats or see File Naming & Date/Time Formats in the online help for information on how to create custom date and time formats. To include date and time in the overlay text, go to Video and select Include date and Include time. Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6.
AXIS M1045-LW Network Camera About system options Linux/Unix syntax arp -s temp ping -s 408 Linux/Unix example arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125 Windows syntax (this may require that you run the command prompt as an administrator) arp -s ping -l 408 -t Windows example (this may require that you run the command prompt as an administrator) arp -s 192.168.0.
AXIS M1045-LW Network Camera About system options Advanced TCP/IP Settings DNS Configuration DNS (Domain Name Service) provides the translation of host names to IP addresses. The DNS settings are configured under System Options > Network > TCP/IP > Advanced. Select Obtain DNS server address via DHCP to use the DNS settings provided by the DHCP server.
AXIS M1045-LW Network Camera About system options NAT traversal (port mapping) for IPv4 A network router allows devices on a private network (LAN) to share a single connection to the Internet. This is done by forwarding network traffic from the private network to the “outside”, that is, the Internet. Security on the private network (LAN) is increased since most routers are pre-configured to stop attempts to access the private network (LAN) from the public network (Internet).
AXIS M1045-LW Network Camera About system options • Mode shows the type of network, for example Master (an access point). • Security shows the type of security the network uses. • Channel shows the wireless channel currently in use. • Signal strength shows the quality, the strength, of the signal. • Bit rate shows the current bit rate in Mbit/s. This can only be shown for the access point currently in use. Click Refresh to perform a new scan.
AXIS M1045-LW Network Camera About system options If applicable, select the Network type. Select Master to access the network via an access point to access any other wireless device and create a local network. About wireless certificates Wireless network certificates are used to authenticate devices on a wireless network. Wireless networks using the WPATM-/WPA2-Enterprise security method are protected by EAPOL (Extensible Authentication Protocol Over Lan), which is part of the IEEE 802.1X standard.
AXIS M1045-LW Network Camera About system options 5. Enter the user Identity associated with your certificate. 6. Select the EAPOL version (1 or 2) as used in the access point. 7. Select the CA certificate and the client certificate to use for wireless authentication. 8. Click Save.
AXIS M1045-LW Network Camera About system options SOCKS is configured under System Options > Network > SOCKS. For more information, see the online help . QoS (Quality of Service) QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.
AXIS M1045-LW Network Camera About system options RTP/H.264 The RTP port range and multicast settings are configured under System Options > Network > RTP. The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used. Select Always Multicast Video to start multicast streaming without opening an RTSP session. Bonjour The Axis product includes support for Bonjour.
AXIS M1045-LW Network Camera About system options 1. Open the Axis product’s webpages and go to Setup > System Options > Storage. 2. Click SD Card. 3. Click Unmount. 4. The card can now be removed. How to format the SD card NOTICE TICE NO Formatting the SD card will remove all data and recordings stored on the card. The Axis product can be configured to automatically format SD cards that are inserted into the product.
AXIS M1045-LW Network Camera About system options 4. Click Encrypt. 5. Select Enable SD card encryption and enter a passphrase. 6. Back in Storage Management, click Format to format the SD card. 7. Click Mount to mount the SD card. It is possible to change the passphrase without reformatting the card. Open Storage Management, click Encrypt and enter the old and new passphrases. The passphrase can only be changed when the card is mounted. Changing the passphrase does not disrupt ongoing recordings.
AXIS M1045-LW Network Camera About system options • the subnet mask • the system time • the IEEE 802.1X settings • the wireless settings Note If the Axis product is restored, uploaded applications and their settings are removed. Click Default to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The Axis product can also be reset to factory default using the control button, see How to reset to factory default settings on page 63.
AXIS M1045-LW Network Camera About system options Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NOTICE TICE NO Improper use may cause unexpected behavior and loss of contact with the Axis product. Axis strongly recommends that you do not use this function unless you understand the consequences. Axis Support does not provide assistance for problems with customized scripts. To open the Script Editor, go to System Options > Advanced > Scripting.
AXIS M1045-LW Network Camera Troubleshooting Troubleshooting How to check the current firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS M1045-LW Network Camera Troubleshooting 3. Open a browser and type in the product’s IP address. In the page that opens, use the Browse button to select the upgrade file to use. Then click Load to restart the upgrade process. 4. After the upgrade is complete (1–10 minutes), the product automatically restarts and shows a steady green on the Status indicator. 5. Reinstall the product, referring to the Installation Guide.
AXIS M1045-LW Network Camera Troubleshooting The product is accessible locally but not externally Router configuration To configure your router to allow incoming data traffic to the Axis product, enable the NAT-traversal feature which will attempt to automatically configure the router to allow access to the Axis product, see NAT traversal (port mapping) for IPv4 on page 54. The router must support UPnPTM. Firewall protection Check the Internet firewall with your network administrator.
AXIS M1045-LW Network Camera Troubleshooting Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur. To identify the source of the problem, check the System Log under System Options > Support > Logs & Reports. Depending on the problem, it might be necessary to re-mount the storage device.
AXIS M1045-LW Network Camera Technical specifications Technical specifications You can find the latest version of the technical specifications at www.axis.com Camera Image sensor 1/3" progressive scan RGB CMOS Lens Fixed focal length, 2.8 mm, F2.0 Horizontal field of view: 110° Vertical field of view: 61° M12 mount, fixed iris, IR corrected Day and night Automatically removable IR cut filter Minimum illumination Color: 0.25 lux at 50 IRE F2.0 B/W: 0.05 lux at 50 IRE F2.
AXIS M1045-LW Network Camera Technical specifications Video recording to edge storage, Activation of IR-LED, Overlay text Pre- and post-alarm video buffering Data streaming Event data Built-in installation aids Pixel counter 69
AXIS M1045-LW Network Camera Technical specifications General Casing Polycarbonate, Aluminium, recycled plastic Color: White NCS S 1002-B For repainting instructions of skin cover or casing and impact on warranty, contact your Axis partner. Sustainability PVC free, 64% recycled plastic Memory 512 MB RAM, 256 MB Flash Power 4.75–5.25 V DC, typical 2.7 W, max 4.4 W IR illumination IR illumination, LED with adjustable intensity.
AXIS M1045-LW Network Camera Technical specifications The following factors are among the most important to consider: • High image resolution and/or lower compression levels result in images containing more data. Bandwidth affected. • Access by large numbers of Motion JPEG and/or unicast H.264 clients. Bandwidth affected. • Simultaneous viewing of different streams (resolution, compression) by different clients. Effect on frame rate and bandwidth. • Accessing Motion JPEG and H.
User Manual AXIS M1045-LW Network Camera © Axis Communications AB, 2016 Ver. M3.2 Date: December 2016 Part No.
