User Manual

ManualsBrandsAxis ManualsComponents & AccessoriesT8120 Midspan 15 W 1-port PoE injector - 15 Watt

USER GUIDE

ENGLISH

AXIS T8120 Midspan 15 W 1-port

Summary of content (10 pages)

PAGE 1
USER GUIDE ENGLISH AXIS T8120 Midspan 15 W 1-port
PAGE 2
Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. Electromagnetic Compatibility (EMC) USA - Using an unshielded network cable (UTP): This equipment has been tested using an unshielded network cable (UTP) and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 3
AXIS T8120 Page 3 AXIS T8120 User Guide Safety Information • When transporting the Axis product, use the original packaging or equivalent to prevent damage to the product. • Store the Axis product in a dry and ventilated environment. • Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for service matters. • The product should connected to PoE networks only, without routing to the outside plant. • Only qualified personnel can install or remove the product.
PAGE 4
Page 4 AXIS T8120 • The AC wall socket outlet must be near the product and easily accessed. AC power can be removed from the product by disconnecting the AC power cord from either the wall socket-outlet or from the products appliance coupler. • The products “DATA IN” and “DATA & POWER OUT” interfaces are qualified as Safety Extra-low Voltage (SELV) circuits according to IEC 60950-1. These interfaces can only be connected to SELV interfaces on other equipment.
PAGE 5
AXIS T8120 Page 5 Functions and Features The Power over Ethernet (PoE) Midspan adds 48V DC to unused (nondata) wires (Mode B) in a standard Category 5 Ethernet cable. As a result, the PoE Midspan delivers both data and power to the terminal. The device is designed to meet the IEEE802.3af standard. • Ensure AC power is applied to the PoE Midspan using an operational AC cable with an appropriate ground connection. • Ensure that output Ethernet cable is connected to the Data & Power Out port.
PAGE 6
Page 6 AXIS T8120 Installing the Unit 1. 2. 3. Connect the PoE Midspan to an AC outlet (100-240 V AC), using a standard power cable. Connect the unit Data In jack (input) to the remote Ethernet network switch Patch panel. Connect the Data & Power Out jack (output) to the terminal.
PAGE 7
AXIS T8120 Page 7 Specifications Environmental Specifications Mode Temperature Humidity Operating 0 °C to 40 °C (32 °F to 104 °F) 10 to 90% RH (no condensation -20 °C to 70 °C (-4 °F to 158 °F) allowed) Storage Input voltage 100 to 240V AC (50/60 Hz) Input current 0.5 A (maximal) Available Output Power (Maximum) 16.
PAGE 8
Page 8 AXIS T8120 Troubleshooting Symptom Corrective Steps Midspan does not power up 1. 2. 3. Verify that an approved power cord is used. Verify that the voltage at the power inlet is between 100 and 240V AC. Remove and re-apply power to the device and check the indicators during power up sequence. A port indicator is not lit 1. The Midspan did not detect a device and and the Midspan does not therefore the port is not enabled. operate 2. Verify that the device is designed for PoE operation 3.
PAGE 9
Liability Every care has been taken in the preparation of this document. Please inform your local Axis office of any inaccuracies or omissions. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and documentation without prior notice.