Service manual

11
PROGRAMMING
GENERAL INFORMATION
In order to fully utilize the many features of your
vender it is important that you first understand the
options available and procedures for programming the
vending controller unit (control board).
All programming, testing, and service functions are
accomplished by using the keypad in an easy to
follow, display prompted format. In stand alone
operation there are four modes of operation for
servicing, testing, and setting up your vender. If
attached to a snack vender there are five modes of
operation for servicing, testing, and setting up your
venders. The modes of operation are accessed by,
opening the service door, and pressing the service
button on the control board.
The service button will cycle through each of the four
(five) modes in turn: Service Mode, Test Mode, Set-
Up Mode 1, Set-Up Mode 2, and Satellite Mode (if a
snack vender is attached). In each of these modes,
the “A” key is used to scroll through the available
options/settings within that mode/selection. (Note: In
each of the mode selections, pressing the character
key next to the listed option will take you directly to
that feature - see menu items chart on page 13.), the
“” key is used as an enter key to select the currently
displayed item/feature, and the “CLR” key is used as a
done or exit key. Closing the service door or pushing
the service door switch will exit the function you are
currently in and place the vender back in service.
EXTERNAL DISPLAY ITEMS
(HOT KEYS)
Allows the service technician to view several items via
the display without opening the vender. There are four
options that can be viewed externally:
1. Display temperature in degrees “C”. To
view, press the “C” then press the  key. The
display will then show the vender’s inside
temperature in degrees “C”.
2. Display date/time. To view, press the “D”
key, then press the “” key. The display will
then show the current date and time.
3. Display temperature in degrees “F”. To
view, press the “F” key, then press the “”
key. The display will show the vender’s inside
temperature in degrees “F”.
4. Display current software revision. To view,
press the “B” key, then press the “” key. The
display will then show the current software
revision in the controller.
NORMAL OPERATION MESSAGES
At initial power-up, the program will start and the
display will briefly show the software version in use as
Software ###.## (i.e. 700.31), followed by the default
idle message, “ENJOY A REFRESHING DRINK” or
“ENJOY A REFRESHING DRINK AND SNACK” when
attached to a snack vender..
INITIAL PROGRAMMING
DATE/TIME
To set date/time enter “SETUP MODE 1” by opening
the service door and pressing the Service Button
three (3) times. Press the number “5” and
“DATE/TIME” will show on display. Press the “” key
and display will show the current year, month, date,
and time setting currently in the system in following
format: 2005 Apr 28 15:45 with the year highlighted.
Press the numbers to enter the current year and
Month will then be highlighted. To change the month
press the A key to scroll forward through the months
or the B key to scroll backward through the months.
With the correct month showing, press the “” key to
save and Date will then be highlighted. Press the
numbers to enter the current date and then the hour
will then be highlighted. Note: Hours are shown in 24
hour format. Press the numbers to enter the current
hour and then the minutes will then be highlighted.
Press the numbers to enter the current minutes. The
display will then change to show “OK? =Y (Yes)
CLR = N (No)” and the setting you entered. You must
press  Key to save the new date and time entered.
Pressing CLR Key will revert to the date and time
setting. Press the “CLR” key to return to “SETUP
MODE”.
SET PRICES
To set the prices enter the “SERVICE MODE” by
opening the service door and pressing the Service
Button once. Allows the setting of regular and
secondary prices for an individual item, a complete
tray, or the entire machine. Factory setting is $99.95.
Press the number “7” on the keypad and the display
will show “SET PRICE”. Press the “” key and the
display will show “1 = Regular Pricing, 2 = Secondary
Pricing”. To set regular prices press number 1 key
and display will show “Regular $##.##”. To set price:
1. All selections. Press the keypad numbers of
the price you wish to use. As numbers are
entered the numbers will shift in from the right
as they are entered. Note: The CLR key will
remove the last # of the price. Once the
desired price is showing on the display press
the “” key and the display will show
“PR$##.## All Set”, press “*” to set more
prices or CLR to return to SET PRICES.
Press CLR Key again to return to SERVICE
MODE.
2. One tray. Press the keypad numbers of the
price you wish to use. As numbers are
entered the numbers will shift in from the right
as they are entered. Note: The CLR key will
remove the last # of the price. Once the
desired price is showing on the display press
the tray letter desired for setting price. Press