Service manual

16
B(tray letter) Row Set”, press “*” to set more
prices or CLR to exit to SET PRICE.
3. Single selection. Press the keypad
numbers of the price you wish to use. As
numbers are entered the numbers will shift
in from the right as they are entered. Note:
The CLR key will remove the last # of the
price. Once the desired price is showing on
the display press the selection desired for
setting price. Press “” and display will
show “PR $##.## B1 Selection Set”, press
“” to set more prices or CLR to exit to SET
PRICE.
The last price entered for a selection is the one that
is used. For example, If one price on the A tray was
set to $1.50 using option 3 above and you wish to
change the remaining selections on that tray using
option 2, the pricing for the entire tray would take
precedence. Conversely, if the price was set using
option 2 first followed by the single selection using
option 3, the pricing for the remainder of the shelf
would remain and the new price for the single
selection would change to the new value. Press the
“CLR” key to return to “Set Prices”. Press the “CLR”
key to return to “SERVICE MODE” or press the “A”
key to advance to the next menu item below.
SET SHELF LOCATION - Key “8”
Allows the service technician to program the
electronics to match the seven different settings
available for the shelves. These settings are
available to vend different package heights. The
factory default setting is Shelf Setting D. Press the
number “8” on the keypad and display will show “Set
Shelf Location”. Press the “” key and display will
show current setting. To change the setting press
one of the following: A = G setting, B = M1 setting, C
= M2 setting, D = D setting, E = E setting, F = E1
setting, D2 = BM3 5800-4 setting. Note G, M1, &
M2 settings are used in venders prior to 0001-
8487AE and D, E, & E1 settings are used in venders
0001-8487AE & higher, D2 is setting used in all
domestic BevMax 3 5800-4 venders. Once the
desired setting is showing on the display press the
“” key to save the setting. Note: all shelf settings
have to be physically set to match the programmed
setting. You can not set the physical shelf settings
differently. Press the “CLR” key to return to “Set
Shelf Location”. Press the “CLR” key to return to
“SERVICE MODE” or press the “A” key to advance
to the next menu item below.
RELAY TOGGLE - Press key “9”
Allows the service technician to test the Light Relay,
Fan Relay, and Compressor Relay. Press the
number “9” on the keypad and the display will show
“Relay Toggle”. Press the “” Key and display will
show “Light A – On or Off”, “Fan B – On or Off”,
“Compressor C – On or Off”. Display will show
current status of the relay (not the component the
relay operates). To toggle the state of a given relay
press the letter key associated with it on the display.
Caution: Disconnect power to the compressor before
testing the compressor relay. Failure to disconnect
power to the compressor before testing the relay
could result in damaging the compressor. Press the
“CLR” key to return to “Relay Toggle”. Press the
“CLR” key to return to “SERVICE MODE” or press
the “A” key to advance to the next menu item below.
CLEAR ERRORS - Press key “0”
Allows the service technician to clear errors
recorded in the venders data. Press the number “0”
Key and the display will show “CLEAR ERRORS”,
then press “” Key and the display will show “Clear
All Errors?  = Y CLR = N”. Press the “CLR” key to
return to “Clear Errors”. Press “” Key to clear all
errors or press the “CLR” key to return to “SERVICE
MODE”.
TEST MODE
Enter TEST MODE by opening the service door and
pressing the blue Service button twice. The display
will read” TEST MODE”.
NEXT ITEM - Press key “A”
LIST ERRORS - Press key “B”
Allows the service technician to view a list of all
recorded errors. Press the letter “B” on the keypad
and the display will show “LIST ERRORS”, then
change to “NONE” if no errors exist or, if errors are
present, one of the error prompts below will be
displayed. If an error code is displayed, press the
“” key to view the next error until “END LIST” is
displayed. With “END LIST” showing on the display,
press the “” key to clear errors and return to TEST
MODE. If you wish to exit the list without clearing
errors, simply push the “CLR” key and the display
will return to LIST ERRORS. If the CLR key is
pressed prior to reaching the end of the list, the
display will jump to END LIST. Explanations for the
error codes are listed below. Note: The prompts
listed will only show on the display if an error has
occurred.
NONE
No errors have occurred.
VEND MECH ERROR
HORIZ – Horizontal Drive System problem.
VERT – Vertical Drive System problem.
PICKI – Picker not all the way in problem.
PICKO – Picker out switch error problem.
PORT – Port Drive System problem.
VS – Vend Sensor problem.
VMC ERRORS
FRAM – Memory module read/write error.
RTC – RTC read/write error, clock error.
SF – Decimal error.
RCRC – software not loaded properly.