Service manual

19
LED on the controller also will be on
when a “1” is displayed.
“Hm” indicates whether the picker home
switch is closed. A “1” indicates that
the picker home switch is closed
(plunger at home position) and a “0”
indicates it is opened. This switch is
moved by the plunger, pulling the
plunger out by hand will turn the switch
off. The Red LED on the controller will
also be on when a “1” is displayed.
• Key 4 = Repeat Vend. Press the number 4 key
and the display will show “Current Vend:
#########” and start auto test vending each
column. Press the “CLR” key to stop the test
• Key 5 = Vend Error Codes – Caution: Factory
Use Only do not use.
• Key 6 =
Product Sensors. Press key 6 and the
display will show “Product Sensors On”. Press
the “” key to toggle the Product Sensors to the
Off setting. Factory default setting is on. Note
Product Sensors Off setting is used in BevMax 2
Pepsi Venders prior to 8625CF and Generic
Venders prior to 8600AG. Product Sensors On
is used in all BevMax 3 5800-4 Venders
.
• Key 7 = Turns off vend mech for software test.
Caution: Factory use only for peripheral
testing, do not use.
• Key 8 = Adjust Shelf (Y) Offset (up and down).
Press the number 8 key and the display will
show “Shelf Offset ####, 3310 counts = 1 inch”.
To change the offset enter a new number and
press the “” key to save and display will show
“#### Offset recorded. Then press “CLR to go
back to “Factory Diagnostics”. Go back to
Position Test and check the plunger is
contacting the targets correctly.
• Key 9 = Not used at this time.
• Key 0 = Adjust Hook Swipe “X” Offset (left to
right). Press the number “0” key and the display
will show “Hook Swipe ####, 3310 counts = 1
inch”. For factory default setting see born on
label settings listed on service door. To change
the off set, pull the top left (white) door switch in
the out position to power the XY motors. Press
the “” key once will automatically run the
Delivery Cup Assembly to the swipe position
and allow specific vender coordinates to be
changed and saved in the control board
memory. Use the numbers on the key pad to
change the coordinates. Press the “” key to
save the new setting and the Delivery Cup Assy.
will automatically go to the “Home” position, then
move back to the swipe position again. Press
the “” key to send the Delivery Cup Assy. back
to the “Home” position and the programming will
return to “Factory Diagnostics”. Press “CLR”
key to return to “Test Mode”. Then go to “Test
Vend” and test for proper delivery of product in
the Port Assy. of the Service Door.
Press the “CLR” key to return to “Factory
Diagnostics”. Press the “CLR” key to return to “TEST
MODE” or press the “A” key to advance to the next
menu item below.
TUBE FILL/DISPENSE - Press key “1”
Allows the service technician to inventory currency in
the coin mechanism escrow tubes and “Teach” the
controller how many coins of each denomination are
in that inventory. This allows for the maximum
number of dollar bills to be accepted prior to
enabling the “USE EXACT CHANGE” function. This
also provides for exact cash accountability in the
audit functions. This function can also be used as a
diagnostic tool to insure the coin mechanism is
responding properly. Press the number “1” on the
keypad and the display will read
‘TUBEFILL/DISPENSE”. Press the “” key and the
display will show the lowest denomination accepted
and the number of these coins inventoried. Press
the letter “A” on the keypad to show through the
denominations available. With a given denomination
displayed, an inserted coin of this denomination via
the coin chute will increase the inventory shown.
Note: When you insert any denomination the display
will change to show the denomination inserted. To
dispense: while in the tube fill/dispense mode go to
the coin mech and press the coin mech dispense
button(s) for the tube you wish to dispense from or
press the  Key and the denomination displayed will
be dispensed to the coin cup and the inventory will
be decreased. Press the “” Key again to stop the
coins from being dispensed. Press the “CLR” key to
return to “Tube Fill/Dispense”. Press the “CLR” key
to return to “TEST MODE” or press the “A” key to
advance to the next menu item below.
DAYLIGHT SAVINGS TIME - Press key “2”
Allows the service technician to enable daylight
savings time to be set as it applies to the selected
Daylight Savings Rules Setting. Press the “” key
to show the current setting. Press the “A” key to
scroll through the different settings that are
available. With the setting you wish to use showing
on the display, press the “” key.
• OFF – No Daylight Savings Time
• American Rules. If enabled, the VCU will
set the clock back one hour on the last
Sunday of October (2:00 AM), set the clock
ahead one hour on the first Sunday in April
(2:00 AM).
• European Rules. If enabled, the VCU will
set the clock back one hour on the last
Sunday of October (1:00 AM), set the clock
ahead one hour on the last Sunday in
March (1:00 AM).