Service manual

ManualsBrandsAxis ManualsComputer equipment5800

♦ When enabling or disabling single selections the

opposite state of the current setting will be used. For

example: if you currently have selection 210 enabled

and you go into change it, it will change to disabled.

♦ When enabling or disabling a range, shelf or the

entire machine. The setting will change to the

opposite of the lowest selection number in the

range, shelf or machine being set. For example if

you are changing the top shelf, and selection 210 is

set to enable while 212 -216 are set to disable, then

you would be disabling the top shelf from Golden-

Eye because the lowest selection number on the

shelf was set to enable.

CHECK MOTOR SCAN

This function is used to verify the state of the

selection motors in the Satellite (MultiMate). To

access this Mode, press the Service Switch 5 times,

then press 3 on the selection keypad the display will

show the results of the last Motor Scan Test. Press

the “

” key to scroll through the results. To initiate

a new scan of the motors Press the 1 key. The

display will say Scanning Motors when

completed the display will say Scanning motors

done press “

” to continue. Press the “” key to

scroll through the results.

Set Credit Ret TO

This function is used to set the amount of time the

customer has to make another selection before their

change is returned. During this time period, the

customer can make a selection, add more money to

make another selection or press the coin return to

receive their change. To access this mode, press the

Service Switch 5 times, then press 4 on the selection

keypad the display will show “Set Credit Ret TO”.

Press the “

” key the display will show “Set Credit

Return” in the top line and “Timeout : XX:XX in the

bottom line, where XX:XX is the currently set

timeout. Use the numeric keypad to enter the

minutes and seconds. Press the “

” key to lock in

the change.

NOTE: The default time is 30 seconds.

Minimum time is 00:00

Maximum time is 05:00

Major Component Description

AC DISTRIBUTION BOX

BevMax 3 5800-4

110 VAC units

Main Power Switch / Plug Interrupts hot side

of incoming power

to all components in

machine.

15 Amp Outlet (110 VAC) Provides power to

Refrigeration unit.

Transformer (T1) Provides 24 Volt

power to the

Controller Board.

Service Door Switches

If 2 Switches - Left Switch (10 Amp) – in XY Motor

Circuits, Port Door Motor Circuit, and Picker Motor

Circuit (Power Interrupt Switch).

If 2 Switches - Right Switch

(.1 Amp) – in

Controller and Electronic Lock Circuit (Lock Switch).

If One Switch

- the red & black wires are in

Controller Circuit and the two gray wires are go to

XY Motor Circuits, Port Door Motor Circuit, and

Picker Motor Circuit. (Power Interrupt Switch).

General Maintenance

The most important facets of proper care and

maintenance of your machine are the electrical

power supplied to it, leveling, and cleanliness of the

machine.

POWER

The machine must be connected to a dedicated 120

VAC, 15 Amp circuit (U.S. and Canada).

CAUTION:

REMOVE POWER TO THE AC DISTRIBUTION

BOX BEFORE CLEANING OR WHEN ANY

ELECTRICAL COMPONENTS ARE CONNECTED /

DISCONNECTED FOR TESTING OR

REPLACEMENT.

Periodically inspect the power supply

cord for damage. If the cord or plug is

worn or damaged, it must be replaced

with a power supply cord of the same

type, size and specification as originally

provided with the machine. DO NOT

USE THE VENDING MACHINE UNTIL

THE WORN OR DAMAGED CORD IS

REPLACED.

The Ground Fault Circuit Interrupter (GFCI) must be

tested frequently and before each use in accordance

with the instructions provided on the GFCI device.

IF THE GFCI DOES NOT PASS THE TEST, DO

NOT USE THE MACHINE. Unplug the supply cord

from the receptacle and call the Dixie-Narco

Technical Support Group for assistance at 1-803-

266-5001.