INSTALLATION GUIDE ENGLISH AXIS A1001 Network Door Controller
Liability Every care has been taken in the preparation of this document. Please inform your local Axis office of any inaccuracies or omissions. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice.
Safety This product complies with IEC/EN/UL 60950-1, Safety of Information Technology Equipment. The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) according to IEC/EN/UL 60950-1. Disposal and Recycling When this product has reached the end of its useful life, dispose of it according to local raws and regulations.
AXIS A1001 Network Door Controller Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE Indicates a situation which, if not avoided, could result in damage to property.
AXIS A1001 Network Door Controller Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NOTICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing. • Store the Axis product in a dry and ventilated environment. • Avoid exposing the Axis product to shocks or heavy pressure.
AXIS A1001 Network Door Controller WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. 7 ENGLISH • Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
AXIS A1001 Network Door Controller Installation Guide Installation Steps 1. Make sure the package contents, tools and other materials necessary for the installation are in order. See page 9 . 2. Study the hardware overview. See page 11. 3. Study the specifications. See page 16. 4. Install the hardware. See page 22. 5. Access the product. See page 30.
AXIS A1001 Network Door Controller Recommended Tools • • • • • Drill – if mounting on wall or ceiling Screwdriver – if mounting on wall or ceiling Slotted screwdriver – for opening the cover Torx screwdriver (T10) – for tightening the cover screw Wire stripping tool Optional Accessories • • • • NOTICE AXIS T8120 Midspan 15 W AXIS T8128 PoE Splitter 24 V (requires 30 W midspan) AXIS T8129 PoE Extender Mains adaptor 24 V DC AXIS T98A15-VE Surveillance Cabinet In outdoor installations combining AXIS A1001 a
AXIS A1001 Network Door Controller Hardware Overview ENGLISH 1 2 3 4 5 6 7 8 Front and back: 1 Cover 2 Cover screw 3 Cover removal slot 4 Base 5 DIN clip – upper 6 Tampering alarm switch – back 7 DIN clip – lower 11
AXIS A1001 Network Door Controller 8 Part number (P/N) & Serial number (S/N) 1 4 2 6 3 5 8 7 9 10 11 12 I/O 1 10 3 8 4 7 6 5 interface: Reader data connector (READER DATA 1) Reader data connector (READER DATA 2) Reader I/O connector (READER I/O 1) Reader I/O connector (READER I/O 2) Door connector (DOOR IN 1) Door connector (DOOR IN 2) Auxiliary connector (AUX) Audio connector (AUDIO) (not used) External power inputs: 2 Power connector (DC IN) 12 Network connector (PoE) Power outputs: 9 Power loc
AXIS A1001 Network Door Controller 2 1 3 4 5 ENGLISH 6 7 13 8 12 9 11 LED 1 2 3 4 5 6 7 8 9 10 11 12 13 10 indicators, buttons and other hardware: Power LED indicator Status LED indicator Network LED indicator Reader 2 LED indicator (not used) Reader 1 LED indicator (not used) Tampering alarm pin header – front (TF) Tampering alarm pin header – back (TB) Lock LED indicator Lock LED indicator Tampering alarm sensor – front SD card slot (microSDHC) (not used) Control button Part number (P/N) & Seria
AXIS A1001 Network Door Controller LED Indicators LED Color Indication Network Green Steady for connection to a 100 MBit/s network. Flashes for network activity. Amber Steady for connection to a 10 MBit/s network. Flashes for network activity. Unlit No network connection. Green Steady green for normal operation. Amber Steady during startup and when restoring settings. Red Slow flash for failed upgrade. Green Normal operation. Amber Flashes green/amber during firmware upgrade.
AXIS A1001 Network Door Controller • Digital output – For connecting, for example, reader beepers and reader LEDs. Door Connector Two 4-pin terminal blocks for connecting door monitoring devices and request to exit (REX) devices • • Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example PIR sensors or glass break detectors. Digital output – For connecting external devices such as burglar alarms, sirens or lights.
AXIS A1001 Network Door Controller Control Button The control button is used for: • • Resetting the product to factory default settings. See page 35. Connecting to an AXIS Video Hosting System service or AXIS Internet Dynamic DNS Service. For more information about these services, see the User Manual. Specifications Operating Conditions The Axis product is intended for indoor use.
AXIS A1001 Network Door Controller Connectors For information about the connectors’ positions, see Hardware Overview, on page 11. The following section describes the connectors’ technical specifications. Reader Data Connector 6-pin terminal block supporting RS485 and Wiegand protocols for communication with the reader.
AXIS A1001 Network Door Controller Reader I/O Connector 6-pin terminal block for: • • • • Auxiliary power (DC output) Digital Input Digital Output 0 V DC (-) Function Pin Notes 0 V DC (-) 1 DC output 2 For powering auxiliary equipment. Note: This pin can only be used as power out. 12 V DC Max load = 300 mA Configurable (Input or Output) 3–6 Digital input — Connect to pin 1 to activate, or leave floating (unconnected) to deactivate.
AXIS A1001 Network Door Controller Auxiliary Connector 4-pin configurable I/O terminal block for: Notes ENGLISH • Auxiliary power (DC output) • Digital Input • Digital Output • 0 V DC (-) For an example connection diagram, see Connection Diagrams, on page 21. Function Pin 0 V DC (-) 1 DC output 2 For powering auxiliary equipment. Note: This pin can only be used as power out. 3.
AXIS A1001 Network Door Controller Function Pin 0 V DC (-) 1 DC input 2 Notes Specifications 0 V DC For powering controller when not using Power over Ethernet. Note: This pin can only be used as power in. 10–30 V DC, max 26 W, Max load on outputs = 14 W Network Connector RJ45 Ethernet connector. Supports Power over Ethernet (PoE). When used in systems that require UL certification, the product shall be connected to UL 294B-listed network equipment.
AXIS A1001 Network Door Controller Power & Relay Connector 6-pin terminal block with built-in relay for: Notes ENGLISH • External devices • Auxiliary power (DC output) • 0 V DC (-) Connect locks and loads to the pins according to the hardware pin chart generated through the hardware configuration. Function Pin 0 V DC (-) 1, 4 Relay 2–3 For connecting relay devices. Use the hardware pin chart. See Configure the Hardware, on page 23.
AXIS A1001 Network Door Controller Auxiliary Connector 1 3.3 V max 100 mA 2 A B A B I/O configured as input I/O configured as output Install the Hardware CAUTION Never mount the Axis product while power is applied to the product. Always apply power at the end of the installation. NOTICE To protect the circuits against electrostatic discharge (ESD), use ESD protection when handling the product while the components and contacts are exposed. Read all the instructions before installing the product.
AXIS A1001 Network Door Controller System Considerations The Axis product shall be installed within the secured area. The Axis product should be installed on a wall (preferred) or a ceiling, with or without a junction box. It can also be installed on a DIN rail. Configure the Hardware Configure the hardware in the Hardware Configuration pages before installing the product. Doors, locks and other devices can be connected to the Axis product before completing the hardware configuration.
AXIS A1001 Network Door Controller 9. Disconnect the product from the network. If not powering the product through Power over Ethernet, also disconnect the product from its power source. To cancel the hardware configuration, click Cancel. This can be done in any of the hardware configuration pages. To view the hardware pin chart, go to Setup > Hardware Pin Chart. To print the hardware pin chart, click Print Hardware Pin Chart.
AXIS A1001 Network Door Controller 1 ENGLISH 2 1 2 Base Screw hole (4x) 6. Connect the cables. See page 26. DIN Rail Mount 1. If required, install a DIN rail (not included). 2. If required, remove the cover screw, insert a slotted screwdriver into the cover removal slot and remove the cover. See Hardware Overview, on page 11. 3. Hook the lower DIN clip, which is flexible, onto the bottom of the DIN rail, tilting the base slightly forwards. 4.
AXIS A1001 Network Door Controller 1 2 3 4 1 2 3 4 Base Screw hole (4x) DIN rail Lower Din clip 7. Secure the base using four screws. Make sure that the screws and plugs are appropriate for the material (e.g. wood, metal, sheet rock, stone). See Wall and Ceiling Mount, on page 24. Note To prevent bending of the base, be careful not to tighten the screws too tight. Leave approximately 2.5 mm (0.1 in). If the base is bent, the cover will not close. 8. Connect the cables. See page 26.
AXIS A1001 Network Door Controller • If using Power over Ethernet, wait with connecting the network cable to the network until the all the other wires have been connected. • To allow for future maintenance, to avoid excessive strain on wires and connectors, and to avoid damage to conductor insulation, leave a service loop and make sure all cables and wires are properly supported and secured. Use the supplied cable ties.
AXIS A1001 Network Door Controller 3. Strip the cables and wires as required using a crimp tool. 4. Connect the wires between the door controller and the locks, doors and other devices. For more information about the connectors and their specifications, see page 14 and page 17. NOTICE • Make sure all the wires are connected correctly. Incorrect wiring could cause damage to the product. • The cables shall have wire diameters that correspond to AWG 28–16 (CSA) or AWG 30–14 (CUL/UL).
AXIS A1001 Network Door Controller Note • For information about how to connect other wires, such as power wires to locks, readers and other devices, see the manufacturers’ instructions. 5. 6. 7. 8. Collect all the wires neatly and secure them using the supplied cable ties. Label the cables for future reference. If using Power over Ethernet, connect the network cable to the network. If using Ethernet and external power (10–30 V DC), connect the network cable to the network and connect power.
AXIS A1001 Network Door Controller 9. Make sure that the LEDs indicate the correct conditions. See LED Indicators, on page 14. 10. Attach the cover to the base and tighten the cover screw. 1 2 1 2 Cover Cover screw (T10) Access the Product The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems.
AXIS A1001 Network Door Controller Access from a Browser Access from the Internet Once connected, the Axis product is accessible on your local network (LAN). To access the product from the Internet you must configure your network router to allow incoming data traffic to the product. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the product.
AXIS A1001 Network Door Controller AXIS IP Utility – Small Installations AXIS IP Utility automatically discovers and displays Axis products on your network. The application can also be used to manually assign a static IP address. Note that the computer running AXIS IP Utility must be on the same network segment (physical subnet) as the Axis product. Automatic Discovery 1. 2. 3. 4. Check that the Axis product is connected to the network and has powered up. Start AXIS IP Utility.
AXIS A1001 Network Door Controller Assign IP Addresses in Multiple Devices AXIS Camera Management speeds up the process of assigning IP addresses to multiple devices by suggesting IP addresses from a specified range. 1. Select the devices you wish to configure (different models can be selected) and click Assign IP address to selected devices . 2. Click Yes in the Device Maintenance dialog. 3.
AXIS A1001 Network Door Controller Assign IP Address Using ARP/Ping The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power. 1. Acquire a free static IP address on the same network segment as the computer. 2. Locate the serial number (S/N) on the product label. 3. Open a command prompt and enter the following commands: Linux/Unix syntax arp -s temp ping -l 408 Linux/Unix example arp -s 192.168.0.
AXIS A1001 Network Door Controller To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate. HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt traffic between web browsers and servers. The HTTPS certificate ensures encrypted exchange of information. To set the password via a standard HTTP connection, enter it directly in the dialog.
AXIS A1001 Network Door Controller Further Information The User Manual is available at www.axis.com Visit www.axis.com/techsup to check if there is updated firmware available for your network product. To see the currently installed firmware version, go to Setup > About. Visit Axis learning center www.axis.com/academy for useful trainings, webinars, tutorials and guides. Warranty Information For information about Axis’ product warranty and thereto related information, see www.axis.
Installation Guide AXIS A1001 Network Door Controller © Axis Communications AB, 2013 Ver. M2.3 Date: November 2013 Part No.
