PRODUCT USER MANUAL INSTALLATION GUIDE D2 COOLDOME™ ENCLOSURE Product Models: D2-CD-12V D2-CD-24V
Table of Contents Limited Warranty Info ..………………………………………………………………………………………………………………………………………………………………………………... 0 Product Installation Precautions, Warnings, and Installation Guidelines ......................................................................................................... 1 Electrical Conduit Guidelines ..........................................................................................................................................................................
LIMITED WARRANTY DOTWORKZ, INC. PRODUCTS DOTWORKZ SYSTEMS INC. Warrants this Product to be free from defects in material or workmanship, as follows: PRODUCT CATEGORY All Enclosures and Electronics Power Supplies Accessory Brackets PARTS LABOR One (1) Year One (1) Year One (1) Year One (1) Year One (1) Year One (1) Year During the warranty period, to repair the Product the Purchaser will deliver it to Dotworkz Systems Inc. San Diego, CA, or return the defective product, freight prepaid.
PRODUCT INSTALLATION PRECAUTIONS – WARNINGS – ADDITIONAL INFORMATION (RETAIN THIS DOCUMENT) IMPORTANT SAFEGUARDS 1 Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions -The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions -All operating & user instructions should be followed. 5.
Electrical Conduit Guidelines For optimal performance, your Dotworkz Enclosure is designed to be Air & Water Tight to eliminate any moisture, dust, and insect damage, safety, performance, reliability, and maintenance related issues. Use of Electrical Conduit, without sealing the entry ports/ inside wire feeds within Camera Enclosure, will subject the inside of your enclosure to possibility of condensation driven moisture, dust, and insect contamination hazards.
VENT STOPPER PLUGS for Conduit Foam Conduit Feed Plugs for ½” I.D. (PG-13) Conduit Prevents Humid Air exchange from venting thru electrical conduit into Dotworkz sealed enclosures, Thus eliminating condensation issues within Dotworkz sealed enclosures. QUICK INSTALLATION GUIDE 1) Pull wires to final installed length. 4) Push plug into conduit mouth with finger tips till it flush with outside of fitting 2) Open Vent Stop Plug and install over wire.
Proper Cable Management to Enclosure Avoid common Installation Mistakes Only Use Qualified Installation or Service Technician for Installing & Servicing Dotworkz Enclosures. Power Must be disconnected and kept off while installing or Servicing Enclosure. Follow All Local and Applicable Electrical Codes and Standards for Installation of Electrical components. All Cable Ports, wire feeds, or Conduit must be fully sealed to eliminate moisture within Enclosure.
COOLDOME™ Wiring NO 18 gg Dotworkz D2-CD Operates using low voltage only, and creates ample currents when cooler is engaged. Follow relevant Cable Gauge Guidelines provide in this document applicable to your product model. Dedicated 12 VDC or 24 VDC models Dotworkz Humidity Removal Canister Dotworkz Provides a Humidity Removal Canister must be installed into COOLDOME prior to entering enclosure into service.
Component Check List Included Standard Hardware for Camera Mounting & Provided COOLDOME Accessories KT-HRC1 Humidity Removal Canister S-250-12V or S-250-24V Step Down Power Supply Optional BR-AXBR Camera Mount Bracket for Larger Cameras (Request BR-AXBR at time of order for listed camera models) Optional BR-AXBR Bracket Direct Compatibility: (Available by special order) Axis 231D, & 232D DVTel 9840 Merit-LiLin PIH-7000/7600/7625 PiXORD P-463T Fast Speed Dome Pelco Spectra IV Sony SNCRH124, SNC-RS44N, SNC-
Tools Recommended for Enclosure & Camera Mounting Hand Tools Drill & Bits Pole Strapping Tools - #1 & #2 Phillips head screw driver -#1 Flat Blade screw driver or smaller - 3/8 Socket wrench, nut driver, or adjustable wrench - 5/16 Socket wrench, nut driver, or adjustable wrench - 7/16 Socket wrench, nut driver, or adjustable wrench - 7/32 Socket wrench, nut driver, or adjustable wrench - 11/32 Socket wrench, nut driver, or adjustable wrench - Wire stripping tool - Caulk Gun & Silicone Sealant For Wall M
Low Voltage Line Drop Wire Gauge Tables See 12 VDC & 24 VDC Wire Gage Selector Charts – Next Page 8
Wire Gage Selector Charts 9
10
Camera Power Connection Camera Power Setup (STANDARD 12VDC Camera PowerCONNECTOR) Setup (STANDARD 12VDC CONNECTOR) The D2-CD-12V provides an 18” lead from the COOLDOME power circuit with the following common 12 VDC Barrel connector, which is nearly and industry standard. Dotworkz provides the Right Angle version below. All D2 environmental enclosures come standard with a 12VDC Right Angle Barrel Plug (3.3mm x 5.
12
Stand Off Assembly Key for Camera Height Adjustment Camera mount stand offs can be adjusted to any height from 0” to 3.75” using assembly logic illustrated above. By utilizing both the camera mounts inside the D2; the upper mounts, and the lower mounts around the lens on hinged lower of D2, virtually any PTZ or Mini-Dome Camera can be mounted into the enclosure at any level.
14
Installing Camera Bracket 3. The 2.25" standoffs will be inserted on the upper portion of the D2. Axis 214 PTZ Required components (see component checklist): Part # 1,3,5,12,14,15,& 16 Picture represents standoff location & orientation. Height of standoffs will vary depending on camera used. 4. Now slide the camera bracket with the camera into place to line up with 4 screws holes from the standoffs. 5. Use (4) #8-32 screws (Phillips head) to secure the bracket into place.
16
Installing Camera Bracket Axis 233D PTZ Align these 2 holes with the D2 bracket holes for the Axis 233D Required components (see component checklist): Part # 1,2,3,9,10,11,& 12 Axis 233D Ceiling bracket that came with the camera. *This is a required item for installation* 2. Do this by aligning the two holes on the D2 camera bracket with the Axis ceiling bracket adapter.
Installing Camera Bracket Axis 233D PTZ Continued . . . . . . . . 6. Now slide the camera bracket with the camera into place to line up with 4 screws holes from the standoffs. 7. Use (4) #8-32 screws (Phillips head) to secure the bracket into place. Picture represents standoff location & camera bracket orientation. Height of standoffs will vary depending on camera used. Tip: Insert (2) #8-32 screws in the front two standoffs to provide a guide to slide the camera bracket into.
Installing Camera Bracket 3. The 2" standoffs will be inserted on the lower lens portion of the D2. Canon VB-C300 Required components (see component checklist): Part# 1,2,3,5,6,7,& 8 Picture represents standoff location & orientation. Height of standoffs will vary depending on camera used. 4. Now slide the camera bracket with the camera into place to line up with 4 screws from the standoffs. This edge nests in arch at front of D2 5. Secure the plate by using (4) .
Installing Camera Bracket 3. The 2.5" standoffs will be inserted on the lower lens portion of the D2. Panasonic NS-202 Required components (see component checklist): Part# 1,2,4,5,6,7,& 8 Picture represents standoff location & orientation. Height of standoffs will vary depending on camera used. 4. Now slide the camera bracket with the camera into place to line up with 4 screws from the standoffs. This edge nests in arch at front of D2 5. Secure the plate by using (4) .
Installing Camera Bracket 3. The 2.0" standoffs will be inserted on the lower lens portion of the D2. Panasonic BB-HCM381/ 580/581 & KX-HMC280 Required components (see component checklist): Part# 1,2,3,5,6,7,& 8 Picture represents standoff location & orientation. Height of standoffs will vary depending on camera used. 4. Now slide the camera bracket with the camera into place to line up with 4 screws from the standoffs. This edge nests in arch at front of D2 5. Secure the plate by using (4) .
Installing Camera Bracket 2. The Sony RZ25N camera requires a 1.25" spacing for optimal fit and operation. Use (1) .75" standoffs and (1) .5" standoffs that are provided to create a 1.25" standoff. You will need to create 4 of these with the included hardware. Sony RZ25N Required components (see component checklist): Part # 1,2,3,12,14,15,& 16 .75' .5" 3. The 1.25" standoffs will be inserted on the upper portion of the D2. Picture represents standoff location & orientation.
Installing Camera Bracket 3. The 2.5" standoffs will be inserted on the upper portion of the D2. Sony RZ50N Required components (see component checklist): Part # 1,4,5,6,7,8,& 12 Picture represents standoff location & orientation. Height of standoffs will vary depending on camera used. 4. Now slide the camera bracket with the camera into place to line up with 4 screws holes from the standoffs. 5. Use (4) #8-32 screws (Phillips head) to secure the bracket into place.
Installing Camera Bracket 3. The .5" standoffs will be inserted on the upper portion of the D2. Sony RX550N Required components (see component checklist): Part # 1,2,12,14,15, & 16 Picture represents standoff location & orientation. Height of standoffs will vary depending on camera used. 4. Now slide the camera bracket with the camera into place to line up with 4 screws holes from the standoffs. 5. Use (4) #8-32 screws (Phillips head) to secure the bracket into place.
Installing Camera Bracket Toshiba WB21A Required components (see component checklist): Part # 1,2,3,4,5,6,14,15,16,& 17 Align these 4 holes with the D2 bracket holes for the Toshiba WB21A 2. Do this by aligning the four holes on the D2 camera bracket with the Toshiba ceiling bracket adapter. Use (4) m3-.5 ½” long screws, (4) m3 external lock washer, (4) m3 1/8" washers, and (4) m3 lock nuts that are included to secure the toshiba ceiling adapter to the D2 camera bracket.
Installing Camera Bracket Toshiba WB21A Continued . . . . . . . . 5. The 2.75" standoffs will be inserted on the lower portion of the D2. Picture represents standoff location & orientation. Height of standoffs will vary depending on camera used. 6. Now slide the camera bracket with the camera into place to line up with 4 screws from the standoffs. 7. Secure the plate by using (4) 1.0" standoffs to lock the bracket in place. The two front location will require the use of (2) .25" washer. See picture.
Optional Steady Step Mounting System Steady Step Bracket Steps adjust in ¼” increments. To adjust 1/8” between step settings, add 1/8” brass male-male hex stand-off (ITEM NO. 6) shown in detail D, by threading on top of movable slide bracket, then fastening camera bracket (CB-1007 or AB-1007).
D2 Exploded Detail 28
D2 Mounting Detail 29
