MULTI-INNO TECHNOLOGY CO., LTD. LCD MODULE SPECIFICATION Model : MI12864J-G-1 Revision Engineering Date Our Reference Address Tel Fax Email Web : Room 10J,Xin HaoFang Building, No.188 Shennan Road, Nanshan Drstrict, ShenZhen,China. : (86-755)2643 9937 : (86-755)8613 4241 : sales@multi-inno.com : http://www.multi-inno.com 1.
Ver 1.0 MODULE NO.: MI12864J-G-1 REVISION RECORD REV NO. 1.0 REV DATE 2011-4-15 CONTENTS First release MULTI-INNO TECHNOLOGY CO.,LTD. REMARKS \ P.
MODULE NO.: MI12864J-G-1 Ver 1.0 CONTENTS GENERAL INFORMATION EXTERNAL DIMENSIONS ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS TIMING OF POWER SUPPLY BACKLIGHT CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS INTERFACE DESCRIPTION REFERENCE APPLICATION CIRCUIT REFERENCE INITIAL CODE RELIABILITY TEST INSPECTION CRITERION PRECAUTIONS FOR USING LCD MODULES PRIOR CONSULT MATTER MULTI-INNO TECHNOLOGY CO.,LTD. P.
MODULE NO.: MI12864J-G-1 Ver 1.0 GENERAL INFORMATION Item of general information LCD type Recommended Viewing Direction Module area (W × H×T) Viewing area (W×H) Active area (W×H) Number of Dots Pixel pitch (W × H) Driver IC Interface Type Input voltage Module Power consumption Backlight Type MULTI-INNO TECHNOLOGY CO.,LTD. Contents Unit FSTN /B/W MODE POSITIVE/TRANSFLECTIVE 6 00 70.00×43.00×9.00 59.00×30.50 55.00×27.48 128×64 0.39×0.
NC NC SCAN "A" 128X64 DOTS LED BACKLIGHT "B" K A K A CONTACT SIDE UV tape BLACK SILICONE - FPC BLACK SILICONE STIFFENER DETAL"A"/SCALE10X DETAL"B"/SCALE 10X P.5 MULTI-INNO TECHNOLOGY CO.,LTD. Ver 1.0 MODULE NO.
Ver 1.0 MODULE NO.: MI12864J-G-1 ABSOLUTE MAXIMUM RATINGS Parameter of absolute maximum ratings Supply voltage for logic Input voltage Operating temperature Storage temperature Humidity Symbol VDD VIN Top TST RH Min -0.3 -0.3 -20 -30 - Max Unit 4.0 VDD+0.
Ver 1.0 MODULE NO.: MI12864J-G-1 ELECTRO-OPTICAL CHARACTERISTICS Item of electro-optical characteristics Response time Contrast ratio Luminance uniformity Surface Luminance Symbol Tr+ Tf Cr δ WHITE Condition θ=0° ∅=0° Ta=25 Lv Viewing angle θ range ∅ = 90° ∅ = 270° ∅ = 0° ∅ = 180° Min Typ Max Unit Remark Note 3 418 6 627 - ms --- Fig.1 FIG 2. 4 1 67 74 - % FIG 2. 3 73 91 - cd/m2 FIG 2. 2 41 70 42 49 51 80 52 59 - deg deg deg deg 6 FIG 3. FIG 3. FIG 3. FIG 3. Note1.
MODULE NO.: MI12864J-G-1 FIG.1. Ver 1.0 The definition of Response Time FIG.2. Measuring method for Contrast ratio,surface luminance, Luminance uniformity,CIE (x, y) chromaticity A : 5 mm B : 5 mm H,V : Active Area Light spot size ∅=5mm, 500mm distance from the LCD surface to detector lens measurement instrument is TOPCON’s luminance meter BM-5 FIG.3. The definition of viewing angle MULTI-INNO TECHNOLOGY CO.,LTD. P.
Ver 1.0 MODULE NO.: MI12864J-G-1 INTERFACE DESCRIPTION Pin No. I/O or connect to Symbol 1 2 3 4 5 6 NC V0 V4 V3 V2 V1 - 7 C2- - 8 C2+ - 9 C1+ - 10 C1- - 11 C3+ - 12 13 14 15 16 VOUT VSS VDD SI SCL 0V 3.0V H/L H/L 17 RS H/L 18 /RES H/L 19 20 /CS1 NC H/L - When not in use Description No connection LCD driver supply voltages. LCD driver supply voltages. LCD driver supply voltages. LCD driver supply voltages. LCD driver supply voltages.
MODULE NO.: MI12864J-G-1 Ver 1.0 RELIABILITY TEST CONDITIONS No. Test Item Test Condition Inspection after test 1 2 3 4 High Temperature Storage Low Temperature Storage High Temperature Operating Low Temperature Operating 5 Temperature Cycle storage 6 Damp proof Test operating 7 Vibration Test 8 Dropping test 80 2 /200 hours -30 2 /200 hours 70 2 /120 hours -20 2 /120 hours -20 2 ~25~70 2 10cycles (30min.) (5min.) (30min.) 50 5 90%RH/120 hours Frequency 10Hz~55Hz~10Hz Amplitude 1.
MODULE NO.: MI12864J-G-1 Ver 1.0 INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Normal LCM Product. 1 Sample plan Sampling plan according to GB/T2828.1-2003/ISO 2859-1 1999 and ANSI/ASQC Z1.4-1993, normal level 2 and based on: Major defect: AQL 0.65 Minor defect: AQL 1.5 2.
Ver 1.0 MODULE NO.: MI12864J-G-1 4.Inspection Standard 4.1 Major Defect Item No Items to be inspected 4.1.1 All functional defects 4.1.2 4.1.3 Classification of defects Inspection Standard 1) No display 2) Display abnormally 3) Missing vertical horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. Major Missing Missing component Outline dimension Overall outline dimension beyond the drawing is not allowed. 4.2 Cosmetic Defect 4.2.
MODULE NO.: MI12864J-G-1 9 Solder splash ball/Solder a. The spacing between solder ball and h the conductor or solder pad h ≥0.13mm. d The diameter of solder ball d ≤0.15mm. h b. The quantity of solder balls or solder Splashes isn’t beyond 5 in 600 mm 2 . c. Solder balls/Solder splashes do not violate minimum electrical clearance. d. Solder balls/Solder splashes must be entrapped/encapsulated Or attached to the metal surface . Ver 1.
Ver 1.0 MODULE NO.: MI12864J-G-1 4.2.3 Cosmetic Criteria (Operating) No. Defect 1 Spots Judgment Criterion Partition Minor A) Clear Lcd Size : d mm d≤0.1 0.1 d≤0.2 0.2 d≤0.3 0.3 < d d ≤0.1 0.1 d≤0.3 0.3 d≤0.5 0.5 < d size Lcd size 8.0' Lcd size 8.0' Acceptable Qty in active area Disregard 6 2 0 Disregard 10 5 0 Note : Including pin holes and defective dots which must be within one pixel size; Total defective point shall not exceed 6 pcs no more than 8 inch LCD and 10PCS for more than 8 inch LCD.
MODULE NO.: MI12864J-G-1 Ver 1.0 3 Rubbing line Not to be noticeable. Minor 4 Allowable density Above defects should be separated more than 10mm each other. Minor 5 Rainbow Not to be noticeable. Minor 6 Dot size To be 95% ∼ 105% of the dot size (Typ.) in drawing. Partial defects of each dot (ex. pin-hole) should be treated as ‘Spot’. (see Screen Cosmetic Criteria (Operating) No.1) Minor 7 Uneven brightness Uneven brightness must be BMAX / BMIN ≤ 2 (only back-lit type - BMAX : Max.
MODULE NO.: MI12864J-G-1 Ver 1.0 PRECAUTIONS FOR USING LCD MODULES 1 Handing Precautions 1.1 The display panel is made of glass and polarizer. As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do not subject it to a mechanical shock by dropping it or impact. 1.2 If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth.
MODULE NO.: MI12864J-G-1 Ver 1.0 and other work under dry conditions. To reduce the generation of static electricity be careful that the air in the work is not too dry. A relative humidity of 50%-60% is recommended. As far as possible make the electric potential of your work clothes and that of the work bench the ground potential. - The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated. 1.
MODULE NO.: MI12864J-G-1 2 Ver 1.0 Handling precaution for LCM 2.1 LCM is easy to be damaged. Please note below and be careful for handling. 2.2 Correct handling: As above picture, please handle with anti-static gloves around LCM edges. 2.3 Incorrect handling: Please don’t stack LCM. Please don’t touch IC directly. Please don’t hold the surface of panel. Please don’t hold the surface of IC. MULTI-INNO TECHNOLOGY CO.,LTD. Please don’t stretch interface of output, such as FPC cable.
MODULE NO.: MI12864J-G-1 3 Storage Precautions 3.1 When storing the LCD modules, the following precaution are necessary. 3.1.1 Store them in a sealed polyethylene bag. If properly sealed, there is no need for the desiccant. 3.1.2 Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0°C and 35°C, and keep the relative humidity between 40%RH and 60%RH. 3.1.
MODULE NO.: MI12864J-G-1 4.2 Ver 1.0 Precaution for assemble the module with BTB connector: Please note the position of the male and female connector position, don’t assemble or assemble like the method which the following picture shows MULTI-INNO TECHNOLOGY CO.,LTD. P.
MODULE NO.: MI12864J-G-1 4.3 Ver 1.0 Precaution for soldering the LCM No RoHS Product RoHS Product Manual soldering 290°C ~350°C. Time : 3-5S. Machine drag soldering 330°C ~350°C. Speed : 15-17 mm/s. 340°C ~370°C. Time : 3-5S. 350°C ~370°C. Speed : 15-17 mm/s. Machine press soldering 300°C ~330°C. Time : 3-6S. Press: 0.8~1.2Mpa 330°C ~360°C. Time : 3-6S. Press: 0.8~1.2Mpa 4.3.
MODULE NO.: MI12864J-G-1 Ver 1.0 4.6 Limited Warranty Unless agreed between Multi-Inno and the customer, Multi-Inno will replace or repair any of its LCD modules which are found to be functionally defective when inspected in accordance with Multi-Inno LCD acceptance standards (copies available upon request) for a period of one year from date of production. Cosmetic/visual defects must be returned to Multi-Inno within 90 days of shipment.
