Instruction manual

ManualsBrandsAxis ManualsComputer equipmentNPS 532

www.Fisher.com

Fisherr V150S Slurry Vee-Ball™ Control Valve

NPS 3 through 12

Contents

Introduction 1.................................

Scope of Manual 1.............................

Specification table 2...........................

Description 2.................................

Installation 3

....................................

Maintenance 6..................................

Packing Maintenance 6........................

Disassembly 6............................

Assembly 8...............................

Actuator Mounting 9

.............................

Determining Mounting Position

for Spline Shaft/Lever Type 10

.................

Determining Closed Position 10.................

Parts Ordering 13

................................

Parts List 13.....................................

Figure 1. Fisher V150S Slurry Vee-Ball Control Valve

W8512

Introduction

Scope of Manual

This instruction manual provides installation, operation, maintenance, and parts information for Fisher Vee-Ball V150S

(NPS 3 through 12) rotary control valves (see figure 1).

Refer to separate manuals for information concerning the actuator, positioner and accessories.

Do not install, operate, or maintain V150S valves without being fully trained and qualified in valve, actuator, and

accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important t o

carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings. If you

have any questions about these instructions, contact your Emerson Process Management sales office before

proceeding.

Description

The V150S Slurry Vee-Ball valve shown in figure 1 mates with CL150 raised face flanges. Rugged construction, highly

wear-resistant trim materials, and an unrestricted straight through flow path make the design ideal for controlling the

most abrasive of slurries.

A shaft with a choice of drive connections will allow a variety of power operated actuators and valve positioners or

controllers to be used.

The design is particularly effective in minimizing erosive damage to the adjoining pipework, thereby providing greater

operational safety and service life when compared with other valve types.

Instruction Manual

D103164X012

V150S Slurry Vee-Ball Valve

May 2012

Summary of content (16 pages)

PAGE 1
Instruction Manual V150S Slurry Vee-Ball Valve D103164X012 May 2012 Fisherr V150S Slurry Vee-Ball™ Control Valve NPS 3 through 12 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specification table . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
Instruction Manual V150S Slurry Vee-Ball Valve May 2012 D103164X012 Table 1. Specifications Valve Sizes and End Connection Styles NPS J 3, J 4, J 6, J 8, J 10, and J 12 with CL150 raised-face flanges Shutoff Classification Construction does not provide tight shutoff. Nominal gap between ball and flow ring seat is 0.035 inch for high chrome iron construction and 0.015 inch for ceramic insert construction.
PAGE 3
Instruction Manual V150S Slurry Vee-Ball Valve D103164X012 May 2012 Figure 2. Flange Stud Length for Seal Protector End DIMENSION SHOWN IN TABLE 3 FIRST FULL THREAD TO FIRST FULL THREAD 1A4520 Table 3. Flange Stud Lengths Required for Flow Ring End of Fisher V150S Valves V150S VALVE SIZE, NPS mm Inches 3 4 6 8 10 12 95 108 114 183 222 256 3.75 4.25 4.50 7.19 8.72 10.10 Specifications Specifications for these valves are shown in table 1 and in bulletin 51.3:V150S.
PAGE 4
Instruction Manual V150S Slurry Vee-Ball Valve May 2012 D103164X012 Check with your process or safety engineer for any additional measures that must be taken to protect against process media. If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this instruction manual.
PAGE 5
Instruction Manual V150S Slurry Vee-Ball Valve D103164X012 May 2012 Table 4. Fisher V150S Dimensions V150S DIMENSIONS(1) VALVE SIZE A B D G K DN M(2) N(2) S Diameter T U W mm 80 165 80.0 235 140 130 104 98.0 19.1 152 31.8 14.2 100 194 102 214 152 140 117 98.0 19.1 152 31.8 14.2 150 230 111 214 175 164 124 112 25.4 152 31.8 14.2 200 304 184 208 220 231 195 124 31.8 235 46.0 17.5 250 385 235 208 250 261 235 132 31.8 235 46.0 17.
PAGE 6
V150S Slurry Vee-Ball Valve May 2012 Instruction Manual D103164X012 Maintenance WARNING The V-notch ball closes with a shearing, cutting motion, which could result in personal injury. To avoid injury, keep hands, tools, and other objects away from the V-notch ball while stroking the valve. Avoid personal injury from sudden release of process pressure. Before performing any maintenance operations: D Do not remove the actuator from the valve while the valve is still pressurized.
PAGE 7
Instruction Manual V150S Slurry Vee-Ball Valve D103164X012 May 2012 Figure 6. Packing Arrangements PACKING FOLLOWER (KEY 16) PACKING FOLLOWER (KEY 16) PACKING SET (KEY 15) PACKING SET (KEY 15) 1 PACKING BOX RING (KEY 14) PTFE V-RING PACKING FOR V150S NOTE: INCLUDES ZINC WASHERS FOR 1 GRAPHITE RIBBON PACKING ONLY. PACKING BOX RING (KEY 14) GRAPHITE RIBBON PACKING FOR V150S STANDARD PACKING 28B5170 CAUTION Trim parts are made from brittle material, handle with care to avoid chipping or breakage.
PAGE 8
V150S Slurry Vee-Ball Valve Instruction Manual May 2012 D103164X012 For service applications involving scale formation that sets up and “freezes” mating parts, supplementary recommendations for disassembly can be provided by your Emerson Process Management sales office. Assembly WARNING Observe the steps in the WARNING at the beginning of the Maintenance section. Reference figures 9 and 10. CAUTION Trim parts are made from brittle material, handle with care to avoid chipping or breakage. 1.
PAGE 9
Instruction Manual V150S Slurry Vee-Ball Valve D103164X012 May 2012 11. Fit the spring (key 19), gasket (key 21), and plug (key 20). For service applications involving scale formation that sets up and “freezes” mating parts, supplementary recommendations for assembly can be provided by your Emerson Process Management sales office.
PAGE 10
Instruction Manual V150S Slurry Vee-Ball Valve May 2012 D103164X012 Figure 8. Index Marks for Actuator Lever Orientation for NPS 3 through 12 Valves ACTUATOR MOUNTING STYLE VALVE OPEN ACTUATOR POSITION 1 2 3 4 STYLE D PUSH DOWN TO CLOSE (OPTIONAL) LEFT-HAND BALL ROTATES COUNTERCLOCKWISE TO CLOSE FLOW STYLE C PUSH DOWN TO OPEN FLOW STYLE B PUSH DOWN TO CLOSE (STANDARD) RIGHT-HAND BALL ROTATES CLOCKWISE TO CLOSE FLOW STYLE A PUSH DOWN TO OPEN FLOW NOTE: 1.
PAGE 11
Instruction Manual V150S Slurry Vee-Ball Valve D103164X012 May 2012 Figure 9.
PAGE 12
V150S Slurry Vee-Ball Valve May 2012 Figure 10.
PAGE 13
Instruction Manual V150S Slurry Vee-Ball Valve D103164X012 May 2012 Parts Ordering A serial number is assigned to each valve and stamped on the nameplate. Always refer to the valve serial number when corresponding with your Emerson Process Management sales office regarding spare parts or technical information. When ordering replacement parts, also specify the complete 11-character part number from the parts kits or parts list information. WARNING Use only genuine Fisher replacement parts.
PAGE 14
Instruction Manual V150S Slurry Vee-Ball Valve May 2012 Key 8 8 9 10* 13* 14* 15* 16 17 18 14 Description Drive Shaft Spline Drive Shaft, DD Follower Shaft Shaft Pin, carbon steel, zinc plated (2 req'd) NPS 3 NPS 4 NPS 6 NPS 8 NPS 10 NPS 12 Gasket, graphite/laminate NPS 3 NPS 4 NPS 6 NPS 8 NPS 10 NPS 12 Packing Box Ring, 316 SST NPS 3 and 4 NPS 6 NPS 8 NPS 10 NPS 12 Packing Set PTFE NPS 3 and 4 NPS 6 NPS 8 NPS 10 NPS 12 Graphite/laminate NPS 3 and 4 NPS 6 NPS 8 NPS 10 NPS 12 Packing Follower Stud, 2
PAGE 15
Instruction Manual D103164X012 V150S Slurry Vee-Ball Valve May 2012 15
PAGE 16
V150S Slurry Vee-Ball Valve May 2012 Instruction Manual D103164X012 Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. Fisher and Vee-Ball are marks owned by one of the companies in the Emerson Process Management business unit of Emerson Electric Co.