AXIS P1365-E Network Camera User Manual
About this Document This manual is intended for administrators and users of AXIS P1365-E Fixed Dome Network Camera, and is applicable to firmware 5.75 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be useful when developing shell scripts and applications. Later versions of this document will be posted at www.axis.com.
The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) according to IEC/EN/UL 60950-1. Battery Low battery power affects the operation of the RTC, causing it to reset at every power-up. When the battery needs replacing, a log message will appear in the product’s server report. For more information about the server report, see the product´s setup pages or contact Axis support.
AXIS P1365-E Network Camera Safety Information Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE TICE NO Indicates a situation which, if not avoided, could result in damage to property.
AXIS P1365-E Network Camera Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . . . . . .
AXIS P1365-E Network Camera Table of Contents Continuous Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS P1365-E Network Camera Hardware Overview Hardware Overview 1 2 3 4 5 6 7 8 9 10 14 11 15 12 16 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Status LED Focus ring Lock screw for focus ring Zoom puller Built-in microphone microSD card slot Audio in Audio out Network connector (PoE) Power LED Network LED Control button I/O connector Iris connector Power connector (not used) RS485/422 connector 7
AXIS P1365-E Network Camera Hardware Overview 1 2 3 4 5 6 7 15 14 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 12 11 10 9 8 Safety wire Heater connector Network connector (PoE OUT) Status LED indicator Network connector (PoE IN) Heater cable Cable gasket M20 (2x) Drill-out (2x) Slot for intrusion alarm switch – supports AXIS Door Switch A (sold separately) Holder screw T20 (2x) Camera screw T20 Pin Holder Window Top cover Connectors and Buttons For technical specifications, see page 68.
AXIS P1365-E Network Camera Hardware Overview Audio Connector The Axis product has the following audio connectors: • Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal. • Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for audio out. For audio in, the left channel is used from a stereo signal.
AXIS P1365-E Network Camera Hardware Overview Power LED Indication Green Normal operation. Amber Flashes green/amber during firmware upgrade. Status LED Behavior for Focus Assistant Color Indication Green Focus Assistant is enabled The lens is optimally adjusted Amber The camera has been moved, or an object has been placed in front of the lens. Exit and restart the Focus Assistant. The lens is less optimally adjusted.
AXIS P1365-E Network Camera Hardware Overview 6. Click Upload. The installed iris lens should now be included in the Iris Selection drop-down list. 7. Select the installed iris lens from the drop-down list and click OK.
AXIS P1365-E Network Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer® with Windows® • Safari® with OS X® • ChromeTM or Firefox® with other operating systems. See Technical Specifications on page 68. To view streaming video in Internet Explorer, allow installation of AXIS Media Control (AMC) when prompted.
AXIS P1365-E Network Camera Access the Product For Technical notes on this and other topics, visit the Axis Support web at www.axis.com/techsup Set the Root Password To access the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which opens when the product is accessed for the first time. To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate.
AXIS P1365-E Network Camera Access the Product The Live View Page The controls and layout of the Live View page may have been customized to meet specific installation requirements and user preferences. Consequently, some of the examples and functions featured here may differ from those displayed in your own Live View page. The following provides an overview of each available control. Controls on the Live View Page Click View size to scale the image down to 800 pixels wide or to full scale.
AXIS P1365-E Network Camera Access the Product To show the manual trigger buttons in the Live View page: 1. Go to Setup > Live View Config. 2. Under Action Buttons, select Show manual trigger button. AXIS Media Control viewer toolbar The AXIS Media Control viewer toolbar is available in Internet Explorer only. See AXIS Media Control (AMC) on page 17 for more information. The toolbar displays the following buttons: The Play button connects to the Axis product and starts playing a media stream.
AXIS P1365-E Network Camera Access the Product Click the Emulate joystick mode button and click in the image to move the camera view in the direction of the mouse pointer. Click the Center mode button and click in the image to center the camera view on that position. The center mode button could also be used to zoom in on a specific area. Click in the image and drag to draw a rectangle surrounding the area to be magnified. To zoom out, rotate the mouse wheel.
AXIS P1365-E Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.264 H.
AXIS P1365-E Network Camera Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start screen or Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS P1365-E Network Camera Media Streams Note • = IP address • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS P1365-E Network Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have restricted access to settings, see Users on page 51 See also the online help .
AXIS P1365-E Network Camera Set Up the Product Focus Assistant To focus using the Focus Assistant, follow the instructions in steps 1–3 on page 20 before you start with the steps below. Note • The view in front of the camera should not be changed during focus adjustment (steps 5 and 6). If the camera is moved, or if a finger or other object is placed in front of the lens, steps 3–7 below will have to be repeated.
AXIS P1365-E Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 22. • Stream profiles. See page 24. • Camera settings. See page 24. • View areas. See page 27. • Overlay image. See page 27. • Privacy mask. See page 29. • Focus. See page 30. • Audio settings. See page 30. • Audio clips. See page 32.
AXIS P1365-E Network Camera Video and Audio • Compression. The compression level affects the image quality, bandwidth and file size of saved images; the lower the compression, the higher the image quality with higher bandwidth requirements and larger file sizes. • Mirror image. If required, the image can be mirrored. • Rotate image. If required, the image can be rotated. • Maximum frame rate. To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a fixed amount.
AXIS P1365-E Network Camera Video and Audio These Zipstream strength options are available: • Off. Zipstream disabled. • Lowest Zipstream strength. Low bandwidth reduction. No visible quality degradation in most scenes • Medium Zipstream strength. Medium bandwidth reduction. Limited visual quality degradation in not prioritized areas in some scenes • Highest Zipstream strength. High bandwidth reduction.
AXIS P1365-E Network Camera Video and Audio Capture mode is set the first time the product is accessed. Select the desired capture mode and click OK. Important Changing capture mode when the product has been configured is not recommended as most other settings will be either removed or reset. To change capture mode, follow these steps: 1. Go to Setup > Video & Audio > Camera Settings. 2. Select the new capture mode. 3. Click Save.
AXIS P1365-E Network Camera Video and Audio Exposure control - This setting is used to adapt to the amount of light used. Automatic is the default setting and can be used in most situations. The shutter speed is automatically set to produce optimum image quality. Flicker-free 50 or 60 Hz is used to remove flicker which can be caused by fluorescent and other light sources. The Hold current option locks the current exposure settings.
AXIS P1365-E Network Camera Video and Audio change, the iris will adjust itself to the best iris settings. If automatic iris adjustment is disabled, the iris will lock on the set position regardless of light conditions Day/Night The IR cut filter prevents infrared (IR) light from reaching the image sensor. In poor lighting conditions, for example at night, or when using an external IR lamp, set the IR cut filter to Off. This increases light sensitivity and allows the product to “see” infrared light.
AXIS P1365-E Network Camera Video and Audio When using a text string, modifiers can be used to display information such as the current bit rate or the current frame rate. For information about available modifiers, see File Naming & Date/Time Formats in the online help . It is also possible to display text when an action rule is triggered, see Use Overlay Text in an Action Rule. Note To enable overlays: 1. Go to Video & Audio > Video Stream and select the Image tab. 2.
AXIS P1365-E Network Camera Video and Audio To select the image to use as overlay: 1. Go to Video & Audio > Overlay Image. 2. Select the image to use from the Use overlay image list and click Save. To display the overlay image: 1. Go to Video & Audio > Video Stream and select the Image tab. 2. Under Overlay Settings, select Include overlay image at the coordinates. 3. To control the image’s position, enter the X and Y coordinates. The X=0 and Y=0 position is the top left corner.
AXIS P1365-E Network Camera Video and Audio You can add a new mask, re-size the mask with the mouse, choose a color for the mask, and give the mask a name. For more information, see the online help Important Adding many privacy masks may affect the product’s performance. Focus You can focus the Axis product under Video & Audio > Focus. For most applications, the adjustments on the Basic tab are sufficient. If required, additional adjustments can be made on the Advanced tab.
AXIS P1365-E Network Camera Video and Audio If you have enabled view areas, remember that each view area is a separate video stream. To include the audio stream in all view areas, go to the audio tab in each video stream page and enable audio. For more information see View Area on page 27. Audio Modes The Axis product supports the following audio modes: • Full duplex – Simultaneous two-way audio allowing the Axis product to transmit and receive audio at the same time.
AXIS P1365-E Network Camera Video and Audio • G726 is an unlicensed speech codec that is most commonly used within the security industry. The Sample rate defines the number of times per second the sound is sampled. A higher sample rate will provide better audio quality, but also requires a greater bandwidth. Set the required Bit rate depending on the selected encoding. A higher bit rate will give better audio quality. A lower bit rate may have latency or delay, but will require less bandwidth.
AXIS P1365-E Network Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 24. • Default Viewer for Browser. See page 33. • Viewer Settings. See page 33. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 14. • User Defined Links. See page 34. • Output Buttons. See page 34.
AXIS P1365-E Network Camera Configure the Live View Page User Defined Links To display user-defined links in the Live View page, select the Show custom link option, give the link a name and then enter the URL to link to. When defining a web link do not remove the 'http://' from the URL address. Custom links can be used to run scripts or activate external devices connected to the product, or they can link to a web page.
AXIS P1365-E Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area or if a PTZ driver has been uploaded. For more information on view areas, see View Area on page 27. For more information on how to upload a driver, see Install PTZ Driver on page 37.
AXIS P1365-E Network Camera PTZ (Pan Tilt Zoom) When the focus window is set from the Preset Positions page, it will be included in the settings for that preset. The focus window can be redefined for the preset, but it cannot be deleted unless the preset is deleted. Guard Tour A guard tour displays the video stream from different preset positions, one-by-one, in a predetermined order or at random and for configurable time periods.
AXIS P1365-E Network Camera PTZ (Pan Tilt Zoom) Install PTZ Driver This Axis product supports several PTZ devices. Please see www.axis.com for a complete list of supported devices, and to obtain the correct driver. To install a PTZ device you need to install the PTZ driver. To install the PTZ driver go to PTZ> Driver Selection. Browse to find the driver (e.g. driver.ptz) and Upload. If the driver was successfully uploaded, it appears in the Select driver to use drop-down list.
AXIS P1365-E Network Camera Detectors Detectors Camera Tampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, spray-painted or severely defocused. To send an alarm, for example an email, an action rule must be set up. To configure tampering detection: 1. Go to Detectors > Camera Tampering. 2. Set the Minimum duration, that is, the time that must elapse before an alarm is generated.
AXIS P1365-E Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window. Set Up Motion Detection Windows To set up a motion detection Include Window, follow these instructions: 1. Go to Detectors > Motion Detection. 2.
AXIS P1365-E Network Camera Detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window, and select a low object size. • To avoid triggering on small objects, select a high object size. • While monitoring an area where moving objects are not expected, select a high history level. This will cause motion detection to trigger as long as the object is present in the window. • To only detect flashing light, select a low sensitivity.
AXIS P1365-E Network Camera Applications Applications AXIS Camera Application Platform (ACAP) is an open platform that enables third parties to develop analytics and other applications for Axis products. For information about available applications, downloads, trials and licenses, go to www.axis.com/applications Note • It is recommended to run one application at a time. • Avoid running applications when the built-in motion detection is active. Application Licenses Some applications need a license to run.
AXIS P1365-E Network Camera Applications If the Axis product is reset to factory default, uploaded applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings.
AXIS P1365-E Network Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS P1365-E Network Camera Events • - Day/Night Mode – Trigger the rule when the product switches between day mode (IR cut filter on) and night mode (IR cut filter off). This can for example be used to control an external infrared (IR) light connected to an output port. - Live Stream Accessed – Trigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notifications. - Motion Detection – Trigger the rule when motion is detected.
AXIS P1365-E Network Camera Events • Output Port – Activate an I/O port to control an external device. • Overlay Text – Display an overlay text. See Use Overlay Text in an Action Rule on page 29. • Play Audio Clip – See Audio Clips on page 32. • PTZ Control - Preset Position – Go to a preset position. - Guard Tour – Start a guard tour. See Guard Tour on page 36. • Record Video – Record video and audio to a selected storage.
AXIS P1365-E Network Camera Events HTTP Send Images Send Notification Send Video Clip Network Share A network share can also be used as a storage device for recorded video. Go System Options > Storage to configure a network share before setting up a continuous recording or an action rule to record video. For more information about storage devices, see Storage on page 59.
AXIS P1365-E Network Camera Events Set Up Recurrences Recurrences are used to trigger action rules repeatedly, for example every 5 minutes or every hour. To set up a recurrence: 1. Go to Events > Recurrences and click Add. 2. Enter a descriptive name and recurrence pattern. 3. Click OK. To use the recurrence in an action rule, first select Time from the Trigger drop-down list in the Action Rule Setup page and then select the recurrence from the second drop-down list.
AXIS P1365-E Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 49. • To set up action rules, see page 43. • To access recordings, see Find Recordings on page 48. • To play recordings, see Play Recording on page 48. • To export a recording as a video clip, see Export Video Clip on page 49. • To configure camera controlled storage, see Storage on page 59.
AXIS P1365-E Network Camera Recordings 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the filters. See also Find Recordings on page 48. 3. Select the recording and click Play. The recording will be played in a new browser window. Export Video Clip Note The exported recording is a Matroska video file (.mkv). To play the recording in Windows Media Player, AXIS Matroska File Splitter must be installed.
AXIS P1365-E Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS P1365-E Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS P1365-E Network Camera System Options HTTPS HTTPS (HyperText Transfer Protocol over Secure Socket Layer, or HTTP over SSL) is a web protocol providing encrypted browsing. HTTPS can also be used by users and clients to verify that the correct device is being accessed. The security level provided by HTTPS is considered adequate for most commercial exchanges. The Axis product can be configured to require HTTPS when users from different user groups (administrator, operator, viewer) log in.
AXIS P1365-E Network Camera System Options Certificates Certificates are used to authenticate devices on a network. Typical applications include encrypted web browsing (HTTPS), network protection via IEEE 802.1X and secure upload of images and notification messages for example via email. Two types of certificates can be used with the Axis product: Server/Client certificates - To authenticate the Axis product.
AXIS P1365-E Network Camera System Options • Synchronize with computer time – Sets date and time according to the computer’s clock. With this option, date and time are set once and will not be updated automatically. • Synchronize with NTP Server – Obtains date and time from an NTP server. With this option, date and time settings are updated continuously. For information on NTP settings, see NTP Configuration on page 56. If using a host name for the NTP server, a DNS server must be configured.
AXIS P1365-E Network Camera System Options 1. Acquire a free static IP address on the same network segment as the computer. 2. Locate the serial number (S/N) on the product label. 3. Open a command prompt and enter the following commands: Linux/Unix syntax arp -s temp ping -s 408 Linux/Unix example arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.
AXIS P1365-E Network Camera System Options To register the Axis product with AXIS Internet Dynamic DNS Service, go to System Options > Network > TCP/IP > Basic. Under Services, click the AXIS Internet Dynamic DNS Service Settings button (requires access to the Internet). The domain name currently registered at AXIS Internet Dynamic DNS service for the product can at any time be removed. Note AXIS Internet Dynamic DNS Service requires IPv4.
AXIS P1365-E Network Camera System Options HTTPS The HTTPS port used by the Axis product can be changed under System Options > Network > TCP/IP > Advanced. In addition to the default setting, which is 443, any port in the range 1024–65535 can be used. To enable HTTPS, go to System Options > Security > HTTPS. For more information, see HTTPS on page 52. NAT traversal (port mapping) for IPv4 A network router allows devices on a private network (LAN) to share a single connection to the Internet.
AXIS P1365-E Network Camera System Options SOCKS SOCKS is a networking proxy protocol. The Axis product can be configured to use a SOCKS server to reach networks on the other side of a firewall or proxy server. This functionality is useful if the Axis product is located on a local network behind a firewall, and notifications, uploads, alarms, etc need to be sent to a destination outside the local network (for example the Internet). SOCKS is configured under System Options > Network > SOCKS.
AXIS P1365-E Network Camera System Options Note The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 63. UPnPTM The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. UPnPTM can be disabled under System Options > Network > UPnP RTP/H.
AXIS P1365-E Network Camera System Options Mount and Unmount SD Card NOTICE TICE NO To prevent corruption of recordings, the SD card should always be unmounted before it is ejected. The SD card is automatically mounted when the card is inserted into the Axis product or when the product is started. A manual mount is only required if the card has been unmounted and not ejected and re-inserted. To unmount the SD card: 1. Open the Axis product’s webpages and go to Setup > System Options > Storage. 2.
AXIS P1365-E Network Camera System Options 6. Click Connect. To clear all recordings and data from the Axis product’s folder on the designated share, click Clear under Storage Tools. To avoid filling the share, it is recommended to remove recordings continuously. Under Recording Settings, select Remove recordings older than and select the number of days or weeks. To stop writing to the share and protect recordings from being removed, select Lock under Recording Settings.
AXIS P1365-E Network Camera System Options • the default router • the subnet mask • the system time • the IEEE 802.1X settings • the focus position • uploaded applications are kept but must be restarted Click Default to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The Axis product can also be reset to factory default using the control button, see Reset to Factory Default Settings on page 63.
AXIS P1365-E Network Camera System Options Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NOTICE TICE NO Improper use may cause unexpected behavior and loss of contact with the Axis product. Axis strongly recommends that you do not use this function unless you understand the consequences. Axis Support does not provide assistance for problems with customized scripts. To open the Script Editor, go to System Options > Advanced > Scripting.
AXIS P1365-E Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS P1365-E Network Camera Troubleshooting The IP address is being used by another device Disconnect the Axis product from the network. Run the Ping command (in a Command/DOS window, type ping and the IP address of the product): • If you receive: Reply from : bytes=32; time=10... this means that the IP address may already be in use by another device on the network. Obtain a new IP address from the network administrator and reinstall the product.
AXIS P1365-E Network Camera Troubleshooting Poor rendering of H.264 images Ensure that your graphics card is using the latest driver. The latest drivers can usually be downloaded from the manufacturer’s website. Color saturation is different in H.264 and Motion JPEG Modify the settings for your graphics adapter. Refer to the adapter’s documentation for more information. Lower frame rate than expected See Performance Considerations on page 71.
AXIS P1365-E Network Camera Troubleshooting Distorted audio Check that the correct Audio Input source is selected under Setup > Video & Audio > Audio Settings. Feedback loops Feedback loops might appear in full-duplex mode. Try moving the microphone or the speaker, or use half-duplex mode instead. Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur.
AXIS P1365-E Network Camera Technical Specifications Technical Specifications Camera Image sensor Progressive scan RGB CMOS 1/2.8” Lens Varifocal, 2.8–8 mm, F1.3, IR corrected, CS-mount, Megapixel resolution, P-Iris Horizontal angle of view: 90°–40° Vertical angle of view: 49.3°–22° Diagonal angle of view: 104.6°–6° Day and night Automatically removable infrared-cut filter Minimum illumination Color: 0.18 lux, B/W: 0.04 lux, F1.3 HDTV 1080p 50/60 fps: Color 0.36 lux, B/W: 0.08 lux, F1.
AXIS P1365-E Network Camera Technical Specifications Network Security Password protection, IP address filtering, HTTPSa encryption, IEEE 802.
AXIS P1365-E Network Camera Technical Specifications AXIS Door Switch A AXIS T98A16-VE Surveillance Cabinet Video management software AXIS Camera Companion (included), AXIS Camera Station and video management software from Axis’ Application Development Partners (not included). For more information, see www.axis.com/products/video/software Warranty Axis 3-year warranty and AXIS Extended Warranty option, see www.axis.com/warranty a.
AXIS P1365-E Network Camera Technical Specifications RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serial interface.
User Manual AXIS P1365-E Network Camera © Axis Communications AB, 2015 Ver. M2.3 Date: July 2015 Part No.
