INSTALLATION GUIDE AXIS P3346-VE Network Camera AXIS P3367-VE Network Camera AXIS P3384-VE Network Camera
Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license. To purchase further licenses, contact your reseller. Liability Every care has been taken in the preparation of this document. Please inform your local Axis office of any inaccuracies or omissions.
Japan - この装置は、クラスB 情報技術装置です。 この装置 は、家庭環境で使用することを目的として います が、この装置がラジオやテレビジョン受信機 に近 接して使用されると、受信障害を引き起こすこ と があります。取扱説明書に従って正しい取り扱い をして下さい。本製品は、シールドネットワーク ケーブル(STP)を使用して接続してください。また 適切に接地してください。 Korea - ࢇ ̛̛Е ɼࢽࡈ %̗ ࢷળࢶଢ̛̛Ի۰ ࣯Ի ɼࢽ߾۰ ࡈیଜЕ ʨࡶ ּࢶࡳԻ ଜֲ ֻҘ ए ࠇ߾۰ ࡈیଟ ܹ ݡТЬ ࢶࢸ ࢻएѹ 673 VKLHOGHG WZLVWHG SDLU ৼࢇࡈی ࡶٴଜࠆ ࢿ૽ ࡶ ࠉʼ ଜ ࠝݤݫ Safety This product complies with IEC/EN 60950-1, Safety of Information Technology Equipment.
AXIS P33-VE Series Installation Guide Page 5 Safety Information Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Page 6 AXIS P33-VE Series Installation Guide Safety Instructions • The Axis product shall be installed by a trained professional. • • • • • • • • • The Axis product shall be used in compliance with local laws and regulations. Store the Axis product in a dry and ventilated environment. Avoid exposing the Axis product to shocks or heavy pressure. Do not install the product on unstable brackets, surfaces or walls. Use only applicable tools when installing the Axis product.
AXIS P33-VE Series Installation Guide Page 7 Battery The Axis product uses a 3.0 V BR/CR2032 lithium battery as the power supply for its internal realtime clock (RTC). Under normal conditions this battery will last for a minimum of five years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. When the battery needs replacing, a log message will appear in the product’s server report.
Page 8 AXIS P33-VE Series Installation Guide Installation Guide This guide helps you to install the AXIS P33-VE Series on your network. For further information, please see the User Manual available on the CD, or from www.axis.com/techsup Follow these instructions to install the network camera 1. 2. 3. 4. 5. 6.
AXIS P33-VE Series Installation Guide Page 9 Package Contents Item Models/variants/notes Network camera with heating module AXIS P3346-VE AXIS P3367-VE AXIS P3384-VE Mounting bracket Dome covers Clear transparent cover Smoked transparent cover Weather shield Labels 2 adhesive serial no.
Page 10 AXIS P33-VE Series Installation Guide Hardware Overview Camera unit Heater I/O connector Network connector (PoE) Control button LED indicators Audio out Audio in Mounting bracket Unit casing Spring SD memory card slot Camera unit Dome cover Weather shield Holes for cables routed through the wall Serial no. Fan output Side holes with connector gaskets for cables routed along the wall The heater in the camera unit may be hot. Dimension (HxW) AXIS P3346-VE = 117 x 179 mm (4.59” x 7.
AXIS P33-VE Series Installation Guide Page 11 LED Indicators LED Color Indication Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity. Status Power Amber Steady for connection to 10 Mbit/s network. Flashes for network activity. Unlit No network connection. Green Steady green for normal operation. Amber Steady during startup; flashes once during reset to factory default or while restoring settings. Red Slow flash for failed upgrade.
Page 12 AXIS P33-VE Series Installation Guide Connectors Network Connector AXIS P3367-VE and AXIS AXIS P3384-VE: Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. All cables connecting the product to the network and that are routed outdoors or in demanding electrical environments shall be intended for their specific use.
AXIS P33-VE Series Installation Guide Page 13 I/O Connectors • • • I/O terminal connector - Used in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications. In addition to an auxiliary power and a GND pin, it provides the Pin4 Pin2 interface to: Pin3 Pin1 1 transistor output - For connecting external devices such as relays and LEDs.
Page 14 AXIS P33-VE Series Installation Guide The following connection diagram gives an example of how to connect an auxiliary device to the AXIS P3346-VE/P3367-VE/P3384-VE. 1 E.g. push button 3.3V max.
AXIS P33-VE Series Installation Guide Page 15 Install the Hardware Please remove the rubber band for transport-safety from the camera unit before you mount the camera. Prepare the Network Cable For network cable specifications, see Network Connector, on page 12. If a cable other than the provided cable is used, you need to prepare a network cable with a gasket. Gently force the cable through the gasket provided and attach a network connector.
Page 16 AXIS P33-VE Series Installation Guide Prepare the Unit Casing (routing cables along the wall) If the cables are to be routed along the wall, prepare the unit casing as follows: 1. Detach the side lid that is attached to the unit casing by removing the screw. 2. Loosen the two screws on the cable shield and detach the bottom part. 3. Attach the bottom part of the cable shield to the unit casing with the screw.
AXIS P33-VE Series Installation Guide Page 17 Route the Cables Depending on whether you want to route the cables through or along the wall, follow the relevant instructions below. Routing Cables along the Wall 1. Using the drill template drill 4 holes in the wall. 2. Attach the mounting bracket to the wall using the 4 screws provided, or screws appropriate for the wall material. 3. Remove the camera unit from the unit casing by pushing the springs aside. 4.
Page 18 AXIS P33-VE Series Installation Guide 8. Attach the unit casing to the mounting bracket by tightening the four screws.
AXIS P33-VE Series Installation Guide Page 19 Install the Camera Unit Connector for fan Camera unit Attach screw to camera Network cable 1. Attach the network cable to the camera unit; and the cable for audio and I/O if required. It is recommended that the network cable is twisted to a loop as shown in the illustration above. Be careful not to stretch or bend the network cable too much since this could cause damage to the network cable. 2. 3. 4. 5. Insert the SD memory card (optional).
Page 20 AXIS P33-VE Series Installation Guide The AXIS P3346-VE/P3367-VE/P3384-VE can also be fitted with a metal conduit for protecting the cabling when cables are routed along the wall.
AXIS P33-VE Series Installation Guide Page 21 Access the Product Use the tools provided on the Installation and Management Software CD to assign an IP address, set the password and access the video stream. This information is also available from the support pages on www.axis.com/techsup/ Adjust the Lens Adjusting the focus and zoom manually can damage the lens. Do not tilt the lens more than 90°, this may cause damage to the product. See the illustration below.
Page 22 AXIS P33-VE Series Installation Guide Open the Live View page in the web interface and make the following adjustments to the camera: Horizontal line Tilt adjustment screw Tilt adjustment screw Locking screw 1. Loosen the locking screw and tilt adjustment screws. 2. Turn the lens (with the lens holder) to the desired position. Make sure the horizontal lines on either side of the lens are aligned horizontally Ensure that the mark on the lens cover, between the horizontal lines, is facing up. 3.
AXIS P33-VE Series Installation Guide Page 23 Complete the Installation Black protective 1. Rotate the black protective shield inside the dome cover shield so it is aligned with the camera’s position. 2. If required, attach the weather shield to the camera before you attach the dome cover. To do this remove the two screws in the dome cover. Transfer the washers from these screws to the two long screws provided. Attach the weather shield using the two long screws. 3.
Page 24 AXIS P33-VE Series Installation Guide Reset to Factory Default Settings Reset to factory default should be used with caution. A reset to factory default will reset all settings, including the IP address, to the factory default values. The installation and management software tools are available on the CD supplied with the product and from the support pages on www.axis.com/techsup To reset all parameters and the IP address to Factory Default settings: 1. Disconnect the power from the product. 2.
Installation Guide AXIS P3346-VE/AXIS P3367-VE/AXIS P3384-VE © Axis Communications AB, 2014 Ver. 4.2 Printed: October 2014 Part No.
