AXIS P5635–E PTZ Dome Network Camera User Manual
About this Document This manual is intended for administrators and users of AXIS P5635–E PTZ Dome Network Camera, and is applicable to firmware 5.70 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be useful when developing shell scripts and applications. Later versions of this document will be posted at www.axis.com.
be connected using a shielded network cable (STP) that is properly grounded. Japan この装置は、クラスB 情報技術装置です。この装置は、家 庭環境で使用することを目 的としていますが、この装置が ラジオやテレビジョン受信機に近接して使用されると、 受 信障害を引き起こすことがあります。 取扱説明書に従って 正しい取り扱いをして下さい。 本製品は、シールドネット ワークケーブル(STP)を使用して接続してください。また 適切に接地してください。 Korea 이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에 서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. 적절히 접지된 STP (shielded twisted pair) 케이 블을 사용하여 제품을 연결 하십시오.
AXIS P5635–E PTZ Dome Network Camera Safety Information Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE TICE NO Indicates a situation which, if not avoided, could result in damage to property.
AXIS P5635–E PTZ Dome Network Camera Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . .
AXIS P5635–E PTZ Dome Network Camera Table of Contents Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset to Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repainting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting .
AXIS P5635–E PTZ Dome Network Camera Hardware Overview Hardware Overview 1 4 2 5 3 6 7 8 9 1 2 3 4 5 6 7 8 9 Ground screw Mounting screws (3) Network connector (PoE+) Multi-connector with cover (Do not remove the cover unless an I/O-cable is connected) Hook for safety wire SD memory card slot Control button Status LED indicator Power button Connectors and Buttons For technical specifications, see page 63. Network Connector RJ45 Ethernet connector with Power over Ethernet Plus (PoE+).
AXIS P5635–E PTZ Dome Network Camera Hardware Overview NOTICE TICE NO Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. All cables connecting the product to the network and that are routed outdoors or in demanding electrical environments shall be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions.
AXIS P5635–E PTZ Dome Network Camera Hardware Overview Amber Steady during startup. Flashes during firmware upgrade. Amber/Red Flashes amber/red if network connection is unavailable or lost.
AXIS P5635–E PTZ Dome Network Camera Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer® with Windows® • Safari® with OS X® and • ChromeTM or Firefox® with other operating systems. See Technical Specifications on page 63.
AXIS P5635–E PTZ Dome Network Camera Access the Product Set the Root Password To access the Axis product, you must set the password for the default administrator user root. This is done in the Configure Root Password dialog, which opens when the product is accessed for the first time. To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate.
AXIS P5635–E PTZ Dome Network Camera Access the Product The Audio clip drop-down list allows you to play an audio clip from the Live View page. Select the audio clip and click the Play button. Enable or disable the Gatekeeper by selecting On or Off from the drop-down list. For more information about the Gatekeeper, see page 29. Manual Trigger The Manual Trigger is used to trigger an action rule from the Live View page.
AXIS P5635–E PTZ Dome Network Camera Access the Product Speaker button — Click to turn the speakers on or off. Microphone button – Click to mute or unmute the microphone. In Simplex - speaker only mode, the Microphone and Talk buttons must both be active to send audio to the Axis product. Click either button to stop audio transmission. Use the slider to control the volume of the speakers and the microphone. Half-duplex mode The Talk/Listen button is used to switch between sending and receiving audio.
AXIS P5635–E PTZ Dome Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.264 H.
AXIS P5635–E PTZ Dome Network Camera Media Streams Alternative Methods of Accessing the Video Stream You can also access video and images from the Axis product in the following ways: • Motion JPEG server push (if supported by the client, Chrome or Firefox, for example). This option maintains an open HTTP connection to the browser and sends data as and when required, for as long as required. • Still JPEG images in a browser. Enter the path http:///axis-cgi/jpg/image.cgi • Windows Media Player.
AXIS P5635–E PTZ Dome Network Camera Media Streams • • • Windows Media Player supports simplex audio. The following paths can be used: - Unicast via RTP: axrtpu:///axis-media/media.amp - Unicast via RTSP: axrtsp:///axis-media/media.amp - Unicast via RTSP, tunneled via HTTP: axrtsphttp:///axis-media/media.amp - Multicast: axrtpm:///axis-media/media.amp QuickTimeTM supports G.711 and AAC audio encoding. The following paths can be used: - rtsp:///axis-media/media.
AXIS P5635–E PTZ Dome Network Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all settings except System Options See also the online help .
AXIS P5635–E PTZ Dome Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 18. • Stream profiles. See page 19. • Camera settings. See page 20. • Overlay image. See page 22. • Privacy mask. See page 23. • Audio settings. See page 24. • Audio clips. See page 25. Set Up Video Streams To set up the product’s video streams, go to Video & Audio > Video Stream.
AXIS P5635–E PTZ Dome Network Camera Video and Audio • Maximum frame rate. To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a fixed amount. Alternatively, the frame rate can be set as Unlimited, which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay settings. See Overlay on page 22. Click Save to apply the new settings. H.264 H.
AXIS P5635–E PTZ Dome Network Camera Video and Audio • When setting up recording using action rules. See Events on page 37. • When setting up continuous recording. See Continuous Recording on page 43. • In the Live View page – select the stream profile from the Stream profile drop-down list. For quick setup, use one of the predefined stream profiles. Each predefined profile has a descriptive name, indicating its purpose.
AXIS P5635–E PTZ Dome Network Camera Video and Audio Exposure zones - This setting determines which part of the image is used to calculate the exposure. For most situations, the Auto setting can be used. For particular requirements, select a predefined area. Shutter & Gain The shutter and gain settings affect the amount of motion blur and noise in the image. To adapt to different lighting, available storage space and bandwidth, it is often necessary to prioritize either low motion blur or low noise.
AXIS P5635–E PTZ Dome Network Camera Video and Audio Overlay Overlays are used to provide extra information, for example for forensic video analysis or during product installation and configuration. Overlays are superimposed over the video stream. An overlay text can display the current date and time, or a text string. When using a text string, modifiers can be used to display information such as the current bit rate or the current frame rate.
AXIS P5635–E PTZ Dome Network Camera Video and Audio - To scale the image automatically, select Scale with resolution. The image will be scaled down to fit the resolution used by the Axis product. 5. Click Save. To select the image to use as overlay: 1. Go to Video & Audio > Overlay Image. 2. Select the image to use from the Use overlay image list and click Save. To display the overlay image: 1. Go to Video & Audio > Video Stream and select the Image tab. 2.
AXIS P5635–E PTZ Dome Network Camera Video and Audio Since the Pan/Tilt/Zoom coordinates define its size and position, a privacy mask is dynamic in relation to the monitored area. This means that regardless of the angle and zoom of the lens, the same place or object will be hidden. To define at what magnification the mask should be displayed, zoom to the desired level and click Set level. You can add a new mask, re-size the mask with the mouse, choose a color for the mask, and give the mask a name.
AXIS P5635–E PTZ Dome Network Camera Video and Audio Use the Input gain to control the volume (dB Full Scale) of the audio input. If the sound is too low, choose a higher dB, to amplify the sound. If the sound is too high, choose a lower dB. The Level bar gives a visual representation of the audio signal level in dB relative to the full-scale input level. • Green — the signal is at a good level. • Yellow — the signal is becoming distorted. • Red — the signal is distorted.
AXIS P5635–E PTZ Dome Network Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 19. • Default Viewer for Browser. See page 26. • Viewer Settings. See page 26. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 11 . • User Defined Links. See page 27. • Output Buttons.
AXIS P5635–E PTZ Dome Network Camera Configure the Live View Page • Select Use PTZ joystick mode as default to enable joystick mode. The mode can be changed temporarily from the PTZ control panel. • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer. The recordings are saved to the location specified in the AMC Control Panel. See AXIS Media Control (AMC) on page 14.
AXIS P5635–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) Preset Positions A preset position is a saved view that can be used to quickly steer the camera to a specific position. A preset position consists of the following values: • Pan and tilt positions • Zoom position • Focus position (manual or automatic) Access the Preset Positions Preset positions can be accessed in several ways: • By selecting the preset from the Preset positions drop-down list in the Live View Page.
AXIS P5635–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) The product can be configured to return to the Home position when the PTZ functionality has been inactive for a specified length of time. Enter the length of time in the Return to home when inactive field and click Save. Set the time to zero to prevent the product from automatically returning to the Home position. Focus Window The focus window makes it possible to select an area of the camera's image that focus should be applied on.
AXIS P5635–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) To modify or remove guard tours, go to PTZ > Guard Tour, select the guard tour in the Guard Tour List and click Modify/Remove. Note For products that support Limited Guard Tour, the product has a fixed minimum view time For more information see the online help . OSDI Zones On-Screen Direction Indicator (OSDI) zones can be included in the overlay text (see Overlay on page 22) to aid the user to navigate the Axis product.
AXIS P5635–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) x Move speed sets the speed of the camera’s pan and tilt movements. The default setting is maximum speed. When using a joystick (or emulating one with the mouse) the Enable proportional speed setting can be used to reduce the maximum pan/tilt movement speed, i.e. the speed the camera view moves at when the joystick is pushed all the way out in any direction. This is useful then the view is zoomed in on an object.
AXIS P5635–E PTZ Dome Network Camera PTZ (Pan Tilt Zoom) Control Queue Note • The administrator can enable and disable PTZ controls for selected users. • To identify different users in the viewer group, cookies must be enabled on the client. • The Control queue polltime is measured in seconds. For more information see the online help . The administrator can set up a queue for PTZ controllers from PTZ > Control Queue.
AXIS P5635–E PTZ Dome Network Camera Detectors Detectors Shock Detection Enable Shock Detection from the Detectors menu. Shock detection is used, for example, to generate an alarm if the product is hit by an object or if the product is tampered with. Use the Shock sensitivity slider to adjust the sensitivity level at which the product should send an alarm. Low sensitivity value implies that the product will generate an alarm only if the hit is powerful.
AXIS P5635–E PTZ Dome Network Camera Detectors Parameter Object Size History Sensitivity Description Object size relative to window size. Object memory length. Difference in luminance between background and object. High level (100%) Only very large objects trigger motion detection. An object that appears in the window triggers motion detection for a long time before it is considered as non-moving. Ordinary colored objects on ordinary backgrounds trigger motion detection.
AXIS P5635–E PTZ Dome Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, downloads, trials and licenses, go to www.axis.
AXIS P5635–E PTZ Dome Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings.
AXIS P5635–E PTZ Dome Network Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS P5635–E PTZ Dome Network Camera Events • • • • - Day/Night Mode – Trigger the rule when the product switches between day mode (IR cut filter on) and night mode (IR cut filter off). This can for example be used to control an external infrared (IR) light connected to an output port. - Live Stream Accessed – Trigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notifications.
AXIS P5635–E PTZ Dome Network Camera Events • • System - System Ready – Trigger the rule when the product has been started and all services are running. This can for example be used to send a notification when the product restarts. - Recurrence – Trigger the rule periodically. See Set Up Recurrences on page 41. This can for example be used to upload an image every 5 minutes. - Use Schedule – Trigger the rule according to the selected schedule. See Create Schedules on page 41.
AXIS P5635–E PTZ Dome Network Camera Events Recipient Types The following recipients are available: Recipient Use with action Notes Email Send Images An email recipient can contain multiple email addresses. Send Notification Send Video Clip FTP Send Images Send Video Clip SFTP Send Images Encrypted file transfer using SSH File Transport Protocol (SFTP). SFTP is a more secure method than FTP but file transfer might be slower, especially for large files such as high resolution video.
AXIS P5635–E PTZ Dome Network Camera Events 3. Enter the email addresses to send emails to in the To field. Use commas to separate multiple addresses. 4. Select the email provider from the Provider list. 5. Enter the user ID and password for the email account. 6. Click Test to send a test email. To set up an email recipient using for example a corporate email server, follow the instructions above but select User defined as Provider. Enter the email address to appear as sender in the From field.
AXIS P5635–E PTZ Dome Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 43. • To set up action rules, see page 37. • To access recordings, see Find Recordings on page 42. • To play recordings, see Play Recording on page 42. • To export a recording as a video clip, see Export Video Clip on page 43. • To configure camera controlled storage, see Storage on page 53.
AXIS P5635–E PTZ Dome Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List. 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the filters. See also Find Recordings on page 42. 3. Select the recording and click Play. The recording will be played in a new browser window. Export Video Clip Recordings on the SD card or network share can be exported as video clips.
AXIS P5635–E PTZ Dome Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS P5635–E PTZ Dome Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS P5635–E PTZ Dome Network Camera System Options 2. Select an HTTPS certificate from the list of installed certificates. 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups. 5. Click Save to enable the settings. To access the Axis product via the desired protocol, in the address field in a browser, enter https:// for the HTTPS protocol and http:// for the HTTP protocol.
AXIS P5635–E PTZ Dome Network Camera System Options A Server/Client certificate can be self-signed or issued by a Certificate Authority (CA). A self-signed certificate offers limited protection and can be used before a CA-issued certificate has been obtained. To install a self-signed certificate: 1. Go to Setup > System Options > Security > Certificates. 2. Click Create self-signed certificate and provide the requested information. To create and install a CA-signed certificate: 1.
AXIS P5635–E PTZ Dome Network Camera System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled. IPv4 Address Configuration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.
AXIS P5635–E PTZ Dome Network Camera System Options ping -l 408 -t Windows example (this may require that you run the command prompt as an administrator) arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125 4. Check that the network cable is connected and then restart the product by disconnecting and reconnecting power. 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar. 6.
AXIS P5635–E PTZ Dome Network Camera System Options Domain name - Enter the domain(s) to search for the host name used by the Axis product. Multiple domains can be separated by semicolons. The host name is always the first part of a fully qualified domain name, for example, myserver is the host name in the fully qualified domain name myserver.mycompany.com where mycompany.com is the domain name. Primary/Secondary DNS server - Enter the IP addresses of the primary and secondary DNS servers.
AXIS P5635–E PTZ Dome Network Camera System Options Note • For NAT traversal to work, this must be supported by the router. The router must also support UPnPTM. • In this context, router refers to any network routing device such as a NAT router, Network router, Internet Gateway, Broadband router, Broadband sharing device, or a software such as a firewall. Enable/Disable - When enabled, the Axis product attempts to configure port mapping in a NAT router on your network, using UPnPTM.
AXIS P5635–E PTZ Dome Network Camera System Options SNMP The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups. AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention.
AXIS P5635–E PTZ Dome Network Camera System Options Bonjour The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. Bonjour can be disabled under System Options > Network > Bonjour. Storage SD Card NOTICE TICE NO To prevent data corruption, the SD card should be unmounted before removal. Note For SD card recommendations see www.axis.com The Axis product supports SD/SDHC/SDXC cards.
AXIS P5635–E PTZ Dome Network Camera System Options Important If autoformat is enabled, only use new or empty SD cards. Any data stored on the card will be lost when the card is inserted into the Axis product. An SD card inserted into the product can be manually formatted to one of the supported file systems. To manually format the SD card, follow these steps: 1. Insert the SD card in the SD card slot. 2. Open the Axis product’s webpages and go to Setup > System Options > Storage. 3. Click SD Card. 4.
AXIS P5635–E PTZ Dome Network Camera System Options Maintenance The Axis product provides several maintenance functions. These are available under System Options > Maintenance. Click Restart to perform a correct restart if the Axis product is not behaving as expected. This will not affect any of the current settings. Note A restart clears all entries in the Server Report. Click Restore to reset most settings to the factory default values.
AXIS P5635–E PTZ Dome Network Camera System Options You can view or download the server report. Downloading the server report creates a .zip file that contains a complete server report text file in UTF–8 format. Select the Include snapshot with default image settings option to include a snapshot of the product’s Live View. The server report .zip file should always be included when contacting support. Parameter List - Shows the product's parameters and their current settings.
AXIS P5635–E PTZ Dome Network Camera System Options 3. Keep the control button pressed for about 15–30 seconds until the status LED indicator flashes amber. 4. Release the control button. The process is complete when the status LED indicator turns green. The product has been reset to the factory default settings. If no DHCP server is available on the network, the default IP address is 192.168.0.90 5.
AXIS P5635–E PTZ Dome Network Camera Repainting the Camera Repainting the Camera The top cover can be repainted to match the installation environment. The material used in the covers is ASA+PC. Use paint suitable for this material. 1. Remove the three mounting screws. 2. Remove the three top cover screws (T20) and remove the top cover. 3. Repaint the top cover. 4. Assemble the top cover. Use the triangular marking (4) to position it correctly. 5. Fasten the top cover screws (3) with a torque of 2.
AXIS P5635–E PTZ Dome Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS P5635–E PTZ Dome Network Camera Troubleshooting The IP address is being used by another device Disconnect the Axis product from the network. Run the Ping command (in a Command/DOS window, type ping and the IP address of the product): • If you receive: Reply from : bytes=32; time=10... this means that the IP address may already be in use by another device on the network. Obtain a new IP address from the network administrator and reinstall the product.
AXIS P5635–E PTZ Dome Network Camera Troubleshooting Installation of additional ActiveX component restricted or prohibited Configure the Axis product to use a Java applet for updating video images in your browser. Go to Setup > Live View Config and select Java applet under Default viewer. Poor rendering of H.264 images Ensure that your graphics card is using the latest driver. The latest drivers can usually be downloaded from the manufacturer’s website. Color saturation is different in H.
AXIS P5635–E PTZ Dome Network Camera Troubleshooting Storage and disk management problems Storage disruption A storage disruption alarm is sent if a storage device is unavailable, removed, full, locked or if other read or write problems occur. To identify the source of the problem, check the System Log under System Options > Support > Logs & Reports. Depending on the problem, it might be necessary to re-mount the storage device.
AXIS P5635–E PTZ Dome Network Camera Technical Specifications Technical Specifications Function/group Item Specifications Camera Models AXIS P5635–E 50 Hz AXIS P5635–E 60 Hz Image sensor 1/2.9” Progressive Scan CMOS Lens Varifocal f = 4.3-129 mm F1.6 - 4.7 Autofocus Automatic day and night functionality Horizontal angle of view: 63.5˚ - 2.4˚ Vertical angle of view 38.4˚ - 1.5˚ Minimum illumination Color: 0.3 lux at 30 IRE B/W: 0.
AXIS P5635–E PTZ Dome Network Camera Technical Specifications Function/group Item Specifications Network Security Password protection, IP address filtering, IEEE 802.1X* network access control, HTTPS* encryption, digest authentication, user access log, centralized certificate management. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/), and cryptographic software written by Eric Young (eay@cryptsoft.com).
AXIS P5635–E PTZ Dome Network Camera Technical Specifications Function/group Item Specifications (Axis 10-pin Push-pull System Connector or Axis Multicable C I/O Audio Power1 m/ 5 m, sold separately) Local storage SDHC UHS-I/SDXC UHS-I slot supporting memory card up to 64 GB (card not included) Support for recording to dedicated network-attached storage (NAS) Operating conditions Temperature: -30°C to +50°C (- 4°F to 122°F) Humidity: 10 - 100% RH (condensing) Storage conditions -40°C to +70°C (-40
AXIS P5635–E PTZ Dome Network Camera Technical Specifications -/+ +/~ ~ Function Pin Notes Specifications AC/DC Power input Polarity independent Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.Ground for AC/DC 24 V AC/DC Audio connector - 4–pin terminal block used for audio in and audio line out.
AXIS P5635–E PTZ Dome Network Camera Technical Specifications 1 2 A B 1 2 A B GND DC output 12 V, max 50 mA I/O configured as input I/O configured as output Axis 10-pin Push-Pull System Connector (sold separately) When connecting external equipment to the Axis product, an Axis 10-pin Push-Pull System Connector (sold separately) is required in order to maintain the product’s IP rating. Mounting the wires requires a crimp tool. For detailed mounting instructions of the wires, visit Axis Support at www.
AXIS P5635–E PTZ Dome Network Camera Technical Specifications DC Output 2 Can be used to power auxiliary equipment. Note: This pin can only be used as power out.
User Manual AXIS P5635–E PTZ Dome Network Camera © Axis Communications AB, 2015 Ver. M1.19 Date: March 2015 Part No.
