Installation guide

ManualsBrandsAxis ManualshomeP7216

INSTALLATIONGUIDE

AXISP7216VideoEncoder

ENGLISH

Summary of content (16 pages)

PAGE 1
INSTALLATION GUIDE ENGLISH AXIS P7216 Video Encoder
PAGE 2
Legal Considerations Support Video and audio surveillance can be regulated by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license. To purchase further licenses, contact your reseller. Should you require any technical assistance, please contact your Axis reseller.
PAGE 3
Europe This digital equipment fulfills the requirements for RF emission according to the Class B limit of EN 55022. This product fulfills the requirements for immunity according to EN 61000-6-1 residential, commercial and light-industrial environments. This product fulfills the requirements for immunity according to EN 61000-6-2 industrial environments. Australia/New Zealand This digital equipment fulfills the requirements for RF emission according to the Class B limit of AS/NZS CISPR 22.
PAGE 4
PAGE 5
AXIS P7216 Video Encoder Safety Information Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE Indicates a situation which, if not avoided, could result in damage to property.
PAGE 6
AXIS P7216 Video Encoder Safety Instructions NOTICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing. • Store the Axis product in a dry and ventilated environment. • Avoid exposing the Axis product to vibration, shocks or heavy pressure. • Do not install the product on unstable or vibrating brackets, surfaces or walls.
PAGE 7
AXIS P7216 Video Encoder Installation Guide Installation Steps 1. Make sure the package contents, tools and other materials necessary for the installation are in order. See page 7 . 2. Study the hardware overview. See page 7 . 3. Study the specifications. See page 10. 4. Install the hardware. See page 13. 5. Access the product. See page 14.
PAGE 8
AXIS P7216 Video Encoder 2 3 4 5 6 7 8 9 Network connector SFP Network connector RJ45 Auxiliary connector RJ45 (maintenance) Card slot (microSD) x4 I/O terminal connector x4 RS-485/422 connector x4 Control button x4 Protective earth 1 2 9 1 2 3 4 5 6 7 8 9 8 7 3 4 6 5 Video input connector BNC x16 Network LED RJ45 Network LED SFP Network LED auxiliary Power LED Status LED 1–4 Audio out connector Audio in connector 2 Audio in connector 1 LED Indicators LED Color Indication Network Green Stea
PAGE 9
AXIS P7216 Video Encoder Connectors For specifications, see page 10. Note 75 Ohm video termination can be enabled/disabled for the video input via the product's web page at Video & Audio > Video Input > Video termination. This termination is enabled on factory default. In cases where the product is to be connected in parallel with other equipment, for optimum video quality, it is recommended that termination be enabled for only the last device in the video signal chain.
PAGE 10
AXIS P7216 Video Encoder Power connector - 2-pin terminal block for power input. Use a limited power source (LPS) with either a rated output power limited to £100 W or a rated output current limited to £5 A. I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications.
PAGE 11
AXIS P7216 Video Encoder Connectors I/O terminal connector • Digital Input • Digital Output • Auxiliary power and ground (GND) ENGLISH 6-pin terminal block for: 1 2 3 4 5 6 Function Pin Notes GND 1 Ground 3.3 V DC Power 2 Can be used to power auxiliary equipment. Note: This pin can only be used as power out. Max load = 250 mA Configurable (Input or Output) 3– 6 Digital input — Connect to GND to activate, or leave floating (unconnected) to deactivate.
PAGE 12
AXIS P7216 Video Encoder must be connected in parallel with the load, for protection against voltage transients. 1 2 3.3 V max 250 mA A B A B I/O configured as input I/O configured as output Power connector DC power input 2-pin terminal block for power input. Use a limited power source (LPS) with either a rated output power limited to £100 W or a rated output current limited to £5 A. Audio connector 3.
PAGE 13
AXIS P7216 Video Encoder 1 Tip Audio Input Audio Output Microphone/Line in Line out (mono) Ground Ground 3 Sleeve ENGLISH 2 Ring RS-485/422 connector Two 2-pin terminal blocks for RS485/RS422 serial interface.
PAGE 14
AXIS P7216 Video Encoder Connect the cables 1. 2. 3. 4. 5. 6. Connect the video encoder to the network using a network cable RJ45 and/or a SFP cable. Optionally connect the external input/output devices. Optionally connect active speakers and/or external microphones. Connect the cameras to the video inputs. Connect the supplied indoor power adapter. Check that the indicator LEDs indicate the correct conditions.
PAGE 15
AXIS P7216 Video Encoder Further Information The User Manual is available at www.axis.com Visit Axis learning center www.axis.com/academy for useful trainings, webinars, tutorials and guides. Warranty Information For information about Axis’ product warranty and thereto related information, see www.axis.com/warranty/ 15 ENGLISH Visit www.axis.com/techsup to check if there is updated firmware available for your network product. To see the currently installed firmware version, go to Setup > About.